Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260475 ECD SYSTEM C

1GD-FTV ENGINE CONTROL  ECD SYSTEM  P0100  Mass Air Flow Circuit  


DESCRIPTION

The mass air flow meter sub-assembly is a sensor that measures the intake air volume using the following built-in components:

·

By-pass duct (allows some of the intake air to flow past a silicon chip sensor).

·

Silicon chip sensor (uses a heater control bridge circuit and temperature sensor bridge circuit to detect the difference in the temperature of the intake air that passes the sensors positioned before and after the heater).

·

Control circuit (converts the difference in temperature into a pulse signal and performs correction).


Intake air flows past the temperature sensor (before heater), the heater, and then the temperature sensor (after heater) of the silicon chip sensor in the by-pass duct. As the intake air is warmed up when it is exposed to the heater, the temperature of the intake air as it flows past the temperature sensor (after heater) is higher than when it flows past the temperature sensor (before heater). The difference in temperature of the intake air at each temperature sensor varies depending on the velocity of the intake air that flows past the silicon chip sensor. The temperature sensor bridge circuit detects the difference in temperature and the control circuit converts it into a pulse signal and outputs it to the ECM. When the temperature detected by the temperature sensor (before heater) is higher than that detected by the temperature sensor (after heater), backflow of the intake air is detected.

The ECM calculates the intake air volume based on the pulse signal received from the mass air flow meter sub-assembly.

The heater control bridge circuit has a temperature sensor and power transistor, and maintains the heater temperature at a specific temperature.

A332068E02
2.198,0.833 1.698,0.948 1.698,0.948 1.542,0.948 false 2.333,0.823 2.927,0.979 2.927,0.979 3.083,0.979 false 3.104,1.417 3.292,1.573 3.292,1.573 3.438,1.573 false 2.698,1.542 2.969,1.792 2.969,1.792 3.125,1.792 false 1.823,1.542 1.531,1.792 1.531,1.792 1.406,1.792 false 5.625,2.896 5.917,3.49 5.917,3.49 6.073,3.49 false 5.219,2.302 4.927,2.552 4.927,2.552 4.802,2.552 false 5.49,1.917 6.198,2.75 6.198,2.75 6.344,2.75 false 1.313,0.844 1.625,1.042 0.313,0.198 10 false *d 3.146,0.875 3.458,1.073 0.313,0.198 10 false *c 3.479,1.458 3.719,1.667 0.24,0.208 10 false *e 3.177,1.698 3.417,1.906 0.24,0.208 10 false *f 1.198,1.688 1.438,1.896 0.24,0.208 10 false *g 4.708,0.427 5.021,0.625 0.313,0.198 10 false *1 0.802,3.833 1.031,4.031 0.229,0.198 10 false *c 1.198,3.833 1.427,4.031 0.229,0.198 10 false *d 1.719,3.844 1.948,4.042 0.229,0.198 10 false *h 2.438,4.083 2.667,4.281 0.229,0.198 10 false *l 2.427,3.448 2.656,3.646 0.229,0.198 10 false *j 2.771,3.448 3,3.646 0.229,0.198 10 false *k 2.76,4.083 2.99,4.281 0.229,0.198 10 false *m 3.521,3.896 3.75,4.094 0.229,0.198 10 false *i 3.438,3.313 3.667,3.51 0.229,0.198 10 false *n 4.167,2.646 4.438,2.844 0.271,0.198 10 false 5V 4.146,3.313 4.417,3.51 0.271,0.198 10 false FG 4.156,4.292 4.521,4.49 0.365,0.198 10 false E2G 6.115,3.385 6.344,3.583 0.229,0.198 10 false *q 4.563,2.448 4.792,2.646 0.229,0.198 10 false *b 6.396,2.646 6.625,2.844 0.229,0.198 10 false *a

Text in Illustration
*1 Mass Air Flow Meter Sub-assembly - -
*a Silicon Chip Sensor *b By-pass Duct
*c Heater *d Heater Thermistor
*e Intake Air *f Temperature Sensor (After Heater)
*g Temperature Sensor (Before Heater) *h Intake Air Thermistor 1
*i Intake Air Thermistor 2 *j Temperature Sensor (Before Heater) 1
*k Temperature Sensor (After Heater) 2 *l Temperature Sensor (After Heater) 1
*m Temperature Sensor (Before Heater) 2 *n Control Circuit
*o Heater Control Bridge Circuit *p Temperature Sensor Bridge Circuit
*q Air Flow - -

P0100
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
3 seconds after engine is started Mass air flow meter sub-assembly signal frequency is less than 0.1 kHz with the engine speed at 400 rpm or more for 3 seconds (1 trip detection logic).
·

Open or short in mass air flow meter sub-assembly circuit

·

Mass air flow meter sub-assembly

·

ECM



Related Data List
DTC No. Data List
P0100 MAF

HINT:

If DTC P0100 is stored, the following symptoms may appear (as the ECM mistakenly determines that there is less air than the actual intake air amount, EGR is decreased according to the target EGR):

-

Combustion noise worsens




WIRING DIAGRAM

A348535E10
2.198,2.052 2.656,2.25 0.458,0.198 10 false 2 1.906,0.656 2.365,0.854 0.458,0.198 10 false 5V 1.885,1.24 2.344,1.438 0.458,0.198 10 false FG 1.813,1.833 2.271,2.031 0.458,0.198 10 false E2G 2.208,2.625 2.667,2.823 0.458,0.198 10 false 4 2.188,1.438 2.646,1.635 0.458,0.198 10 false 1 2.188,0.896 2.646,1.094 0.458,0.198 10 false 3 1.823,2.375 2.281,2.573 0.458,0.198 10 false THA 0.656,3.198 1.115,3.396 0.458,0.198 10 false C33 0.635,3.375 2.99,3.615 2.354,0.24 10 false Mass Air Flow Meter Sub-assembly 4.938,0.885 5.396,1.083 0.458,0.198 10 false 25 4.917,1.469 5.375,1.667 0.458,0.198 10 false 33 4.927,2.063 5.385,2.26 0.458,0.198 10 false 24 4.938,2.615 5.396,2.813 0.458,0.198 10 false 32 5.552,3.208 6.01,3.406 0.458,0.198 10 false C150 5.583,3.375 6.042,3.573 0.458,0.198 10 false ECM 5.188,1.25 5.646,1.448 0.458,0.198 10 false VG 5.177,1.823 5.635,2.021 0.458,0.198 10 false EVG 5.177,2.385 5.635,2.583 0.458,0.198 10 false THA 5.188,0.667 5.646,0.865 0.458,0.198 10 false VCVG

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK MASS AIR FLOW METER SUB-ASSEMBLY (POWER SOURCE OF MASS AIR FLOW METER SUB-ASSEMBLY)
a.
A332051E01
0.25,1.917 0.667,2.167 0.417,0.25 2.156,3.104 1.823,2.406 true 1.104,3.094 1.375,2.396 true 1.583,3.094 1.594,2.396 true 0.896,0.667 1.208,0.823 0.313,0.156 10 false *a 2.135,3.135 2.479,3.354 0.344,0.219 10 false 5V 0.333,1.969 0.792,2.167 0.458,0.198 10 false C33 0.99,3.135 1.333,3.354 0.344,0.219 10 false FG 1.49,3.146 1.833,3.365 0.344,0.219 10 false E2G

Disconnect the mass air flow meter sub-assembly connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C33-3 (5V) - Body ground Engine switch on (IG) 4.8 to 5.2 V
C33-1 (FG) - C33-2 (E2G) Engine switch on (IG) 4.8 to 5.2 V


Text in Illustration
*a Front view of wire harness connector
(to Mass Air Flow Meter Sub-assembly)


d.

Reconnect the mass air flow meter sub-assembly connector.



OK

2.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

NG

5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
2.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY
a.

Replace the mass air flow meter sub-assembly (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>MASS AIR FLOW METER>REMOVAL).



NEXT

3.CHECK IF DTC RECURS (SEE IF DTC P0100 IS OUTPUT AGAIN)
3.CHECK IF DTC RECURS (SEE IF DTC P0100 IS OUTPUT AGAIN)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.



d.

Turn the engine switch off and wait for at least 30 seconds.


e.

Turn the engine switch on (IG) and turn the GTS on.


f.

Start the engine and wait for 3 seconds or more.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


h.

Read the DTCs.

Result
Result Proceed to
DTC P0100 is output A
DTCs are not output B



A

4.REPLACE ECM

B

END

4.REPLACE ECM

NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C33-3 (5V) - C150-25 (VCVG) Always Below 1 Ω
C33-1 (FG) - C150-33 (VG) Always Below 1 Ω
C33-2 (E2G) - C150-24 (EVG) Always Below 1 Ω
C33-3 (5V) or C150-25 (VCVG) - Body ground and other terminals Always 10 kΩ or higher
C33-1 (FG) or C150-33 (VG) - Body ground and other terminals Always 10 kΩ or higher
C33-2 (E2G) or C150-24 (EVG) - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the mass air flow meter sub-assembly connector.


e.

Reconnect the ECM connector.



OK

6.REPLACE ECM

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.REPLACE ECM

NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.



d.

Turn the engine switch off and wait for at least 30 seconds.


e.

Turn the engine switch on (IG) and turn the GTS on.


f.

Start the engine and wait for 3 seconds or more.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


h.

Confirm that the DTC is not output again.



NEXT

END