Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260475 ECD SYSTEM C

1GD-FTV ENGINE CONTROL  ECD SYSTEM  P0489  Exhaust Gas Recirculation Control Circuit Low  P0490  Exhaust Gas Recirculation Control Circuit High  


DESCRIPTION

The EGR actuator is operated by the ECM and opens and closes the EGR valve using gears. The opening angle of the EGR valve is detected by the EGR position sensor, which is mounted on the electric EGR control valve assembly.

P0489
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Idle the engine for 5 seconds or more Both of the following conditions are met for 2.0 seconds:
(1 trip detection logic)
·

The EGR actuator duty cycle is 80% or higher.

·

EGR actuator current is below 0.5 A.


·

Open or short in EGR actuator circuit

·

Electric EGR control valve assembly

·

ECM



P0490
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Idle the engine for 5 seconds or more An EGR actuator current of 8 A or higher or the ECM internal circuit temperature of 150 to 160°C (302 to 320°F) or higher is detected.
(1 trip detection logic)
·

Open or short in EGR actuator circuit

·

Electric EGR control valve assembly

·

ECM



Related Data List
DTC No. Data List
P0489
P0490
·

Actual EGR Valve Pos

·

Target EGR Valve Pos



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT ELECTRIC EGR CONTROL VALVE ASSEMBLY
a.

Remove the electric EGR control valve assembly (See page Engine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EGR VALVE>REMOVAL).


b.
A351114E01
0.122,0.056 0.431,0.212 0.309,0.156 10 *a 1.561,1.693 1.870,1.849 0.309,0.156 10 M+ 0.5,1.667 0.809,1.823 0.309,0.156 10 M- 0.956,1.139 0.805,1.749 false 0.805,1.749 0.728,1.749 false 1.317,1.134 1.411,1.77 false 1.411,1.77 1.518,1.77 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (M-) - 4 (M+) Always No short or open circuit


Text in Illustration
*a Component without harness connected
(Electric EGR Control Valve Assembly)



OK

2.CHECK HARNESS AND CONNECTOR (ELECTRIC EGR VALVE ASSEMBLY - ECM)

NG

4.REPLACE ELECTRIC EGR VALVE ASSEMBLY
2.CHECK HARNESS AND CONNECTOR (ELECTRIC EGR VALVE ASSEMBLY - ECM)
a.

Disconnect the electric EGR valve assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C127-4 (M+) - C151-6 (EGM+) Always Below 1 Ω
C127-5 (M-) - C151-7 (EGM-) Always Below 1 Ω
C127-4 (M+) or C151-6 (EGM+) - Body ground and other terminals Always 10 kΩ or higher
C127-5 (M-) or C151-7 (EGM-) - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the electric EGR valve assembly connector.


e.

Reconnect the ECM connector.



OK

3.REPLACE ECM

NG

5.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.REPLACE ECM

NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.REPLACE ELECTRIC EGR VALVE ASSEMBLY
a.

Replace the electric EGR valve assembly (See page Engine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EGR VALVE>REMOVAL).



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.



c.

Turn the engine switch off for 30 seconds or more.


d.

Turn the engine switch on (IG) and turn the GTS on.


e.

Start the engine.


f.

Idle the engine for 5 seconds or more


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


h.

Confirm that the DTC is not output again.



NEXT

END