| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| Engine switch on (IG) for 1 second | When any condition below is met (1 trip detection logic):
·
Injector compensation code is not registered. ·
Wrong injector compensation code is registered. ·
Injector pilot quantity learning value is not registered. ·
Crank Time Compensation Learning value is not registered.* ·
A/F sensor compensation learning value is not registered.* |
·
Injector compensation code ·
Injector pilot quantity learning value ·
Crank time compensation learning value ·
ECM ·
A/F sensor compensation learning value |
*: When this malfunction occurs, the MIL does not illuminate.
When a injector assembly is replaced, the new injector compensation code must be input into the ECM. When the ECM is replaced, all of the existing injector compensation codes must be input into the new ECM.
Injector compensation codes are unique, 30-digit, alphanumeric values printed on the head portion of each injector assembly. If an incorrect injector compensation code is input into the ECM, the engine assembly may rattle or engine idling may become rough. In addition, engine failure may occur and the life of the engine may be shortened.
When a injector assembly is replaced, perform pilot quantity learning. When the ECM is replaced, all of the existing pilot quantity learning values must be input into the new ECM.
When replacing the ECM with a new one, if the injector compensation code and pilot quantity learning value are not entered or the injector compensation code is not registered correctly, DTC P062F will be stored.
When replacing the ECM with a new one, input all learning values and codes into the new ECM as follows:
Prior to replacing the ECM, use the GTS to read and save each learning value and code from the original ECM (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).
After installing a new ECM, input the saved learning values and codes into the new ECM using the GTS (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).
Turn the engine switch off and turn the GTS off.
Wait for at least 30 seconds.
Turn the engine switch on (IG) and turn the GTS on.
Clear DTC P062F stored in the ECM using the GTS (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>DTC CHECK / CLEAR).
Each injector assembly has different fuel injection characteristics. In order to optimize the fuel injections, the ECM uses the injector compensation codes to balance the different fuel injections between each injector assembly.
When you first turn ON the engine switch after replacing the ECM and other component(s), DTC P062F is stored. Manually clear the DTC upon completion of compensation code registration.
| Replacement Part | Utility Item |
|---|---|
| ECM |
|
| Injector Assembly |
|
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Do not start the engine.
Enter the following menus: Powertrain / Engine and ECT / Utility / Learning Values Confirmation (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).
| Result | Proceed to |
|---|---|
| The injector compensation codes are not input | A |
| The injector compensation codes registered in the ECM are different than the codes imprinted on the injectors | B |
| The pilot quantity learning values are set to the default values | C |
| Except above | D |
When the pilot quantity learning values are set to the default values, "7FFF" is displayed.
A
B
C
D
Install the old ECM.
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Utility / Learning Values Save.
Perform the Learning Values Save (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).
| Result | Proceed to |
|---|---|
| Learning Values Save is complete | A |
| Learning Values Save is fail | B |
A
B
When replacing the ECM, after performing "Learning Values Save" to save the learned values from the old ECM using the GTS and replacing the old ECM with a new one, "Learning Values Write" was not performed using the GTS causing this DTC to be output.
Remove the old ECM.
Install the new ECM.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Utility / Learning Values Write.
Perform the Learning Values Write (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).
| Result | Proceed to |
|---|---|
| Learning Values Write is complete | A |
| Learning Values Write is fail | B |
B
A
Remove the new ECM.
Install the old ECM.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Utility / Learning Values Save (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).
NEXT
Remove the old ECM.
Install the new ECM.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Utility / Learning Values Write.
Perform the Learning Values Write (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).
| Result | Proceed to |
|---|---|
| Learning Values Write is fail | A |
| Learning Values Write is complete | B |
A
B
Register the injector compensation code (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).
NEXT
Perform the fuel injector pilot quantity learning (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).
NEXT
Connect the GTS to the DLC3.
Clear the DTCs (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>DTC CHECK / CLEAR).
Turn the engine switch off and leave the vehicle for 30 seconds or more.
Turn the engine switch on (IG) for 1 second.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P062F is output | A |
| No DTC is output | B |
A
B
Replace the ECM (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL).
NEXT
Connect the GTS to the DLC3.
Clear the DTCs (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>DTC CHECK / CLEAR).
Turn the engine switch off and leave the vehicle for 30 seconds or more.
Turn the engine switch on (IG) for 1 second.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Confirm that the DTC is not output again.
NEXT