Home › Engine / Hybrid System › 5L-E (ENGINE MECHANICAL) › CYLINDER HEAD
RM27T0E _51 Engine / Hybrid System _053661 5L-E ENGINE MECHANICAL _0260476 CYLINDER HEAD G

5L-E ENGINE MECHANICAL  CYLINDER HEAD  INSPECTION  


PROCEDURE

Hide 11101 1.CLEAN CYLINDER HEAD SUB-ASSEMBLY

a.

Clean the cylinder head.

i.

Using a gasket scraper, remove all the gasket material from the surface that contact the cylinder block.

NOTICE:

Do not scratch the surface that contacts the cylinder block.




b.

Using a wire brush, remove all the carbon from the combustion chambers.

NOTICE:

Do not scratch the surface that contacts the cylinder block.



c.

Using a valve guide bushing brush and solvent, clean all the guide bushes.


d.

Using a soft brush and solvent, thoroughly clean the cylinder head.


Hide 11101 2.INSPECT CYLINDER HEAD SUB-ASSEMBLY

A378632E01
0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 0.198,3.177 0.51,3.375 0.313,0.198 10 false *c 0.188,1.729 0.5,1.927 0.313,0.198 10 false *b

a.

Inspect the cylinder head warpage.

i.

Using a precision straightedge and feeler gauge, measure the surfaces that contact the cylinder block and the manifolds for warpage.

Maximum warpage:

0.20 mm (0.00787 in.)


Text in Illustration
*a Cylinder Block Side:
*b Intake Manifold Side:
*c Exhaust Manifold Side:

If the warpage is more than the maximum, replace the cylinder head sub-assembly.



b.

Inspect the cylinder head for cracks.

i.

Using a dye penetrant, check the combustion chamber, intake ports, exhaust ports and cylinder head surface for cracks.

If cracked, replace the cylinder head sub-assembly.



Hide 3.CLEAN VALVE

a.

Using a gasket scraper, chip off any carbon from the valve head.


b.

Using a wire brush, thoroughly clean the valve.


Hide 13711 4.INSPECT INTAKE VALVE

a.

Using a micrometer, measure the diameter of the valve stem.

Standard valve stem diameter:

7.975 to 7.990 mm (0.3140 to 0.3146 in.)


If the diameter is not as specified, replace the intake valve.


b.
A303230E01
3.094,1.792 3.302,2.021 0.208,0.229 10 false *1

Check the valve face angle.

i.

Grind the valve enough to remove any pits and carbon.


ii.

Check that the valve is ground to the correct valve face angle.

Standard valve face angle:

44.5°


Text in Illustration
*1 Valve Face Angle

If the valve is worn, replace the intake valve.



c.
A303231E01
0.479,1.656 0.792,1.854 0.313,0.198 10 false *1

Check the head margin thickness.

Standard margin thickness:

1.6 mm (0.0630 in.)


Minimum margin thickness:

1.1 mm (0.0433 in.)


Text in Illustration
*1 Margin Thickness

If the margin thickness is less than the minimum, replace the intake valve.


d.

Check the overall length of the valve.

Standard overall length:

104.10 to 104.50 mm (4.10 to 4.11 in.)


Minimum overall length:

103.60 mm (4.08 in.)


If the overall length is less than the minimum, replace the intake valve.


e.
A303232

Check the surface of the valve stem tip for wear.

If the valve stem tip is worn, resurface the tip with a grinder or replace the intake valve.

NOTICE:

Do not grind the valve so it becomes shorter than the minimum overall length.



Hide 13715 5.INSPECT EXHAUST VALVE

a.

Using a micrometer, measure the diameter of the valve stem.

Standard valve stem diameter:

7.960 to 7.975 mm (0.3134 to 0.3140 in.)


If the diameter is not as specified, replace the exhaust valve.


b.
A303230E02
3.021,1.802 3.333,2 0.313,0.198 10 false *1

Check the valve face angle.

i.

Grind the valve enough to remove any pits and carbon.


ii.

Check that the valve is ground to the correct valve face angle.

Standard valve face angle:

44.5°


Text in Illustration
*1 Valve Face Angle

If the valve face is worn, replace the exhaust valve.



c.
A303231E02
0.469,1.667 0.781,1.865 0.313,0.198 10 false *1

Check the valve head margin thickness.

Standard margin thickness:

1.7 mm (0.0669 in.)


Minimum margin thickness:

1.2 mm (0.0472 in.)


Text in Illustration
*1 Margin Thickness

If the margin thickness is less than the minimum, replace the exhaust valve.


d.

Check the overall length of the valve.

Standard overall length:

103.95 to 104.35 mm (4.09 to 4.11 in.)


Minimum overall length:

103.45 mm (4.07 in.)


If the overall length is less than the minimum, replace the exhaust valve.


e.
A303232

Check the surface of the valve stem tip for wear.

If the valve stem tip is worn, resurface the tip with a grinder or replace the exhaust valve.

NOTICE:

Do not grind the valve so it becomes shorter than the minimum overall length.



Hide 13711B 6.INSPECT INNER COMPRESSION SPRING

a.
A303233E01
1.208,0.063 1.521,0.26 0.313,0.198 10 false *1

Using a steel square, measure the deviation of the spring.

Maximum deviation:

2.0 mm (0.0787 in.)


Text in Illustration
*1 Deviation

If the deviation is more than the maximum, replace the spring.


b.
EM00801

Using a vernier caliper, measure the free length of the spring.

Standard Free Length:

46.20 mm (1.82 in.)


If the free length is not as specified, replace the spring.


c.
EM00281

Using a spring tester, measure the tension of the valve spring at the installed length.

Standard tension:

301 to 332 N (31 to 34 kgf, 66.6 to 74.6 lbf) at 37.00 mm (1.46 in.)


If the tension is not as specified, replace the spring.


Hide 11122 7.INSPECT INTAKE VALVE GUIDE BUSH

a.
A303239

Using a caliper gauge, measure the inside diameter of the guide bush.

Standard bush inside diameter:

8.010 to 8.030 mm (0.315 to 0.316 in.)



b.

Subtract the valve stem diameter measurement from the guide bush inside diameter measurement.

Standard oil clearance:

0.020 to 0.055 mm (0.000787 to 0.00217 in.)


Maximum oil clearance:

0.08 mm (0.00315 in.)


If the clearance is more than the maximum, replace the intake valve and guide bush.


Hide 11126 8.INSPECT EXHAUST VALVE GUIDE BUSH

a.
A303243

Using a caliper gauge, measure the inside diameter of the guide bush.

Standard bush inside diameter:

8.010 to 8.030 mm (0.315 to 0.316 in.)



b.

Subtract the valve stem diameter measurement from the guide bush inside diameter measurement.

Standard oil clearance:

0.035 to 0.070 mm (0.00138 to 0.00276 in.)


Maximum oil clearance:

0.10 mm (0.00394 in.)


If the clearance is more than the maximum, replace the exhaust valve and guide bush.


Hide 9.INSPECT VALVE SEAT

a.
A057256E04
1.896,0.906 2.219,0.594 2.219,0.594 2.354,0.594 false 2.417,0.5 2.594,0.667 0.177,0.167 10 false *1

Using a 45° carbide cutter, resurface the valve seats. Remove only enough metal to clean the seats.

Text in Illustration
*1 45° Carbide Cutter


b.
A057247E06
1.281,0.99 1.479,1.198 0.198,0.208 10 false *1

Check the valve seating position.

Text in Illustration
*1 Width

i.

Apply a light coat of Prussian blue to the valve face.


ii.

Lightly press the valve against the seat. Do not rotate valve.


iii.

Prussian blue appears 360° around the entire valve face, the valve is concentric. If not, replace the valve.


iv.

Prussian blue appears 360° around the entire valve seat, the guide and face are concentric. If not, resurface the seat.


v.

Check that the seat contacts the middle of the valve face with the width below:

Standard width:

1.5 to 1.9 mm (0.0591 to 0.0748 in.)




Hide 10.INSPECT EXHAUST VALVE SEATS

a.
A057255

Using a 45° carbide cutter, resurface the valve seats. Remove only enough metal to clean the seats.


b.
A057246E06
1.167,0.948 1.323,1.115 0.156,0.167 10 false *1

Check the valve seating position.

i.

Apply a light coat of Prussian blue to the valve face.


ii.

Lightly press the valve against the seat. Do not rotate valve.


iii.

Prussian blue appears 360° around the entire valve face, the valve is concentric. If not, replace the valve.


iv.

Prussian blue appears 360° around the entire valve seat, the guide and face are concentric. If not, resurface the seat.


v.

Check that the seat contacts the middle of the valve face with the width below:

Standard width:

1.8 to 2.2 mm (0.0708 to 0.0866 in.)


Text in Illustration
*1 Width



Hide 13751 11.INSPECT VALVE LIFTER

a.
A058346

Using a micrometer, measure the lifter diameter.

Standard lifter diameter:

40.892 to 40.902 mm (1.6099 to 1.6103 in.)



b.
A057262

Using a caliper gauge, measure the lifter bore diameter of the cylinder head.

Standard lifter bore diameter:

40.960 to 40.980 mm (1.6126 to 1.6134 in.)



c.

Subtract the lifter diameter measurement from the lifter bore diameter measurement.

Standard oil clearance:

0.058 to 0.088 mm (0.00238 to 0.00346 in.)


Maximum oil clearance:

0.10 mm (0.00394 in.)


If the oil clearance is more than the maximum, replace the lifter. If necessary, replace the cylinder head.


Hide 12.INSPECT CAMSHAFT OIL CLEARANCE

a.

Inspect the journal diameter of the camshaft.

i.

Using a micrometer, measure the journal diameter of the camshaft for the camshaft bearing.

Standard Journal Diameter:
Item Specified Condition
No. 1 journal 34.969 to 34.985 mm (1.3767 to 1.3774 in.)
Other journals 27.969 to 27.985 mm (1.101 to 1.102 in.)


If the journal diameter is not as specified, check the oil clearance.



b.
A056923E04
0.417,0.26 0.521,0.26 0.521,0.26 1.25,0.979 false 0.188,0.177 0.365,0.344 0.177,0.167 10 false *1

Check the oil clearance.

i.

Clean the bearing caps and journals.


ii.

Check the bearings for flaking and scoring.

If the bearings are damaged, replace the bearing caps and cylinder head as a set.


iii.

Install the bearings to the bearing caps and cylinder head.


iv.

Place the camshaft on the cylinder head.


v.

Lay a strip of Plastigage across each of the journals.

Text in Illustration
*1 Plastigage


vi.

Install the bearing caps (See page Engine / Hybrid System>5L-E (ENGINE MECHANICAL)>CAMSHAFT>INSTALLATION).

NOTICE:

Do not turn the camshaft.



vii.

viii.
A056924E04
0.375,0.417 0.521,0.417 0.521,0.417 1.156,1 false 0.135,0.333 0.313,0.51 0.177,0.177 10 false *1

Measure the Plastigage at its widest point.

Standard oil clearance:

0.022 to 0.074 mm (0.000866 to 0.00291 in.)


Maximum oil clearance:

0.10 mm (0.00394 in.)


Text in Illustration
*1 Plastigage

If the oil clearance is more than the maximum, replace the cylinder head sub-assembly. If necessary, grind or replace the camshaft.


ix.

Completely remove the Plastigage.


x.

Remove the camshaft.



Hide 13.INSPECT CAMSHAFT THRUST CLEARANCE

a.

Check the thrust clearance.

i.

Install the camshaft.


ii.
A056921

Using a dial indicator, measure the thrust clearance while moving the camshaft back and forth.

Standard thrust clearance:

0.080 to 0.280 mm (0.00351 to 0.0110 in.)


Maximum thrust clearance:

0.35 mm (0.0138 in.)


If the thrust clearance is more than the maximum, replace the No. 1 bearing. If necessary, replace the camshaft.