Home › Engine / Hybrid System › 2TR-FE (ENGINE MECHANICAL) › CYLINDER BLOCK
RM27T0E _51 Engine / Hybrid System _053663 2TR-FE ENGINE MECHANICAL _0260502 CYLINDER BLOCK A

2TR-FE ENGINE MECHANICAL  CYLINDER BLOCK  REPLACEMENT  


PROCEDURE

Hide 13201A 1.REPLACE CONNECTING ROD SMALL END BUSH

a.
A054717E14
0.76,0.469 1.063,0.635 0.302,0.167 10 false SST

Using SST and a press, press out the bush.

SST
09222-30010  


b.
A054732E21
2.177,0.813 2.552,1.177 2.552,1.177 2.25,1.583 true 2.604,1.052 2.833,1.281 0.229,0.229 10 false *a

Align the oil holes of a new bush and the connecting rod.

Text in Illustration
*a Oil Hole


c.
A054717E13
0.771,0.448 1.115,0.656 0.344,0.208 10 false SST

Using SST and a press, press in the bush.

SST
09222-30010  


d.
A054733E04
1.802,1.281 1.958,1.479 0.156,0.198 10 false .

Using a pin hole grinder, hone the bush to obtain the standard specified clearance between the bush and piston pin.


e.

Check that the piston pin fits at normal room temperature.

i.

Coat the piston pin with engine oil and push it into the connecting rod with your thumb.



Hide 2.REPLACE TIGHT PLUG

NOTICE:

If coolant leaks from the tight plug or the plug is corroded, replace it.


A103432E06
1.726,1.976 1.911,2.152 0.185,0.176 10 *a 1.628,4.303 1.873,4.460 0.245,0.157 10 *c 4.839,1.976 5.040,2.161 0.201,0.185 10 *b 4.813,4.303 5.037,4.458 0.223,0.155 10 *d 4.843,3.92 4.954,4.066 0.111,0.146 10 A 1.671,5.892 1.793,6.037 0.122,0.146 10 D 1.816,3.546 1.969,3.714 0.153,0.168 10 B 3.32,0.586 3.704,0.867 0.384,0.281 10 SST 2.51,0.741 3.286,0.667 3.286,0.667 2.173,0.65 false 1.862,2.793 1.862,3.545 false 4.11,2.875 4.889,3.915 4.889,3.915 4.628,2.8 false 5.147,2.8 4.889,3.915 4.889,3.915 5.669,2.875 false 4.155,5.102 4.905,6.161 4.905,6.161 4.66,5.102 false 5.177,5.102 4.905,6.161 4.905,6.161 5.771,5.044 false 1.712,5.172 1.712,5.88 1.712,5.88 2.137,5.58 false 1.312,5.497 1.712,5.88 false 4.851,6.16 4.972,6.304 0.121,0.144 10 C 5.002,1.308 5.199,1.502 0.196,0.194 10 *e

Text in Illustration
*a Front Side *b Intake Side
*c Rear Side *d Exhaust Side
*e 1.0 mm (0.0394 in.) - -

a.

Apply adhesive to new tight plugs.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.



b.

Using SST, tap in the 8 tight plugs labeled A and C.

SST
09950-60010  (09951-00350)
09950-70010  (09951-07100)


c.

Using SST, tap in the tight plug labeled B.

SST
09950-60010  (09951-00300)
09950-70010  (09951-07100)


d.

Using SST, tap in the 3 tight plugs labeled D.

SST
09950-60010  (09951-00400)
09950-70010  (09951-07100)


Hide 3.REPLACE STRAIGHT PIN

NOTICE:

It is not necessary to remove a straight pin unless it is being replaced.


a.
A101513E07
2.052,0.656 2.813,0.656 false 1.302,1.771 1.802,1.906 1.802,1.906 2.271,1.781 false 0.635,2.042 0.354,2.042 false 0.198,1.958 0.313,2.104 0.115,0.146 10 false A 1.771,1.969 1.906,2.125 0.135,0.156 10 false B 1.406,2.469 1.583,2.635 0.177,0.167 10 false *b 2.646,2.573 2.823,2.74 0.177,0.167 10 false *b 0.125,0.073 0.313,0.25 0.188,0.177 10 false *a 2.875,0.573 3.021,0.729 0.146,0.156 10 false A 2.229,3 2.365,3.167 0.135,0.167 10 false B 0.844,3 1.021,3.208 0.177,0.208 10 true A

Using a plastic-faced hammer, tap in new straight pins to the cylinder block.

Standard Straight Pin:
Item Wide Protrusion
Pin A 10 mm (0.394 in.) 13 mm (0.512 in.)
Pin B 6.0 mm (0.236 in.) 5.5 mm (0.217 in.)


Text in Illustration
*a Rear Side
*b Protrusion


Hide 4.REPLACE RING PIN

NOTICE:

It is not necessary to remove a ring pin unless it is being replaced.

A101514E08
1.323,1.292 0.458,1.646 0.458,1.646 0.938,2.125 false 2.531,2.135 2.844,2.135 false 6.5,0.74 6.927,1.625 6.927,1.625 6.5,2.365 false 0.458,4.625 1.698,5.354 1.698,5.354 3.177,3.969 false 1.75,0.219 2,0.396 0.25,0.177 10 false *a 5.083,0.313 5.333,0.49 0.25,0.177 10 false *b 1.677,2.969 1.938,3.167 0.26,0.198 10 false *c 0.292,1.552 0.469,1.729 0.177,0.177 10 false A 4.375,4.063 4.5,4.229 0.125,0.167 10 false A 4.375,5.573 4.5,5.74 0.125,0.167 10 false B 5.927,4.365 6.063,4.521 0.135,0.156 10 false C 6.979,1.552 7.125,1.729 0.146,0.177 10 false C 1.667,5.406 1.792,5.563 0.125,0.156 10 false B 2.906,2.042 3.042,2.208 0.135,0.167 10 false A 4.865,3.781 5.042,3.958 0.177,0.177 10 false *d 6.417,3.938 6.594,4.115 0.177,0.177 10 false *d 4.854,5.24 5.031,5.417 0.177,0.177 10 false *d 4.354,4.938 4.531,5.115 0.177,0.177 10 false *e 4.354,3.5 4.531,3.677 0.177,0.177 10 false *e 5.896,3.594 6.073,3.771 0.177,0.177 10 false *e 4.865,4.51 5.042,4.688 0.177,0.177 10 false *f 4.865,3.083 5.042,3.26 0.177,0.177 10 false *f 6.417,3.125 6.594,3.302 0.177,0.177 10 false *f


Text in Illustration
*a Front Side *b Lower Side
*c Upper Side *d Height
*e Width *f Protrusion

a.

Using a plastic-faced hammer, tap in new ring pins to the cylinder block.

Standard Ring Pin:
Item Height Width Protrusion
Pin A 9.0 mm (0.354 in.) 11 mm (0.433 in.) 3.5 to 4.5 mm (0.138 to 0.177 in.)
Pin B 14 mm (0.511 in.) 15 mm (0.591 in.) 7.5 to 9.5 mm (0.295 to 0.374 in.)
Pin C 20 mm (0.787 in.) 14 mm (0.511 in.) 7.0 to 9.0 mm (0.276 to 0.354 in.)