Home › Engine / Hybrid System › 5L-E (ENGINE MECHANICAL) › ENGINE
RM27T0E _51 Engine / Hybrid System _053661 5L-E ENGINE MECHANICAL _0260479 ENGINE G

5L-E ENGINE MECHANICAL  ENGINE  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.INSPECT INJECTION TIMING

a.
A073717E02
3.077,1.411 3.246,1.563 0.170,0.152 10 *1 2.187,0.689 2.776,1.514 2.776,1.514 2.995,1.514 false 2.316,0.672 2.909,1.514 false

Using a mirror, check that the matchmarks of the injection pump flange and timing belt case are aligned.

Text in Illustration
*1 Matchmark


Hide 2.ADJUST INJECTION TIMING

a.
A073718

Loosen the following nuts and bolts.

i.

The bolt holding the injection pump to the injection pump stay.


ii.

The 2 nuts holding the injection pump to the timing belt case.



b.

Align the matchmark by slightly tilting the injection pump.


c.

Tighten the following nuts and bolts.

i.

The 2 nuts holding the injection pump to the timing belt case.

Torque:
21 N*m (209 kgf*cm, 15 ft.*lbf)


ii.

The bolt holding the injection pump to the injection pump stay.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)



Hide 3.INSPECT ENGINE IDLE SPEED

a.

Warm up the engine.


b.

When using the intelligent tester:

i.

Connect the intelligent tester to the DLC3.

Idle speed:

720 to 820 rpm


NOTICE:
·

Turn all the electrical systems and the A/C off.

·

When checking the idling speed, the shift lever should be in neutral.



HINT:

Refer to the intelligent tester operator's manual for further details.




c.
A206183E08
0.073,0.04 0.365,0.234 0.291,0.194 10 *a 0.088,1.78 0.400,1.933 0.312,0.152 10 TAC 0.517,1.862 0.625,1.862 0.625,1.862 1.018,1.469 false

When not using an intelligent tester:

i.

Using SST, connect the tachometer test probe to terminal 9 (TAC) of the DLC3.

SST
09843-18040  


ii.

Check the idle speed.

Standard idle speed:

720 to 820 rpm


Text in Illustration
*a Front View of DLC3

NOTICE:
·

Turn all the electrical systems and the A/C off.

·

When checking the idling speed, the shift lever should be in neutral.

·

Confirm the terminal number before connecting them. Connecting the wrong terminal can be damage the engine.





Hide 4.INSPECT MAXIMUM ENGINE SPEED

a.

Start the engine.


b.

Fully depress the accelerator pedal.


c.

Check the maximum speed.

Maximum engine speed:

4850 to 4950 rpm



Hide 5.INSPECT COMPRESSION

HINT:

If there is a lack of power, excessive oil consumption or poor fuel economy is suspected. Measure the compression pressure.


a.

Warm up and stop the engine.


b.

Remove the glow plugs.


c.

Disconnect the spill control valve connector.


d.

Check the cylinder compression pressure.

i.
A073719E05
0.458,0.115 0.969,0.115 0.969,0.115 1.365,0.792 false 0.021,0.031 0.344,0.208 0.323,0.177 10 false SST

Install SST (attachment) to the glow plug hole.

SST
09992-00026  (09992-00121)

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


ii.
A073720E05
2.031,0.125 2.135,0.125 2.135,0.125 2.417,0.76 false 0.583,0.229 0.688,0.229 0.688,0.229 0.969,0.854 false 1.615,0.031 1.917,0.198 0.302,0.167 10 false SST 0.177,0.135 0.635,0.375 0.458,0.24 10 true SST

Connect SST (compression gauge) to SST (attachment).

SST
09992-00026  (09992-00121, 09992-00211)


iii.

Fully open the throttle valve, and start the engine.


iv.

While cranking the engine, measure the compression pressure.

NOTICE:

This measurement must be done as quickly as possible.


HINT:

Always use a fully charged battery to obtain an engine speed of 250 rpm or more.




e.

Repeat the steps above for each cylinder.

Standard compression pressure:

3138 kPa (32.0 kgf/cm2, 455 psi) or higher


Minimum pressure:

1961 kPa (20.0 kgf/cm2, 284 psi)


Difference between each cylinder:

490 kPa (5.0 kgf/cm2, 71 psi) or less


If the cylinder compression in one or more cylinders is low, pour a small amount of engine oil into the cylinder through the glow plug hole and check the compression pressure for the cylinder with low compression.

HINT:
·

If adding oil helps the compression, the piston rings and/or cylinder bore may be worn or damaged.

·

If the pressure stays low, a valve may be stuck or the seating may be improper, or there may be leakage past the gasket.




f.

Remove SST.


g.

Reinstall the glow plugs.


h.

Reconnect the spill control valve connector.