For more information on the differential pressure sensor and Diesel Particulate Filter (DPF), refer to the following procedures (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>SYSTEM DESCRIPTION).
If P2454 and/or P2455 is present, refer to the DTC chart for DPF system (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>SYSTEM DESCRIPTION).
The two sensing chambers of the differential pressure sensor are mounted to monitor the pressure before and after the DPF catalytic converter. The sensor itself is not located on the engine assembly in order to reduce the influence of vibration.
The ECM compares the exhaust gas pressure before and after the DPF catalytic converter by monitoring the pressure using the upstream and downstream sensing chambers of the differential pressure sensor. If the difference in pressure exceeds a predetermined level, the ECM judges that the catalytic converter is clogged with particulate matter (PM). When the ECM judges that a partially clogged condition exists, the ECM begins to perform PM forced regeneration.
When the output voltage of the sensor deviates from the normal operating range, the ECM interprets this as a malfunction of the sensor circuit, and sets DTC P2454 or P2455, and illuminates the MIL.
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| Engine switch on (IG) for 5 seconds | Differential pressure sensor output voltage is below 0.4 V for 3 seconds or more.
(1 trip detection logic) |
·
Open or short in differential pressure sensor circuit ·
Incorrect air hose routing ·
Differential pressure sensor ·
ECM |
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| Engine switch on (IG) for 5 seconds | Differential pressure sensor output voltage is higher than 4.8 V for 3 seconds or more.
(1 trip detection logic) |
·
Open or short in differential pressure sensor circuit ·
Incorrect air hose routing ·
Differential pressure sensor ·
ECM |
| DTC No. | Data List |
|---|---|
| P2454
P2455 |
DPF Differential Pressure |
DTC P2453 (Diesel Particulate Filter Pressure Sensor "A" Circuit Range / Performance) will be stored if there is incorrect vacuum hose routing to the differential pressure sensor assembly.
After confirming DTC P2454 and P2455, check the differential pressure in the "Powertrain / Engine and ECT / Data List / DPF Differential Pressure" menu using the GTS.
| Condition | DPF Differential Pressure Output | Sensor Condition |
|---|---|---|
| Engine switch on (IG) | Approximately 0 kPa | Normal |
| Always | -5 kPa or less or higher than 99 kPa | Open or short circuit |
| 4000 rpm (No engine load) | Negative output | Incorrect hose routing |
In order to detect abnormality in the differential pressure sensor, the ECM always monitors the output voltage from the sensor. When the sensor output voltage deviates from the normal operating range (between 0.4 V and 4.8 V) for more than 3 seconds, the ECM interprets this as a malfunction in the sensor circuit and illuminates the MIL.
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Disconnect the differential pressure sensor connector.
Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C129-3 (VC) - C129-1 (E2) | Engine switch on (IG) | 4.5 to 5.5 V |
| *a | Front view of wire harness connector
(to Differential Pressure Sensor) |
Reconnect the differential pressure sensor connector.
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C151-27 (PEX) - C151-26 (EPEX) | Engine switch on (IG) | 0.4 to 4.8 V |
| *a | Component with harness connected
(ECM) |
NG
OK
Disconnect the differential pressure sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C129-2 (PEX) - C151-27 (PEX) | Always | Below 1 Ω |
| C129-3 (VC) - C151-32 (VCPX) | Always | Below 1 Ω |
| C129-1 (E2) - C151-26 (EPEX) | Always | Below 1 Ω |
| C129-2 (PEX) or C151-27 (PEX) - Body ground and other terminals | Always | 10 kΩ or higher |
| C129-3 (VC) or C151-32 (VCPX) - Body ground and other terminals | Always | 10 kΩ or higher |
Reconnect the differential pressure sensor connector.
Reconnect the ECM connector.
OK
NG
Disconnect the differential pressure sensor connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C129-3 (VC) - C129-2 (PEX) | Engine switch off | No short or open circuit |
| C129-2 (PEX) - C129-1 (E2) |
| *a | Front view of wire harness connector
(to Differential Pressure Sensor) |
Reconnect the differential pressure sensor connector.
OK
NG
Replace the differential pressure sensor (See page Engine / Hybrid System>1GD-FTV (EMISSION CONTROL)>DIFFERENTIAL PRESSURE SENSOR>REMOVAL).
NEXT
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C151-32 (VCPX) - C151-26 (EPEX) | Engine switch on (IG) | 4.5 to 5.5 V |
| *a | Component with harness connected
(ECM) |
OK
NG
Replace the ECM (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL).
NEXT
Repair or replace the harness or connector.
NEXT
Connect the GTS to the DLC3.
Clear the DTCs (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>DTC CHECK / CLEAR).
Turn the engine switch on (IG) and wait for 5 seconds.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Confirm that the DTC is not output again.
NEXT