Home › Engine / Hybrid System › 2TR-FE (ENGINE MECHANICAL) › CYLINDER BLOCK
RM27T0E _51 Engine / Hybrid System _053663 2TR-FE ENGINE MECHANICAL _0260502 CYLINDER BLOCK A

2TR-FE ENGINE MECHANICAL  CYLINDER BLOCK  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repairs" after replacing the piston sub-assembly or piston ring (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).


PROCEDURE

Hide 1.INSTALL STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.

U147684E03
4.115,0.656 4.406,0.313 4.406,0.313 4.51,0.313 true 2.406,0.635 2.854,0.188 2.854,0.188 3.042,0.188 false 5.573,0.656 5.865,0.313 5.865,0.313 5.969,0.313 true 2.188,1.438 2.844,1.146 2.844,1.146 2.969,1.146 false 2.208,1.625 2.854,1.146 false 1.854,4.135 2.594,3.063 2.594,3.063 2.719,3.063 false 0.792,0.125 1.01,0.333 0.219,0.208 10 false *a 0.406,2.885 0.635,3.094 0.229,0.208 10 false *c 3.938,0.125 4.146,0.323 0.208,0.198 10 false *b 3.094,0.104 3.354,0.375 0.26,0.271 10 false A 4.552,0.229 4.729,0.427 0.177,0.198 10 false D 6.021,0.229 6.198,0.427 0.177,0.198 10 false D 0.708,7.417 0.927,7.625 0.219,0.208 10 false B 3.083,7.427 3.26,7.656 0.177,0.229 10 false C 5,5.281 5.135,5.438 0.135,0.156 10 false A 5.25,7.438 5.448,7.635 0.198,0.198 10 false D 3.021,1.063 3.229,1.271 0.208,0.208 10 false B 2.781,2.969 3,3.198 0.219,0.229 10 false C 5.385,2.948 5.583,3.135 0.198,0.188 10 false *d 1.073,6.031 1.271,6.219 0.198,0.188 10 false *f 1.833,6.417 2.031,6.604 0.198,0.188 10 false *g 3.458,5.802 3.656,5.99 0.198,0.188 10 false *h 4.219,6.396 4.417,6.583 0.198,0.188 10 false *i 5.625,6.563 5.823,6.75 0.198,0.188 10 false *j 5.375,4.958 5.573,5.146 0.198,0.188 10 false *d 6.146,3.917 6.344,4.104 0.198,0.188 10 false *e 1.073,7.083 1.271,7.271 0.198,0.188 10 false *d 3.448,7.104 3.646,7.292 0.198,0.188 10 false *d 6.375,6.802 6.573,6.99 0.198,0.188 10 false *k 5.625,7.094 5.823,7.281 0.198,0.188 10 false *l


Text in Illustration
*a Front Side *b Lower Side
*c Exhaust Side *d 12 mm (0.472 in.)
*e 85 mm (3.35 in.) *f 25 mm (0.984 in.)
*g 55 mm (2.17 in.) *h 18 mm (0.709 in.)
*i 60 mm (2.36 in.) *j 20 mm (0.787 in.)
*k 35 mm (1.38 in.) *l 13 mm (0.512 in.)

a.

Using an E8 "TORX" socket wrench, install the stud bolts labeled A.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


b.

Using an E7 "TORX" socket wrench, install the stud bolts labeled B and D.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


c.

Apply adhesive to the hole for the stud bolt labeled C in the cylinder block. Using an E7 "TORX" socket wrench, install the stud bolt labeled C.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)

HINT:

When reusing a stud bolt, apply adhesive to the bolt before installing it.


Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



Hide 11415 2.INSTALL CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY

a.

Apply adhesive to the drain cock.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



b.
A101347E08
1.823,3.802 1.656,4.229 1.656,4.229 1.542,4.229 false 1.74,3.708 1.438,3.479 1.438,3.479 1.333,3.479 false 1.958,3.719 2.26,3.865 2.26,3.865 2.385,3.865 false 1.573,2.792 1.75,3 0.177,0.208 10 false *a 2.115,3.271 2.323,3.458 0.208,0.188 10 false *b 1.083,3.417 1.333,3.615 0.25,0.198 10 false 30° 2.458,3.76 2.729,3.948 0.271,0.188 10 false 60° 1.313,4.135 1.51,4.323 0.198,0.188 10 false *c 1.906,3.854 2.125,4.042 0.219,0.188 10 false *d

Install the cylinder block water drain cock as shown in the illustration.

Torque:
25 N*m (250 kgf*cm, 18 ft.*lbf)

Text in Illustration
*a Upper Side
*b Front
*c Allowable Range
*d Target Direction

NOTICE:
·

Do not rotate the drain cock more than 1 revolution (360°) after tightening the drain cock to the specified torque.

·

Do not loosen the drain cock to adjust it. If an adjustment is necessary, remove the drain cock and reinstall it.




c.

Install the water drain cock plug to the water drain cock sub-assembly.

Torque:
13 N*m (130 kgf*cm, 9 ft.*lbf)


Hide 15708 3.INSTALL NO. 1 OIL NOZZLE SUB-ASSEMBLY

a.
U147462

Using a 5 mm hexagon wrench, install the oil nozzles.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


Hide 13633 4.INSTALL NO. 2 BALANCESHAFT DRIVEN GEAR

a.

Mount the head portion of the balanceshaft in a vise.

NOTICE:

Do not damage the balanceshaft.



b.
A101523E03
0.494,0.995 0.665,1.169 0.171,0.174 10 *1 1.861,0.042 2.058,0.232 0.197,0.190 10 *2 0.751,0.795 0.603,1 false 1.683,0.444 1.849,0.17 false

Install the No. 2 balanceshaft thrust washer and No. 2 balanceshaft driven gear.

Text in Illustration
*1 No. 2 Balanceshaft Driven Gear
*2 No. 2 Balanceshaft Thrust Washer


c.

Install the bolt.

Torque:
36 N*m (367 kgf*cm, 27 ft.*lbf)


Hide 13622 5.INSTALL NO. 2 BALANCESHAFT

a.
A101522

Install the balanceshaft to the cylinder block.

NOTICE:

When installing the balanceshaft, be sure to support the balanceshaft with both hands and avoid scratching the balanceshaft bearing on the cylinder block.



b.
A101521

Install the 2 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 13632 6.INSTALL NO. 1 BALANCESHAFT DRIVEN GEAR

a.

Mount the head portion of the balanceshaft in a vise.

NOTICE:

Do not damage the balanceshaft.



b.
A101520E09
0.615,0.594 0.458,0.802 false 0.635,0.198 1.021,0.198 false 1.094,0.854 1.042,1.052 false 1.896,0.417 2.042,0.208 false 0.354,0.833 0.531,1.063 0.177,0.229 10 false *1 0.948,1.073 1.156,1.302 0.208,0.229 10 false *4 2.073,0.094 2.281,0.271 0.208,0.177 10 false *3 1.052,0.125 1.25,0.354 0.198,0.229 10 false *2

Install the No. 1 balanceshaft thrust washer, balanceshaft thrust spacer, sliding key and No. 1 balanceshaft driven gear.

Text in Illustration
*1 No. 1 Balanceshaft Driven Gear
*2 Sliding Key
*3 Balanceshaft Thrust Washer
*4 Balanceshaft Thrust Spacer


c.

Install the bolt.

Torque:
36 N*m (367 kgf*cm, 27 ft.*lbf)


Hide 13621 7.INSTALL NO. 1 BALANCESHAFT

a.
A101519

Install the No. 1 balanceshaft to the cylinder block.

NOTICE:

When installing the balanceshaft, be sure to support the balanceshaft with both hands and avoid scratching the balanceshaft bearing on the cylinder block.



b.
A101518

Install the bolt.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 13101 8.INSTALL PISTON WITH PIN SUB-ASSEMBLY

HINT:

Perform "Inspection After Repairs" after replacing the piston sub-assembly (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).


a.

Assemble the piston and connecting rod.

i.
A103205E07
2.854,1.302 3.051,1.506 0.197,0.205 10 *a 2.411,1.52 2.667,1.402 2.667,1.402 2.819,1.402 false

Using a screwdriver, install a new snap ring at one end of the piston pin hole.

Text in Illustration
*a Service Hole

HINT:

Make sure that the end gap of the snap ring is not aligned with the service hole cutout portion of the piston.



ii.

Gradually heat the piston to approximately 80 to 90°C (176 to 194°F).


iii.

Coat the piston pin with engine oil.


iv.
A101516E04
1.072,0.078 1.273,0.297 0.201,0.219 10 *a 1.106,1.514 1.331,1.744 0.224,0.230 10 *a 1.76,0.442 1.358,0.199 1.358,0.199 1.301,0.199 false 1.896,1.826 1.399,1.634 1.399,1.634 1.328,1.634 false

Align the front marks of the piston and connecting rod and push in the piston pin with your thumb.

Text in Illustration
*a Front Mark

HINT:

The piston and pin are a matched set.



v.
A101515E10
2.807,1.237 3.007,1.416 0.200,0.180 10 *a 2.43,1.544 2.681,1.317 2.681,1.317 2.764,1.317 false

Using a screwdriver, install a new snap ring at the other end of the piston pin hole.

Text in Illustration
*a Service Hole

HINT:

Make sure that the end gap of the snap ring is not aligned with the service hole cutout portion of the piston.



vi.

Check the fitting condition between the piston and piston pin by trying to move the piston back and forth on the piston pin.



Hide 13011 9.INSTALL PISTON RING SET

HINT:

Perform "Inspection After Repairs" after replacing the piston ring (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).


a.
A164414E07
1.99,1.104 2.542,1.104 false 1.896,1.385 2.271,1.74 2.271,1.74 2.448,1.74 false 1.917,0.906 2.271,0.531 2.271,0.531 2.438,0.531 false 2.5,0.448 2.698,0.635 0.198,0.188 10 false *1 2.521,1.656 2.719,1.844 0.198,0.188 10 false *3 2.583,1.021 2.781,1.208 0.198,0.188 10 false *2

Install the oil ring expander and 2 oil ring side rails by hand.

Text in Illustration
*1 Upper Oil Ring Side Rail
*2 Oil Ring Expander
*3 Lower Oil Ring Side Rail


b.
A149044E07
1.188,1.167 1.74,1.99 1.74,1.99 2.24,0.958 false 1.677,2.063 1.875,2.24 0.198,0.177 10 false *a 0.75,2.656 0.969,2.844 0.219,0.188 10 false *1 2.406,2.656 2.615,2.854 0.208,0.198 10 false *2

Using a piston ring expander, install the 2 compression rings so that the painted marks are positioned as shown in the illustration.

HINT:
·

Install the No. 1 compression ring with the code mark (1N) facing upward.

·

Install the No. 2 compression ring with the code mark (2N) facing upward.



Text in Illustration
*1 No. 1 Compression Ring
*2 No. 2 Compression Ring
*a Code Mark


c.
A337675E02
1.26,1.031 0.958,0.875 0.958,0.875 0.563,0.875 false 0.073,0.115 0.479,0.313 0.406,0.198 10 false *1, *3 0.292,1.896 0.5,2.073 0.208,0.177 10 false *4 3.073,1.781 3.281,1.958 0.208,0.177 10 false *2 2.979,0.125 3.188,0.302 0.208,0.177 10 false *5 0.354,0.813 0.563,0.99 0.208,0.177 10 false *a

Position the piston rings so that the ring ends are as shown in the illustration.

Text in Illustration
*1 No. 1 Compression Ring
*2 No. 2 Compression Ring
*3 Oil Ring Expander
*4 Upper Oil Ring Side Rail
*5 Lower Oil Ring Side Rail
*a Front Mark

NOTICE:

Do not align the compression ring ends.



Hide 11711 10.INSTALL CRANKSHAFT BEARING

NOTICE:

Do not apply engine oil to the contact area or backside of the bearing.


HINT:

The crankshaft bearing cap bolts are tightened in 2 progressive steps.


a.

Clean the main journal and both surfaces of the bearing.


b.

Install the upper bearing.

i.
A101500E09
1.354,2.854 0.896,2.396 0.896,2.396 2.219,2.844 false 0.677,2.25 0.885,2.469 0.208,0.219 10 false *c 1.198,3.885 1.656,4.188 0.458,0.302 10 true *a 2.115,3.865 2.802,4.208 0.688,0.344 10 true *b

Install the upper bearing to the cylinder block as shown in the illustration.

Reference (Difference in Dimension of Cylinder Block and Bearing):
Item Specified Condition
# 1, 5 journal 3.75 mm (0.148 in.)
# 3 journal 1.75 mm (0.0689 in.)
# 2, 4 journal 2.75 mm (0.108 in.)


NOTICE:
·

Do not apply engine oil to the bearings or their contact surfaces.

·

Both sides of the oil groove in the cylinder block should be visible through the oil feed holes in the bearing. The amount visible on each side of the holes should be equal.



Text in Illustration
*a CORRECT
*b INCORRECT
*c Oil Groove



c.
A101501E04
2.74,0.458 3.042,0.688 0.302,0.229 10 false (A) 2.75,1.688 3.052,1.958 0.302,0.271 10 false (B)

Install the lower bearing.

i.

Install the lower bearing to the bearing cap.


ii.

Using a vernier caliper, measure the distance between the bearing cap edge and lower bearing edge.

Dimension A - B or B - A:

0.3 mm (0.0118 in.) or less


Reference (Dimension of A or B):
Item Specified Condition
# 1, 5 journal 3.75 mm (0.148 in.)
# 3 journal 1.75 mm (0.0689 in.)
# 2, 4 journal 2.75 mm (0.108 in.)


NOTICE:

Do not apply engine oil to the bearings or their contact surfaces.




d.

With the upper bearing and lower bearing installed, use a plastic-faced hammer to install the bearing caps to the cylinder block.

NOTICE:

Make sure that the bearing caps are installed in the correct positions and facing in the correct direction.



e.
A101502E06
2.379,0.373 2.580,0.558 0.201,0.185 10 *a

Using a vernier caliper, measure the amount of misalignment between the upper bearing and lower bearing as shown in the illustration.

Standard misalignment:

0.9 mm (0.0354 in.) or less


Text in Illustration
*a Misalignment


f.

Remove the bearing cap.


g.

Apply engine oil to the thrust washers.


h.
A101503E05
1.39,2.462 0.909,3.034 0.909,3.034 1.736,2.733 false 0.673,2.973 0.866,3.144 0.192,0.172 10 *a

Install the 2 thrust washers to the No. 3 journal position of the cylinder block with the oil grooves facing outward.

Text in Illustration
*a Oil Groove

NOTICE:

Be careful when installing the upper and lower thrust washers as they are similar but cannot be interchanged.



i.
A101504E07
0.802,1.052 0.74,0.781 0.74,0.781 0.667,0.781 false 2.458,0.365 2.729,0.365 false 0.708,1.188 0.708,1.719 false 1.115,1.51 0.708,1.51 false 0.646,1.75 0.844,1.948 0.198,0.198 10 false *b 0.469,0.688 0.667,0.875 0.198,0.188 10 false *a 2.76,0.25 2.958,0.438 0.198,0.188 10 false *a

Install the 2 thrust washers to the No. 3 bearing cap with the grooves facing outward.

Text in Illustration
*a Claw
*b Oil Groove

NOTICE:

Be careful when installing the thrust bearing upper and lower as they are similar but cannot be interchanged. The bearing lower has a claw as shown in the illustration.



j.

Apply engine oil to the lower bearing.


Hide 13411 11.INSTALL CRANKSHAFT

a.

Apply engine oil to the upper bearing, and then place the crankshaft on the cylinder block.


b.
A101506

Install the 5 crankshaft bearing caps in their proper locations.


c.

Install the crankshaft bearing cap bolt.

i.

Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts.


ii.

Temporarily install the crankshaft bearing cap bolts.

HINT:

The main bearing cap bolts are tightened in 2 progressive steps.



iii.
U147463E03
1.688,0.26 1.854,0.51 0.167,0.25 10 true 1 0.458,1.531 0.635,1.75 0.177,0.219 10 true 8 2.948,0.271 3.156,0.5 0.208,0.229 10 true 9 2.927,1.542 3.177,1.792 0.25,0.25 10 true 10 2.323,1.552 2.5,1.76 0.177,0.208 10 true 6 0.458,0.271 0.635,0.5 0.177,0.229 10 true 7 1.083,0.26 1.26,0.51 0.177,0.25 10 true 3 2.313,0.271 2.479,0.521 0.167,0.25 10 true 5 1.083,1.542 1.26,1.76 0.177,0.219 10 true 4 1.708,1.552 1.875,1.771 0.167,0.219 10 true 2

Step 1:

Uniformly tighten the 10 main bearing cap bolts in the sequence shown in the illustration.

Torque:
39 N*m (398 kgf*cm, 29 ft.*lbf)

If any of the main bearing cap bolts does not meet the torque specification, replace the main bearing cap bolt.


iv.

Mark the front of the bearing cap bolts with paint.


v.

Step 2:

Tighten the bearing cap bolts 90° in the sequence shown in step 1.


vi.

Check that the paint marks are now at a 90° angle to the front.



d.

Check that the crankshaft turns smoothly.


e.

Check the crankshaft thrust clearance (See page Engine / Hybrid System>2TR-FE (ENGINE MECHANICAL)>CYLINDER BLOCK>DISASSEMBLY).


Hide 13041 12.INSTALL CONNECTING ROD BEARING

a.
A101528E06
2.69,0.841 2.546,0.571 2.546,0.571 2.471,0.571 false 2.253,0.475 2.437,0.649 0.184,0.173 10 *a

Align the bearing claw with the groove of the connecting rod or connecting rod cap.

Text in Illustration
*a Claw


b.

Install the bearings to the connecting rod and connecting rod cap.

NOTICE:

Clean the backside of the bearing and the surface of the connecting rod or connecting rod cap that contacts the bearing.



Hide 13.INSTALL PISTON SUB-ASSEMBLY WITH CONNECTING ROD

a.

Apply engine oil to the cylinder walls, the pistons, and the surfaces of the connecting rod bearings.


b.
A337675E04
1.26,1.031 0.563,0.875 true 0.021,0.125 0.458,0.323 0.438,0.198 10 false *1, *3 0.302,1.885 0.51,2.063 0.208,0.177 10 false *4 3.063,1.792 3.271,1.969 0.208,0.177 10 false *2 2.958,0.135 3.167,0.313 0.208,0.177 10 false *5 0.354,0.75 0.563,0.927 0.208,0.177 10 false *a

Position the piston rings so that the ring ends are as shown in the illustration.

Text in Illustration
*1 No. 1 Compression Ring
*2 No. 2 Compression Ring
*3 Oil Ring Expander
*4 Upper Oil Ring Side Rail
*5 Lower Oil Ring Side Rail
*a Front Mark

NOTICE:

Do not align the compression ring ends.



c.
A101529E07
0.667,0.729 0.854,0.271 0.854,0.271 1.063,0.271 false 0.24,1.573 0.427,1.75 0.188,0.177 10 false *a 1.115,0.188 1.302,0.365 0.188,0.177 10 false *b

Using a piston ring compressor, push the numbered piston and connecting rod assembly into the correct cylinder with the front mark of the piston facing forward.

Text in Illustration
*a Front
*b Front Mark


d.

Match the numbered connecting rod cap with the correct connecting rod.


e.
A101476E07
1.333,0.708 0.854,0.156 0.854,0.156 0.729,0.156 false 0.51,0.063 0.698,0.24 0.188,0.177 10 false *a

Check that the front mark of the connecting rod cap is facing forward.

Text in Illustration
*a Front Mark


f.

Install the connecting rod cap bolts.

HINT:

The connecting rod cap bolts are tightened in 2 progressive steps.


i.

Apply a light coat of engine oil to the threads and under the heads of the connecting rod cap bolts.


ii.
A101477

Step 1:

Install and alternately tighten the bolts of the connecting rod cap in several steps.

Torque:
25 N*m (250 kgf*cm, 18 ft.*lbf)


iii.

Mark the front of each connecting rod cap bolt with paint.


iv.

Step 2:

Tighten the cap bolts 90° as shown.


v.

Check that the painted marks are now at a 90° angle to the front.



g.

Check that the crankshaft turns smoothly.


h.

Check the connecting rod thrust clearance (See page Engine / Hybrid System>2TR-FE (ENGINE MECHANICAL)>CYLINDER BLOCK>DISASSEMBLY).