Home › Engine / Hybrid System › 2TR-FE (ENGINE MECHANICAL) › ENGINE UNIT
RM27T0E _51 Engine / Hybrid System _053663 2TR-FE ENGINE MECHANICAL _0260500 ENGINE UNIT G

2TR-FE ENGINE MECHANICAL  ENGINE UNIT  INSPECTION  


PROCEDURE

Hide 13506 1.INSPECT CHAIN SUB-ASSEMBLY

a.
A101905E08
0.635,1.771 0.76,1.969 0.125,0.198 10 false 1 0.823,1.781 0.948,1.979 0.125,0.198 10 false 2 1.01,1.781 1.125,1.979 0.115,0.198 10 false 3 1.177,1.781 1.313,1.979 0.135,0.198 10 false 4 1.552,1.781 1.688,1.979 0.135,0.198 10 false 6 2.927,1.771 3.156,1.969 0.229,0.198 10 false 16 1.365,1.781 1.5,1.979 0.135,0.198 10 false 5 1.74,1.073 1.927,1.271 0.188,0.198 10 false *a

Pull the chain sub-assembly with a force of 147 N (15 kgf, 33.0 lbf) as shown in the illustration.


b.

Using a vernier caliper, measure the length of 16 links.

Maximum chain elongation:

147.5 mm (5.81 in.)


Text in Illustration
*a Measuring Area

If the elongation is more than the maximum, replace the chain sub-assembly.

NOTICE:

Perform the measurement at 3 random places.



Hide 13507 2.INSPECT NO. 2 CHAIN SUB-ASSEMBLY

a.

Pull the No. 2 chain sub-assembly with a force of 147 N (15 kgf, 33.0 lbf).


b.

Using a vernier caliper, measure the length of 16 links.

Maximum chain elongation:

123.6 mm (4.87 in.)


If the elongation is more than the maximum, replace the No. 2 chain sub-assembly.

NOTICE:

Perform the measurement at 3 random places.



Hide 13540 3.INSPECT NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A097905E21
2.229,0.813 2.458,0.469 2.458,0.469 2.531,0.469 true 1.458,1.573 1.729,1.854 1.729,1.854 1.854,1.854 true 2.563,0.365 2.802,0.594 0.24,0.229 10 false *a 1.896,1.75 2.115,1.948 0.219,0.198 10 false *b

Move the stopper plate upward to release the lock. Push the plunger and check that it moves smoothly.

Text in Illustration
*a Plunger
*b Stopper Plate


Hide 13550 4.INSPECT NO. 2 CHAIN TENSIONER ASSEMBLY

a.
A101971E05
0.883,1.164 0.646,0.726 0.646,0.726 0.539,0.726 false 1.461,0.601 1.69,0.162 1.69,0.162 1.845,0.162 false 0.324,0.633 0.513,0.805 0.188,0.172 10 *a 1.864,0.064 2.052,0.236 0.188,0.172 10 *b

Move the stopper plate downward to release the lock. Push the plunger and check that it moves smoothly.

Text in Illustration
*a Plunger
*b Stopper Plate


Hide 13050 5.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY

a.
A337680

Measure the distance between the most worn out camshaft timing gear tip and the beginning of the worn area below the tip.

Minimum distance:

1.0 mm (0.0394 in.)


Text in Illustration
V100145

Worn Area

If the distance is less than the minimum, replace the camshaft timing gear assembly.

If the worn area is too small or difficult to distinguish from a normal area, perform the following 2 steps.


b.

Wrap the chain sub-assembly around the camshaft timing gear assembly.


c.

Using a vernier caliper, measure the sprocket diameter with the chain sub-assembly.

Minimum sprocket diameter (with chain):

113.8 mm (4.48 in.)


HINT:

The vernier caliper must contact the chain rollers for the measurement.


If the diameter is less than the minimum, replace the chain sub-assembly and camshaft timing gear assembly.


Hide 13070A 6.INSPECT CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

a.
A337679

Measure the distance between the most worn out camshaft timing gear tip and the beginning of the worn area below the tip.

Minimum distance:

1.0 mm (0.0394 in.)


Text in Illustration
V100145

Worn Area

If the distance is less than the minimum, replace the camshaft timing exhaust gear assembly.

If the worn area is too small or difficult to distinguish from a normal area, perform the following 2 steps.


b.

Wrap the chain sub-assembly around the camshaft timing exhaust gear assembly.


c.

Using a vernier caliper, measure the sprocket diameter with the chain sub-assembly.

Minimum sprocket diameter (with chain):

113.8 mm (4.48 in.)


HINT:

The vernier caliper must contact the chain rollers for the measurement.


If the diameter is less than the minimum, replace the chain sub-assembly and camshaft timing exhaust gear assembly.


Hide 13521 7.INSPECT CRANKSHAFT TIMING GEAR

a.
A097908E06
1.917,1.771 2.073,1.969 0.156,0.198 10 false .

Measure the distance between the most worn out crankshaft timing gear tip and the beginning of the worn area below the tip.

Minimum distance:

1.0 mm (0.0394 in.)


Text in Illustration
V100145

Worn Area

If the distance is less than the minimum, replace the crankshaft timing gear.

If the worn area is too small or difficult to distinguish from a normal area, perform the following 2 steps.


b.

Wrap the chain sub-assembly around the crankshaft timing gear.


c.

Using a vernier caliper, measure the sprocket diameter with the chain sub-assembly.

Minimum sprocket diameter (with chain):

59.4 mm (2.34 in.)


HINT:

The vernier caliper must contact the chain rollers for the measurement.


If the diameter is less than the minimum, replace the chain sub-assembly and crankshaft timing gear.


Hide 13559 8.INSPECT CHAIN TENSIONER SLIPPER

a.
A361075E01
1.521,0.823 1.719,1.01 0.198,0.188 10 false *a

Using a vernier caliper, measure the chain tensioner slipper wear.

Maximum wear:

2.0 mm (0.0787 in.)


Text in Illustration
*a Wear

If the wear is more than the maximum, replace the chain tensioner slipper.


Hide 13561 9.INSPECT NO. 1 CHAIN VIBRATION DAMPER

a.
A361074E01
1.74,0.802 1.969,1 0.229,0.198 10 false *a

Using a vernier caliper, measure the No. 1 chain vibration damper wear.

Maximum wear:

2.0 mm (0.0787 in.)


Text in Illustration
*a Wear

If the wear is more than the maximum, replace the No. 1 chain vibration damper.


Hide 13566B 10.INSPECT TIMING CHAIN GUIDE

a.
A097911E09
1.698,0.719 1.854,0.917 0.156,0.198 10 false .

Using a vernier caliper, measure the timing chain guide wear.

Maximum wear:

0.5 mm (0.0197 in.)


Text in Illustration
V100145

Wear

If the wear is more than the maximum, replace the timing chain guide.


Hide 13597 11.INSPECT NO. 2 CRANKSHAFT TIMING SPROCKET

a.

Wrap the chain around the No. 2 crankshaft timing sprocket.


b.
A101907

Using a vernier caliper, measure the sprocket diameter with the chain.

Minimum sprocket diameter (with chain):

96.7 mm (3.81 in.)


HINT:

The vernier caliper must contact the chain rollers for the measurement.


If the diameter is less than the minimum, replace the No. 2 chain sub-assembly and No. 2 crankshaft timing sprocket.


Hide 13063 12.INSPECT BALANCESHAFT DRIVE GEAR SUB-ASSEMBLY

a.

Wrap the No. 2 chain sub-assembly around the balanceshaft drive gear sub-assembly.


b.
A101906

Using a vernier caliper, measure the sprocket diameter with the No. 2 chain sub-assembly.

Minimum sprocket diameter (with chain):

75.9 mm (2.99 in.)


HINT:

The vernier caliper must contact the chain rollers for the measurement.


If the diameter is less than the minimum, replace the No. 2 chain sub-assembly and balanceshaft drive gear sub-assembly.


Hide 13562 13.INSPECT NO. 2 CHAIN VIBRATION DAMPER

a.
A101337E07
1.76,1.406 1.979,1.615 0.219,0.208 10 false *a

Using a vernier caliper, measure the No. 2 chain vibration damper wear.

Maximum wear:

1.0 mm (0.0394 in.)


Text in Illustration
*a Wear

If the wear is more than the maximum, replace the No. 2 chain vibration damper.


Hide 13563 14.INSPECT NO. 3 CHAIN VIBRATION DAMPER

a.
A068741E10
1.594,1.115 1.802,1.323 0.208,0.208 10 false *a

Using a vernier caliper, measure the No. 3 chain vibration damper wear.

Maximum wear:

1.0 mm (0.0394 in.)


Text in Illustration
*a Wear

If the wear is more than the maximum, replace the No. 3 chain vibration damper.


Hide 13554 15.INSPECT NO. 4 CHAIN VIBRATION DAMPER

a.
A068742E10
1.563,1.063 1.781,1.26 0.219,0.198 10 false *a

Using a vernier caliper, measure the No. 4 chain vibration damper wear.

Maximum wear:

1.0 mm (0.0394 in.)


Text in Illustration
*a Wear

If the wear is more than the maximum, replace the No. 4 chain vibration damper.


Hide 11101A 16.INSPECT CYLINDER HEAD SET BOLT

a.
A170594E04
2.045,1.227 2.243,1.434 0.198,0.207 10 *a 2.645,1.227 2.842,1.434 0.198,0.207 10 *b

Using a vernier caliper, measure the diameter of the most elongated threads in the measuring area.

Standard outside diameter:

10.76 to 10.97 mm (0.424 to 0.432 in.)


Minimum outside diameter:

10.40 mm (0.409 in.)


Distance:

30 mm (1.18 in.)


Text in Illustration
*a Measuring area
*b Distance

If a visual check reveals no excessively thin areas, check the center of the measuring area (see illustration) and find the area that has the smallest diameter.

If the diameter is less than the minimum, replace the cylinder head bolt.


Hide 13750 17.INSPECT VALVE LASH ADJUSTER ASSEMBLY

NOTICE:
·

Keep the lash adjuster free from dirt and foreign objects.

·

Only use clean engine oil.



a.
A302788E03
0.938,3.042 1.094,3.042 1.094,3.042 1.417,3.406 false 1.073,2.417 1.406,2.302 1.406,2.302 1.573,2.302 true 0.885,2.271 1.385,1.979 1.385,1.979 1.552,1.979 true 0.969,1.802 1.385,1.625 1.385,1.625 1.552,1.625 true 1.104,1.333 1.385,1.271 1.385,1.271 1.563,1.271 false 1.083,1.146 1.385,0.823 1.385,0.823 1.563,0.823 false 1.073,0.615 1.313,0.406 1.313,0.406 1.479,0.406 false 2.427,0.604 2.073,0.406 2.073,0.406 1.906,0.406 false 2.406,1.031 2.01,0.823 2.01,0.823 1.833,0.823 false 2.365,1.323 2.01,1.271 2.01,1.271 1.844,1.271 false 2.458,1.76 2.01,1.646 2.01,1.646 1.833,1.646 true 2.594,2.24 2.021,1.969 2.021,1.969 1.823,1.969 true 2.396,2.406 2.01,2.302 2.01,2.302 1.833,2.302 true 1.552,0.323 1.885,0.51 0.333,0.188 10 false SST 0.771,2.573 0.969,2.771 0.198,0.198 10 false *a 2.542,2.583 2.74,2.781 0.198,0.198 10 false *b 1.615,0.719 1.813,0.917 0.198,0.198 10 false *c 1.615,1.177 1.813,1.375 0.198,0.198 10 false *d 1.615,1.542 1.813,1.74 0.198,0.198 10 false *e 1.615,1.896 1.813,2.094 0.198,0.198 10 false *f 1.615,2.188 1.813,2.385 0.198,0.198 10 false *g 0.604,2.948 0.938,3.146 0.333,0.198 10 false SST

Place the lash adjuster into a container full of new engine oil.

Text in Illustration
*a CORRECT
*b INCORRECT
*c Taper Part
*d Plunger
*e Low Pressure Chamber
*f Check Ball
*g High Pressure Chamber


b.

Insert the tip of SST into the lash adjuster plunger and use the tip to press down on the check ball inside the plunger.

SST
09276-75010  


c.

Squeeze SST and the lash adjuster together to move the plunger up and down 5 to 6 times.


d.

Check the movement of the plunger and bleed air.

OK:

Plunger moves up and down.


NOTICE:

When bleeding high-pressure air from the compression chamber, make sure that the tip of SST is actually pressing the check ball as shown in the illustration. If the check ball is not pressed, air will not bleed.



e.

After bleeding the air, remove SST. Then try to quickly and firmly press the plunger with your fingers.

OK:

Plunger can be pressed 3 times.


If the plunger can still be compressed after pressing it 3 times, replace the valve lash adjuster with a new one.


Hide 13511 18.INSPECT CAMSHAFT

a.

Check the camshaft runout.

i.

Place the camshaft on V-blocks.


ii.

Using a dial indicator, measure the circle runout at the center journal.

Maximum circle runout:

0.03 mm (0.00118 in.)


If the circle runout is more than the maximum, replace the camshaft.



b.

Using a micrometer, measure the cam lobe height.

Standard cam lobe height:

42.855 to 42.955 mm (1.687 to 1.691 in.)


Minimum cam lobe height:

42.855 mm (1.687 in.)


If the cam lobe height is less than the minimum, replace the camshaft.


c.

Using a micrometer, measure the journal diameter.

Standard Journal Diameter:
Item Specified Condition
No. 1 journal 35.949 to 35.965 mm (1.415 to 1.416 in.)
Other journal 26.959 to 26.975 mm (1.061 to 1.062 in.)


If the journal diameter is not as specified, check the oil clearance.


Hide 13512 19.INSPECT NO. 2 CAMSHAFT

a.

Check the No. 2 camshaft runout.

i.

Place the No. 2 camshaft on V-blocks.


ii.

Using a dial indicator, measure the circle runout at the center journal.

Maximum circle runout:

0.03 mm (0.00118 in.)


If the circle runout is more than the maximum, replace the No. 2 camshaft.



b.

Using a micrometer, measure the cam lobe height.

Standard cam lobe height:

42.854 to 42.954 mm (1.687 to 1.691 in.)


Minimum cam lobe height:

42.854 mm (1.687 in.)


If the cam lobe height is less than the minimum, replace the No. 2 camshaft.


c.

Using a micrometer, measure the journal diameter.

Standard Journal Diameter:
Item Specified Condition
No. 1 journal 35.949 to 35.965 mm (1.415 to 1.416 in.)
Other journal 26.959 to 26.975 mm (1.061 to 1.062 in.)


If the journal diameter is not as specified, check the oil clearance.


Hide 17141 22.INSPECT EXHAUST MANIFOLD

a.
A222420

Using a precision straightedge and feeler gauge, measure the warpage of the surface that contacts the cylinder head.

Maximum warpage:

0.7 mm (0.0276 in.)


If the warpage is more than the maximum, replace the exhaust manifold.