Home › Engine / Hybrid System › 1KD-FTV (ENGINE MECHANICAL) › CYLINDER BLOCK › 2015.06–2020.08
RM27T0E _51 Engine / Hybrid System _053664 1KD-FTV ENGINE MECHANICAL _0260518 CYLINDER BLOCK A

1KD-FTV ENGINE MECHANICAL  CYLINDER BLOCK  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL STUD BOLT

HINT:

If a stud bolt is deformed or the threads are damaged, replace it.


a.

Install the stud bolts.

A225491E02
0.729,0.146 0.938,0.313 0.208,0.167 10 false *A 3.927,0.146 4.104,0.313 0.177,0.167 10 false *B 0.729,2.156 0.938,2.354 0.208,0.198 10 false *C 3.927,2.156 4.146,2.354 0.219,0.198 10 false *D 5.052,8.458 5.208,8.625 0.156,0.167 10 false D 1.469,4.354 1.635,4.521 0.167,0.167 10 false C 1.271,8.458 1.417,8.625 0.146,0.167 10 false C 1.302,6.958 1.427,7.125 0.125,0.167 10 false A 5.479,2.448 5.625,2.615 0.146,0.167 10 false D 5.656,2.448 5.781,2.615 0.125,0.167 10 false D 4.469,0.271 4.594,0.448 0.125,0.177 10 false B 5.073,6.958 5.198,7.146 0.125,0.188 10 false B 5.563,0.146 5.688,0.313 0.125,0.167 10 false B 2.625,0.823 2.76,0.99 0.135,0.167 10 false B 0.969,1.698 1.115,1.854 0.146,0.156 10 true A 2.24,5.635 2.865,5.969 0.625,0.333 10 false 69 mm (2.72 in.) 5.875,6.219 6.448,6.552 0.573,0.333 10 false 29 mm (1.14 in.) 2.229,7.792 2.854,8.125 0.625,0.333 10 false 26 mm (1.02 in.) 4.688,7.604 5.406,7.938 0.719,0.333 10 false 9 mm (0.354 in.) 4.688,8.104 5.406,8.438 0.719,0.333 10 false 9 mm (0.354 in.) 1.063,7.542 1.75,7.875 0.688,0.333 10 false 12 mm (0.472 in.) 1.063,8.083 1.75,8.417 0.688,0.333 10 false 12 mm (0.472 in.) 5.875,7.833 6.573,8.167 0.698,0.333 10 false 23 mm (0.906 in.) 4.688,6.552 5.375,6.885 0.688,0.333 10 false 9.5 mm (0.374 in.) 4.688,5.896 5.396,6.229 0.708,0.333 10 false 9.5 mm (0.374 in.) 1.052,4.76 1.75,5.146 0.698,0.385 10 false 9 mm (0.354 in.) 1.052,6.563 1.698,6.917 0.646,0.354 10 false 9 mm (0.354 in.) 1.271,7.135 1.563,7.333 0.292,0.198 10 false M6 5.031,7.125 5.323,7.323 0.292,0.198 10 false M6 1.24,8.615 1.531,8.813 0.292,0.198 10 false M8 5.021,8.615 5.323,8.813 0.302,0.198 10 false M6 1.938,1.573 2.083,1.729 0.146,0.156 10 true A 1.531,1.552 1.677,1.708 0.146,0.156 10 true A

Text in Illustration
*A for Front Side *B for Left Side
*C for Oil Pan Side *D for Right Side


Hide 15708 2.INSTALL NO. 1 OIL NOZZLE SUB-ASSEMBLY

a.
A060268

Align the pin of the No. 1 oil nozzle with the pin hole of the cylinder block.


b.

Install the 4 No. 1 oil nozzles with the 4 check valves.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


Hide 13101 3.INSTALL PISTON WITH PIN SUB-ASSEMBLY

a.
A060203

Using a small screwdriver, install a new snap ring on one side of the piston pin hole.


b.
A060230

Gradually heat the piston to approximately 80°C (176°F).


c.

Coat the piston pin with engine oil.


d.
A226793E01
0.919,0.588 1.076,0.833 1.076,0.833 1.076,0.866 false 0.978,0.885 1.152,1.055 0.174,0.169 10 *1 0.256,2.267 0.430,2.436 0.174,0.169 10 *2 0.874,2.356 0.452,2.356 false

Align the front marks of the piston and connecting rod, connect the connecting rod to the piston, and then push in the piston pin with your thumb.

Text in Illustration
*1 Front Mark (Arrow)
*2 Front Mark (Protrusion)


e.

Check the fit between the piston and piston pin. Try to move the piston back and forth on the piston pin.


f.
A149754

Using a small screwdriver, install a new snap ring on the other side of the piston pin hole.


Hide 13011 4.INSTALL PISTON RING SET

a.
A226794E01
1.596,1.917 1.765,2.073 0.170,0.156 10 *2 1.596,0.436 1.765,0.592 0.170,0.156 10 *1 1.686,0.101 1.686,0.428 false

Install the coil and oil ring by hand.

Text in Illustration
*1 Coil Joint
*2 Oil Ring End

HINT:

Make sure the end gap of the oil ring and the coil joint are on opposite sides.



b.
A226155E01
0.698,0.698 0.375,0.302 0.375,0.302 0.292,0.302 false 0.698,1.417 0.375,1.052 0.375,1.052 0.292,1.052 false 0.104,0.198 0.302,0.365 0.198,0.167 10 false *1 0.115,0.969 0.313,1.135 0.198,0.167 10 false *2

Using a piston ring expander, install the No. 1 and No. 2 piston rings with the code marks facing upward.

Code Mark:
Ring Code Mark
No. 1 NAA or NAC
No. 2 N or KD1


Text in Illustration
*1 No. 1
*2 No. 2


c.
A226156E01
0.758,0.362 0.946,0.545 0.187,0.183 10 *1 2.438,0.362 2.625,0.545 0.187,0.183 10 *2 2.438,1.568 2.625,1.750 0.187,0.183 10 *4 0.758,1.568 0.946,1.750 0.187,0.183 10 *3 1.978,0.085 2.165,0.268 0.187,0.183 10 *5 1.698,0.612 1.887,0.168 1.887,0.168 1.944,0.168 false

Position the piston rings so that the ring ends are as shown in the illustration.

Text in Illustration
*1 No. 1 Piston Ring
*2 Oil Ring
*3 Coil
*4 No. 2 Piston Ring
*5 Front Mark (Arrow)

NOTICE:

Do not align the ring ends.



Hide 11711 5.INSTALL CRANKSHAFT BEARING

A060228

HINT:

Upper bearings have an oil groove and oil hole. Lower bearings do not.


a.

Align the bearing claw with the claw groove of the cylinder block and push in the 5 upper bearings.


b.
A060190

Align the bearing claw with the claw groove of the crankshaft bearing cap and push in the 5 lower bearings.


Hide 13411 6.INSTALL CRANKSHAFT

A060188

a.

Place the crankshaft on the cylinder block.


b.

Push the crankshaft in one direction and install one thrust washer to the No. 5 journal position with the oil groove facing outward.


c.

Push the crankshaft in the opposite direction and install the other thrust washer to the No. 5 journal position with the oil groove facing outward.


d.
A060189

Install the 2 thrust washers to the No. 5 bearing cap with the grooves facing outward.


e.
A060226

Install the 5 crankshaft bearing caps to their proper locations.


f.
A060270E11
0.146,0.677 0.333,0.875 0.188,0.198 10 false 10 0.833,0.448 0.99,0.615 0.156,0.167 10 false 4 1.417,0.208 1.552,0.385 0.135,0.177 10 false 1 1.979,0.01 2.146,0.188 0.167,0.177 10 false 6 2.958,0.021 3.094,0.198 0.135,0.177 10 false 7 3.125,1.073 3.25,1.26 0.125,0.188 10 true 8 2.604,1.281 2.729,1.479 0.125,0.198 10 true 3 2.063,1.5 2.188,1.667 0.125,0.167 10 true 2 1.51,1.771 1.656,1.969 0.146,0.198 10 true 5 0.865,1.979 1,2.146 0.135,0.167 10 false 9

Install the crankshaft bearing cap bolts.

HINT:
·

The crankshaft bearing cap bolts are tightened in 2 progressive steps.

·

If a crankshaft bearing cap bolt is broken or deformed, replace it.



i.

Apply a light coat of engine oil to the threads and under the bolt heads of the crankshaft bearing cap bolts.


ii.

Install and uniformly tighten the 10 bolts of the crankshaft bearing caps in several passes in the sequence shown in the illustration.

Torque:
50 N*m (510 kgf*cm, 37 ft.*lbf)

If any one of the bearing cap bolts does not meet the torque specification, replace the bearing cap bolt.


iii.
A060271E08
0.646,0.302 0.792,0.854 0.792,0.854 0.792,0.938 false 0.073,0.177 0.333,0.344 0.26,0.167 10 false 90° 1.167,0.135 1.417,0.313 0.25,0.177 10 false 90° 0.271,0.563 0.448,0.74 0.177,0.177 10 false *a 0.698,0.938 0.875,1.115 0.177,0.177 10 true *1

Mark the front of each crankshaft bearing cap bolt with paint.

Text in Illustration
*1 Painted Mark
*a Front


iv.

Tighten the crankshaft bearing cap bolts by 90° in the numerical order shown in the previous illustration.


v.

Check that the painted marks are now at a 90° angle to the front.



g.

Check that the crankshaft turns smoothly.


h.

Check the crankshaft thrust clearance.


Hide 13041 7.INSTALL CONNECTING ROD BEARING

a.
A060205

Align the bearing claw with the groove of the connecting rod or connecting rod cap.


b.

Install the bearings to the connecting rod and connecting rod cap.


Hide 9.INSTALL PISTON AND CONNECTING ROD

a.

Apply engine oil to the cylinder walls, pistons and the surfaces of the connecting rod bearings.


b.

Check the positions of the piston ring ends.


c.
A226796E01
0.313,0.969 0.5,1.146 0.188,0.177 10 false *1

Using a piston ring compressor, push the correctly numbered piston and connecting rod assembly into the cylinder with the front mark of the piston facing forward.

Text in Illustration
*1 Front Mark (Arrow)


d.
A060237

Place the connecting rod cap on the connecting rod.

i.

Match each numbered connecting rod cap with the correct connecting rod.


ii.

Align the pins of the connecting rod cap with the pin holes of the connecting rod and install the connecting rod cap.


iii.
A060238E02
1.396,0.844 0.667,1.292 0.667,1.292 0.667,1.396 false 0.563,1.417 0.75,1.583 0.188,0.167 10 false *1

Check that the front mark of the connecting rod cap is facing forward.

Text in Illustration
*1 Front Mark (Protrusion)
V100135

Front



e.
A060235

Install the connecting rod cap bolts.

HINT:
·

The connecting rod cap bolts are tightened in 2 progressive steps.

·

If any connecting rod bolt is broken or deformed, replace it.



i.

Apply a light coat of engine oil to the threads and under the heads of the connecting rod cap bolts.


ii.

Install and alternately tighten the bolts of the connecting rod cap in several passes.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)

HINT:

If any one of the connecting rod cap bolts does not meet the torque specification, replace the cap bolt.



iii.
A060197E05
0.51,0.333 0.625,0.99 0.625,0.99 0.625,1.052 false 0.021,0.125 0.354,0.313 0.333,0.188 10 false 90° 1,0.146 1.333,0.333 0.333,0.188 10 false 90° 0.198,0.594 0.365,0.792 0.167,0.198 10 false *a 0.531,1.063 0.719,1.208 0.188,0.146 10 false *1

Mark the front of each connecting rod cap bolt with paint.

Text in Illustration
*1 Painted Mark
*a Front


iv.

Tighten the connecting rod cap bolts by 90° as shown in the illustration.


v.

Check that the painted marks are now at a 90° angle to the front.



f.

Check that the crankshaft turns smoothly.


Hide 11448 11.INSTALL CYLINDER BLOCK OIL ORIFICE