Home › Engine / Hybrid System › 1GR-FE (ENGINE MECHANICAL) › CYLINDER HEAD
RM27T0E _51 Engine / Hybrid System _053662 1GR-FE ENGINE MECHANICAL _0260497 CYLINDER HEAD A

1GR-FE ENGINE MECHANICAL  CYLINDER HEAD  REPLACEMENT  


PROCEDURE

Hide 11122 1.REPLACE INTAKE VALVE GUIDE BUSH

a.

Heat the cylinder head to 80 to 100°C (176 to 212°F).


b.

Place the cylinder head on wooden blocks.


c.
A222129E05
1.958,0.156 1.833,0.156 1.833,0.156 1.594,0.802 true 1.833,0.156 1.719,1.344 true 1.99,0.073 2.302,0.313 0.313,0.24 10 true SST

Using SST and a hammer, tap out the intake valve guide bushes.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)


d.

Using a caliper gauge, measure the intake valve guide bush bore diameter of the cylinder head.

Standard Bush Bore Diameter:
Item Specified Condition
STD 10.285 to 10.306 mm (0.4049 to 0.4057 in.)
O/S 0.05 10.335 to 10.356 mm (0.4069 to 0.4077 in.)



e.

Select a new valve guide bush.

New Guide Bush:
Item Specified Condition
Bush Bore Diameter 10.285 to 10.306 mm (0.4049 to 0.4057 in.) 10.335 to 10.356 mm (0.4069 to 0.4077 in.)
Use Bush STD O/S 0.05


If the bush bore diameter of the cylinder head is more than 10.306 mm (0.4057 in.), machine the bush bore diameter to 10.335 to 10.356 mm (0.4069 to 0.4077 in.) to install an O/S 0.05 valve guide bush.

If the bush bore diameter of the cylinder head is more than 10.356 mm (0.4077 in.), replace the cylinder head.

New Guide Bush Diameter:
Item Specified Condition
STD 10.333 to 10.344 mm (0.4068 to 0.4072 in.)
O/S 0.05 10.383 to 10.394 mm (0.4088 to 0.4092 in.)


HINT:

Different bushes are used for the intake and exhaust.


Standard bush length:

41.3 to 41.7 mm (1.63 to 1.64 in.)



f.

Heat the cylinder head to 80 to 100°C (176 to 212°F).


g.

Place the cylinder head on wooden blocks.


h.
A221110E01
2.067,0.057 2.384,0.261 0.317,0.204 10 SST 1.591,0.786 1.921,0.143 1.921,0.143 2.035,0.143 false 1.921,0.143 1.711,1.324 false 2.982,0.519 3.161,0.687 0.179,0.168 10 *1

Using SST, tap in the intake valve guide bushes to the specified protrusion height.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)

Protrusion height:

9.10 to 9.90 mm (0.358 to 0.390 in.)


Text in Illustration
*1 Protrusion Height


i.
A131839

Using a sharp 5.5 mm reamer, ream the valve guide bushes to obtain the specified clearance.

Standard oil clearance:

0.025 to 0.060 mm (0.000984 to 0.00236 in.)



Hide 11126 2.REPLACE EXHAUST VALVE GUIDE BUSH

a.

Heat the cylinder head to 80 to 100°C (176 to 212°F).


b.

Place the cylinder head on wooden blocks.


c.
A222130E01
2.957,1.524 3.284,1.731 0.327,0.207 10 SST 2.221,0.539 3.132,1.251 3.132,1.251 3.132,1.502 false 3.132,1.251 2.094,1.1 false

Using SST and a hammer, tap out the exhaust valve guide bushes.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)


d.

Using a caliper gauge, measure the exhaust valve guide bush bore diameter of the cylinder head.

Standard Bush Bore Diameter:
Item Specified Condition
STD 10.285 to 10.306 mm (0.4049 to 0.4057 in.)
O/S 0.05 10.335 to 10.356 mm (0.4069 to 0.4077 in.)



e.

Select a new valve guide bush.

New Guide Bush:
Item Specified Condition
Bush Bore Diameter 10.285 to 10.306 mm (0.4049 to 0.4057 in.) 10.335 to 10.356 mm (0.4069 to 0.4077 in.)
Use Bush STD O/S 0.05


If the bush bore diameter of the cylinder head is more than 10.306 mm (0.4057 in.), machine the bush bore diameter to 10.335 to 10.356 mm (0.4069 to 0.4077 in.) to install an O/S 0.05 valve guide bush.

If the bush bore diameter of the cylinder head is more than 10.356 mm (0.4077 in.), replace the cylinder head.

New Guide Bush Diameter:
Item Specified Condition
STD 10.333 to 10.344 mm (0.4068 to 0.4072 in.)
O/S 0.05 10.383 to 10.394 mm (0.4088 to 0.4092 in.)


HINT:

Different bushes are used for the intake and exhaust.


Standard bush length:

46.8 to 47.2 mm (1.84 to 1.86 in.)



f.

Heat the cylinder head to 80 to 100°C (176 to 212°F).


g.

Place the cylinder head on wooden blocks.


h.
A221111E06
2.229,0.573 3.146,1.281 3.146,1.281 3.146,1.552 true 3.146,1.281 2.094,1.146 true 0.302,1.281 0.49,1.458 0.188,0.177 10 true *1 3.01,1.594 3.344,1.792 0.333,0.198 10 false SST

Using SST, tap in the exhaust valve guide bushes to the specified protrusion height.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)

Protrusion height:

9.10 to 9.90 mm (0.358 to 0.390 in.)


Text in Illustration
*1 Protrusion Height


i.
A096429

Using a sharp 5.5 mm reamer, ream the valve guide bushes to obtain the specified clearance.

Standard oil clearance:

0.030 to 0.065 mm (0.00118 to 0.00256 in.)



Hide 3.REPLACE UNION

a.

Remove the union from the bank 1 cylinder head (front side) and bank 2 cylinder head (intake port side).

A222133E01
0.198,0.001 0.425,0.208 0.228,0.207 10 *A 3.969,0.001 4.197,0.208 0.228,0.207 10 *B 2.189,2.131 3.289,2.342 1.100,0.211 10 67 mm (2.64 in.) 5.851,2.137 6.951,2.349 1.100,0.211 10 30 mm (1.18 in.)

Text in Illustration
*A Front Side of RH *B Intake Side of LH


b.

Apply adhesive to 2 or 3 threads of the bolt ends of new unions.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



c.

Using a 12 mm deep socket wrench, install the 2 unions.

Torque:
15 N*m (150 kgf*cm, 11 ft.*lbf)


Hide 4.REPLACE TIGHT PLUG

NOTICE:

If coolant leaks from a tight plug or a plug is corroded, replace it.


a.

Remove the tight plugs.


b.

Apply adhesive around new tight plugs.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



c.

Using SST and a hammer, tap in the tight plugs to the standard depth.

A222132E01
1.428,0.043 1.621,0.241 0.193,0.198 10 *A 5.602,0.043 5.795,0.241 0.193,0.198 10 *B 2.256,2.154 2.449,2.351 0.193,0.198 10 *1 3.951,3.384 4.332,3.574 0.381,0.190 10 SST 5.047,2.39 5.047,3.065 5.047,3.065 4.095,3.065 false 4.095,1.98 4.095,3.352 false

SST
09950-60010  (09951-00250)
09950-70010  (09951-07150)

Standard depth:

1.7 to 2.7 mm (0.0669 to 0.106 in.)


Text in Illustration
*A RH *B LH
*1 Standard Depth - -


Hide 5.REPLACE STRAIGHT PIN

NOTICE:

If a straight pin is deformed, replace it.


a.

Using a plastic-faced hammer, tap in new straight pins as shown in the illustration.

A221114E01
0.043,0 0.260,0.198 0.217,0.198 10 *A 2.809,0 3.026,0.198 0.217,0.198 10 *B 6.172,0.757 6.389,0.954 0.217,0.198 10 *1

Protrusion height:

18.0 to 19.0 mm (0.708 to 0.748 in.)


Text in Illustration
*A RH *B LH
*1 Protrusion Height - -


Hide 6.REPLACE RING PIN

NOTICE:

It is not necessary to remove a ring pin unless it is being replaced.


a.
A221112E01
0.064,0 0.248,0.186 0.185,0.186 10 *A 0.064,1.999 0.248,2.185 0.185,0.186 10 *B 1.529,3.832 1.714,4.018 0.185,0.186 10 *1

Using a plastic-faced hammer, tap in new ring pins to the specified protrusion height.

Protrusion height:

2.5 to 3.5 mm (0.0984 to 0.138 in.)


Text in Illustration
*A RH
*B LH
*1 Protrusion Height


Hide 7.REPLACE SPARK PLUG TUBE

A223702E01
1.354,0.221 1.542,0.402 0.188,0.181 10 *1 1.507,1.894 1.695,2.075 0.188,0.181 10 *2 1.57,0.303 1.705,0.303 1.705,0.303 1.971,0.596 false

HINT:

When using a new cylinder head, the spark plug tubes must be replaced.


a.

Remove the spark plug tube.

Text in Illustration
*1 Adhesive
*2 Distance


b.

Apply adhesive to the end of a new spark plug tube.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.


Standard seal diameter:

1.0 to 3.0 mm (0.394 to 0.118 in.)


Distance:

9.0 to 15.0 mm (0.354 to 0.590 in.)


NOTICE:
·

Be careful not to deform the spark plug tube.

·

Be careful not to expose the seal to coolant for at least 1 hour after installing it.




c.
A223701E01
2.784,3.057 3.019,3.268 0.235,0.211 10 *1 1.13,3.255 1.365,3.466 0.235,0.211 10 *2 2.213,3.626 2.508,3.161 2.508,3.161 2.754,3.161 false

Using a wooden block and hammer, tap in the spark plug tube to the specified protrusion height.

Standard protrusion height:

75.1 to 76.1 mm (2.96 to 3.00 in.)


Text in Illustration
*1 Cylinder Head Top Surface
*2 Protrusion Height

NOTICE:

To avoid tapping in the spark plug tube too far, measure the protrusion height while tapping it.