Home › Engine / Hybrid System › 5L-E (ENGINE MECHANICAL) › CYLINDER BLOCK
RM27T0E _51 Engine / Hybrid System _053661 5L-E ENGINE MECHANICAL _0260477 CYLINDER BLOCK A

5L-E ENGINE MECHANICAL  CYLINDER BLOCK  REPLACEMENT  


PROCEDURE

Hide 1.REPLACE TIGHT PLUG

NOTICE:

If coolant leaks from the tight plug or the plug is corroded, replace it.


A118124E04
5.104,0.396 5.302,0.604 0.198,0.208 10 false *b 6.26,3.49 6.469,3.708 0.208,0.219 10 false *d 1.781,0.354 1.969,0.573 0.188,0.219 10 false *a 1.771,2.635 1.938,2.844 0.167,0.208 10 false *c 1.74,1.354 1.948,1.531 0.208,0.177 10 true A 1.5,3.833 1.698,4.01 0.198,0.177 10 true B 5.104,1.521 5.313,1.698 0.208,0.177 10 true C 2.115,3.844 2.302,4.01 0.188,0.167 10 true B 2.677,3.844 2.823,4.073 0.146,0.229 10 true B 0.948,3.833 1.135,4.021 0.188,0.188 10 true B 2.323,1.333 2.531,1.5 0.208,0.167 10 true A

Text in Illustration
*a Right Side *b Rear Side
*c Left Side *d Stops

a.

Apply adhesive to new tight plugs.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



b.

Install the tight plugs as shown in the illustration.


c.

Using SST, tap in the 2 tight plugs labeled A.

SST
09950-60010  (09951-00250)
09950-70010  (09951-07100)


d.

Using SST, tap in the 4 tight plugs labeled B.

SST
09950-60010  (09951-00350)
09950-70010  (09951-07100)


e.

Using SST, tap in the tight plug labeled C.

SST
09950-60010  (09951-00500)
09950-70010  (09951-07100)


Hide 2.REPLACE STRAIGHT PIN

NOTICE:

It is not necessary to remove a straight pin unless it is being replaced.


a.

Install the straight pins as shown in the illustration.

A071267E05
0.948,0.115 1.146,0.323 0.198,0.208 10 false *a 3.906,0.063 5.094,0.302 1.188,0.24 10 false 10 mm (0.394 in.) 3.292,0.802 3.958,1.188 0.667,0.385 10 false 22 mm (0.866 in.) 6.396,1.365 6.688,1.615 0.292,0.25 10 false *b

Text in Illustration
*a Rear Side *b Until Pin Stops


Hide 3.REPLACE RING PIN

NOTICE:

It is not necessary to remove a ring pin unless it is being replaced.


a.

Install the ring pins as shown in the illustration.

A385229E01
0.708,0.302 1.021,0.5 0.313,0.198 10 false *a 0.698,2.177 1.01,2.375 0.313,0.198 10 false *c 5.135,0.188 5.448,0.385 0.313,0.198 10 false *b 6.427,3.292 6.74,3.49 0.313,0.198 10 false *d 3.5,2.438 3.813,2.635 0.313,0.198 10 false A 4.76,2.417 5.073,2.615 0.313,0.198 10 false B 2.323,2.635 2.99,3.01 0.667,0.375 10 false 7 mm (0.276 in.) 3.833,2.24 4.5,2.615 0.667,0.375 10 false 8 mm (0.315 in.) 3.219,3.125 3.885,3.5 0.667,0.375 10 false 14.5 mm (0.571 in.) 4.552,3.146 5.219,3.521 0.667,0.375 10 false 11 mm (0.433 in.)

Text in Illustration
*a Front Side *b Cylinder Head Side
*c Rear Side *d Until Pin Stops


Hide 13201A 4.REPLACE CONNECTING ROD SMALL END BUSH

a.
A057244E04
1.271,1.688 1.51,1.688 false 2.354,1.688 1.896,1.688 false 2.438,0.604 2,0.604 false 1.229,0.594 1.594,0.594 false 1.635,0.49 2.031,0.76 0.396,0.271 10 false SST 1.552,1.573 1.948,1.844 0.396,0.271 10 false SST

Using SST and a press, press out the bushing.

SST
09222-54011  (09222-03016, 09222-03026, 09222-03021)


b.
A056739

Using a round file, lightly file off any roughness from the small end of the connecting rod.


c.
A057240E04
1.99,0.594 2.375,0.594 false 1.969,1.24 2.365,1.24 false 2.052,1.708 2.365,1.708 false 2.406,0.49 2.573,0.688 0.167,0.198 10 false *1 2.417,1.115 2.594,1.302 0.177,0.188 10 false *2 2.417,1.594 2.802,1.844 0.385,0.25 10 false SST

Attach a new bush to SST with the ball of SST inside the oil hole of the bush.

SST
09222-54011  (09222-03021)

Text in Illustration
*1 Oil Hole
*2 Ball


d.
A056722E05
2.01,0.49 2.615,0.979 2.615,0.979 2.094,1.677 false 2.667,0.865 2.844,1.063 0.177,0.198 10 false *1

Align the oil holes of the bush and connecting rod.

Text in Illustration
*1 Oil Hole


e.
A057245E05
0.875,0.781 0.667,0.781 false 1.125,0.24 1.5,0.24 false 2.396,0.604 1.938,0.26 false 1.135,1.021 1.5,0.833 false 2.5,1.135 1.927,0.823 false 1.177,1.865 1.5,1.688 false 2.323,1.698 1.938,1.698 false 1.563,0.146 1.927,0.396 0.365,0.25 10 false SST 1.563,1.573 1.927,1.823 0.365,0.25 10 false SST 1.563,0.698 1.927,0.948 0.365,0.25 10 false SST 0.396,0.656 0.563,0.844 0.167,0.188 10 false *1

Using SST and a press, press in the bush.

SST
09222-54011  (09222-03016, 09222-03026, 09222-03021)

Text in Illustration
*1 Bush


f.
A057241

Using a pin hole grinder, hone the bush to obtain the clearance between the bush and piston pin.


g.

Check the piston pin fit at normal room temperature.

i.
A057242

Coat the piston pin with engine oil, and push it into the connecting rod with your thumb.