Home › Engine / Hybrid System › 1GD-FTV (ENGINE MECHANICAL) › CYLINDER BLOCK
RM27T0E _51 Engine / Hybrid System _053665 1GD-FTV ENGINE MECHANICAL _0260521 CYLINDER BLOCK A

1GD-FTV ENGINE MECHANICAL  CYLINDER BLOCK  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.


a.

Using an E6 "TORX" socket wrench, install the stud bolt labeled A to the cylinder block sub-assembly.

Torque:
for stud bolt A : 6.0 N*m (61 kgf*cm, 53 in.*lbf)


b.

Using an E8 "TORX" socket wrench, install the stud bolts labeled B, D and E to the cylinder block sub-assembly.

Torque:
for stud bolt B, D and E : 10 N*m (102 kgf*cm, 7 ft.*lbf)


c.

Using an E10 "TORX" socket wrench, install the stud bolt labeled C to the cylinder block sub-assembly.

Torque:
for stud bolt C : 19 N*m (194 kgf*cm, 14 ft.*lbf)

A337484E03
2.26,0.198 2.448,0.354 0.188,0.156 10 false *a 0.698,2.073 0.885,2.229 0.188,0.156 10 false *b 3.896,2.115 4.083,2.271 0.188,0.156 10 false *c 1.188,4.854 1.375,5.01 0.188,0.156 10 false *d 1.583,5 1.771,5.156 0.188,0.156 10 false *e 3.99,5.177 4.177,5.333 0.188,0.156 10 false *g 1.177,6.667 1.385,6.823 0.208,0.156 10 false *h 1.177,7.313 1.365,7.469 0.188,0.156 10 false *i 1.594,6.917 1.781,7.104 0.188,0.188 10 false *j 3.573,6.833 3.76,6.99 0.188,0.156 10 false *k 3.583,7.375 3.771,7.531 0.188,0.156 10 false *l 3.979,7.01 4.229,7.167 0.25,0.156 10 false *m 5.969,6.542 6.156,6.698 0.188,0.156 10 false *n 6.396,5.531 6.583,5.688 0.188,0.156 10 false *o 1.177,5.167 1.365,5.323 0.188,0.156 10 false *d 3.583,4.76 3.771,4.917 0.188,0.156 10 false *e 3.573,5.583 3.76,5.74 0.188,0.156 10 false *f 5.969,4.771 6.156,4.927 0.188,0.156 10 false *k 0.729,4.469 0.875,4.625 0.146,0.156 10 false A 3.167,4.146 3.313,4.302 0.146,0.156 10 false B 0.719,5.979 0.865,6.135 0.146,0.156 10 false C 3.167,6.198 3.313,6.354 0.146,0.156 10 false D 5.563,4.156 5.708,4.313 0.146,0.156 10 false E 4.083,0.188 4.229,0.344 0.146,0.156 10 false A 2.198,2.146 2.344,2.302 0.146,0.156 10 false B 3.656,2.552 3.802,2.708 0.146,0.156 10 false C 5.75,2.24 5.896,2.396 0.146,0.156 10 true D 5.469,3.896 5.615,4.052 0.146,0.156 10 false E 2.323,3.052 2.5,3.24 0.177,0.188 10 true B 5.969,2.292 6.115,2.448 0.146,0.156 10 true D 6.323,3.156 6.469,3.313 0.146,0.156 10 false D 5.969,3.875 6.115,4.031 0.146,0.156 10 false D 5.292,3.469 5.448,3.646 0.156,0.177 10 true D 4.896,3.729 5.052,3.917 0.156,0.188 10 true D 4.521,3.542 4.677,3.74 0.156,0.198 10 true D

Text in Illustration
*a Engine Lower Side *b Engine LH Side
*c Engine RH Side *d 9.0 mm (0.354 in.)
*e 19 mm (0.748 in.) *f 16 mm (0.630 in.)
*g 44 mm (1.73 in.) *h 23 mm (0.906 in.)
*i 15 mm (0.591 in.) *j 40 mm (1.57 in.)
*k 20 mm (0.787 in.) *l 10 mm (0.394 in.)
*m 32 mm (1.26 in.) *n 13 mm (0.511 in.)
*o 73 mm (2.87 in.) - -


Hide 11415 2.INSTALL CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY

a.
A343485E01
2.208,1.854 2.552,2.052 0.344,0.198 10 false 30°

Install a new cylinder block water drain cock sub-assembly to the cylinder block sub-assembly.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)

HINT:

Install the cylinder block water drain cock sub-assembly so that the installation angle is within the range indicated by the illustration.



b.

Install a new cylinder block water drain cock plug to the cylinder block water drain cock sub-assembly.

Torque:
13 N*m (130 kgf*cm, 9 ft.*lbf)


Hide 15708 3.INSTALL NO. 1 OIL NOZZLE SUB-ASSEMBLY

a.

Using a 5 mm hexagon wrench, install the 4 No. 1 oil nozzle sub-assemblies to the cylinder block sub-assembly with the 4 bolts.

Torque:
10 N*m (102 kgf*cm, 9 ft.*lbf)


Hide 13101 4.INSTALL PISTON WITH PIN SUB-ASSEMBLY

a.
A343439E01
1.029,0.174 1.214,0.329 0.185,0.155 10 *1 3.193,0.45 3.378,0.605 0.185,0.155 10 *a 1.235,0.269 1.906,0.269 false 2.541,0.555 3.17,0.555 false

Using a small screwdriver, install a new piston pin hole snap ring on one side of the piston pin hole.

Text in Illustration
*1 Piston Pin Hole Snap Ring
*a Service Hole Cutout Portion

HINT:
·

Be sure that the end gap of the piston pin hole snap ring is not aligned with the service hole cutout portion of the piston.

·

If the new piston pin is difficult to insert, heat the piston to approximately 80°C (176°F).

CAUTION:

Be sure to wear protective gloves.





b.

Coat the piston pin with engine oil.


c.
A343441E01
1.495,1.144 1.680,1.299 0.185,0.155 10 *a 0.306,2.032 0.491,2.187 0.185,0.155 10 *b 0.979,1.245 1.467,1.245 false 0.517,2.143 0.67,2.143 0.67,2.143 0.911,2.529 false

Align the front marks of the piston and connecting rod sub-assembly, install the connecting rod sub-assembly to the piston and push in the piston pin with your thumb.

Text in Illustration
*a Front Mark (Arrow)
*b Front Mark (Protrusion)


d.

Check the fitting condition between the piston and piston pin by trying to move the piston back and forth on the piston pin.


e.
A343443E01
3.171,1.042 3.356,1.197 0.185,0.155 10 *1 2.237,1.016 2.422,1.171 0.185,0.155 10 *a 2.453,1.134 2.623,1.134 2.623,1.134 2.623,1.878 false 3.139,1.134 2.969,1.134 2.969,1.134 2.969,1.411 false

Using a small screwdriver, install a new piston pin hole snap ring on one side of the piston pin hole.

Text in Illustration
*1 Piston Pin Hole Snap Ring
*a Service Hole Cutout Portion

HINT:

Be sure that the end gap of the piston pin hole snap ring is not aligned with the service hole cutout portion of the piston.



Hide 13011 5.INSTALL PISTON RING SET

a.

Install the oil ring expander to the piston by hand.


b.
A343447E01
1.26,4.531 1.438,4.531 1.438,4.531 1.615,4.344 false 2.198,4.531 2.031,4.531 2.031,4.531 1.844,4.344 false 1.729,2.625 1.729,3.146 false 1.615,3.146 1.802,3.302 0.188,0.156 10 false *a 1.073,4.438 1.26,4.594 0.188,0.156 10 false *b 2.24,4.438 2.427,4.594 0.188,0.156 10 false *b

Using a piston ring expander, install the oil ring rail to the piston.

Text in Illustration
*a Coil Joint
*b Oil Ring Rail End Gap

HINT:

Make sure the end gap of the oil ring rail and the coil joint are on opposite sides.



c.
A343448E01
0.573,0.219 0.75,0.219 0.75,0.219 0.833,0.677 false 0.865,1.417 0.865,1.927 false 0.365,0.104 0.552,0.26 0.188,0.156 10 false *a 0.781,1.948 0.969,2.104 0.188,0.156 10 false *b

Using a piston ring expander, install the No. 1 compression ring and No. 2 compression ring to the piston so that the code marks are positioned as shown in the illustration.

Code Mark:
Item Code Mark
No. 1 Compression Ring G1
No. 2 Compression Ring N2


Text in Illustration
*a No. 1 Compression Ring Code Mark
*b No. 2 Compression Ring Code Mark

HINT:

Install the No. 1 compression ring and No. 2 compression ring with the code mark facing upward.



d.
A343449E01
2.419,1.556 2.621,1.711 0.202,0.155 10 *1 0.831,0.41 1.016,0.564 0.185,0.155 10 *2 2.446,0.45 2.631,0.605 0.185,0.155 10 *3 0.816,1.537 1.012,1.692 0.196,0.155 10 *4 0.13,0.879 0.315,1.034 0.185,0.155 10 *a 0.334,0.989 0.884,0.989 false

Position the piston rings so that the ring ends are as shown in the illustration.

Text in Illustration
*1 No. 1 Compression Ring
*2 No. 2 Compression Ring
*3 Oil Ring Expander
*4 Oil Ring Rail
*a Front Mark (Arrow)

NOTICE:

Do not align the ring ends.



Hide 6.INSTALL CRANKSHAFT BEARING

HINT:

No. 1 crankshaft bearings have an oil groove and oil hole. No. 2 crankshaft bearings do not.


a.
A343452E01
2.457,2.883 2.641,3.037 0.185,0.155 10 *a

Install the No. 1 crankshaft bearing to the cylinder block sub-assembly as shown in the illustration.

Standard width:

4.25 mm (0.167 in.)


Text in Illustration
*a Width

NOTICE:
·

Clean the contact surface of the No. 1 crankshaft bearing and cylinder block sub-assembly.

·

Apply oil to the inner surface of each No. 1 crankshaft bearing (the surface which contacts the crankshaft), but not to the outer surface (the surface which contacts the cylinder block sub-assembly).




b.
A343582E01
0.896,2.833 1.063,3.01 0.167,0.177 10 false A 2.563,2.844 2.729,3.021 0.167,0.177 10 false B

Install the No. 2 crankshaft bearing to the crankshaft bearing cap.

NOTICE:
·

Clean the contact surface of the No. 2 crankshaft bearing and crankshaft bearing cap.

·

Apply oil to the inner surface of each No. 2 crankshaft bearing (the surface which contacts the crankshaft), but not to the outer surface (the surface which contacts the crankshaft bearing cap).




c.

Using a vernier caliper, measure the distance between the crankshaft bearing cap edge and crankshaft bearing edge.

Dimension A - B or B - A:

0 to 0.7 mm (0 to 0.0276 in.)



Hide 13411 7.INSTALL CRANKSHAFT

a.

Apply engine oil to the crankshaft bearing, and then install the crankshaft to the cylinder block sub-assembly.


b.
A343453E01
0.469,1.344 0.654,1.498 0.185,0.155 10 *1 2.081,1.34 2.266,1.495 0.185,0.155 10 *2 0.673,1.441 1.33,1.441 false 2.295,1.441 2.952,1.441 false

Apply engine oil to the 2 upper crankshaft thrust washers and 2 lower crankshaft thrust washers.

Text in Illustration
*1 Lower Crankshaft Thrust Washer
*2 Upper Crankshaft Thrust Washer

HINT:

Check the crankshaft thrust washers, as there are different types as shown in the illustration.



c.
A343454E01
2.125,1.729 2.875,1.729 2.875,1.729 2.875,1.042 true 2.063,1.042 3.135,1.042 true 0.5,1.99 1.573,1.99 true 1.146,1.542 0.646,1.542 0.646,1.542 0.646,1.99 true 3.167,0.938 3.354,1.094 0.188,0.156 10 false *a 0.302,1.896 0.5,2.073 0.198,0.177 10 true *a

Push the crankshaft in one direction and install one upper crankshaft thrust washer to the No. 5 cylinder block sub-assembly journal position with the oil groove facing outward.

Text in Illustration
*a Groove


d.

Push the crankshaft in the opposite direction and install the other upper crankshaft thrust washer to the No. 5 cylinder block sub-assembly journal position with the oil groove facing outward.


e.
A343455E01
0.209,0.863 0.394,1.018 0.185,0.155 10 *a 0.422,0.973 1.159,0.973 false 1.01,1.848 1.195,2.003 0.185,0.155 10 *a 1.226,1.957 1.412,1.957 1.412,1.957 1.687,1.447 false 1.99,0.2 1.803,0.2 1.803,0.2 1.528,0.709 false 2.523,0.607 2.337,0.607 2.337,0.607 2.062,1.117 false 2.015,0.1 2.199,0.255 0.185,0.155 10 *a 2.552,0.503 2.737,0.658 0.185,0.155 10 *a

Install the 2 lower crankshaft thrust washers to the crankshaft bearing cap (No. 5 crankshaft journal) with the grooves facing outward.

Text in Illustration
*a Groove


f.
A343456E01
0.881,3.112 1.065,3.266 0.185,0.155 10 *a 0.998,2.688 0.998,3.118 false

Install the 5 crankshaft bearing caps to the cylinder block sub-assembly, making sure that the front marks (protrusions) and crankshaft bearing cap number of the crankshaft bearing caps are as shown in the illustration.

Text in Illustration
*a Front Mark (Protrusion)


g.

Apply a light coat of engine oil to the threads and under the heads of the crankshaft bearing cap set bolts.


h.

Install the crankshaft bearing cap set bolts.

HINT:
·

The crankshaft bearing cap set bolts are tightened in 2 progressive steps.

·

If a crankshaft bearing cap set bolt is broken or deformed, replace it.




i.
A337476E02
0.917,1.938 1.188,2.125 0.271,0.188 10 true 10 2.198,1.552 2.406,1.74 0.208,0.188 10 true 2 0.958,0.323 1.094,0.479 0.135,0.156 10 false 5 1.583,1.802 1.792,1.99 0.208,0.188 10 true 6 2.063,0.042 2.198,0.198 0.135,0.156 10 false 3 0.219,0.521 0.354,0.677 0.135,0.156 10 false 9 1.573,0.146 1.708,0.302 0.135,0.156 10 false 1 3.052,0.052 3.188,0.208 0.135,0.156 10 false 7 2.719,1.354 2.927,1.531 0.208,0.177 10 true 4 3.135,1.167 3.354,1.375 0.219,0.208 10 true 8

Step 1:

Using several steps, install and uniformly tighten the 10 crankshaft bearing cap set bolts in the sequence shown in the illustration.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)

HINT:

If any of the crankshaft bearing cap set bolts does not meet the torque specification, replace the crankshaft bearing cap set bolt.



j.

Step 2:

i.

Mark the front of the crankshaft bearing cap set bolts with paint.


ii.

Tighten the crankshaft bearing cap set bolts by 90°.


iii.

Check that the painted marks are now at a 90° angle to the front.



k.

Check that the crankshaft turns smoothly.


Hide 13041 9.INSTALL CONNECTING ROD BEARING

HINT:

Check that the No. 1 and No. 2 connecting rod bearing colors are correct, as the colors differ.

Bearing Color:
Item Connecting Rod Bearing Color
No. 1 Connecting Rod Bearing Brown
No. 2 Connecting Rod Bearing Silver


a.

Clean the backside of the connecting rod bearing and the connecting rod bearing surface of the connecting rod sub-assembly and connecting rod cap.


b.
A343450E01
1.458,0 1.643,0.155 0.185,0.155 10 *1 0.028,0.581 0.213,0.736 0.185,0.155 10 *2 1.189,2.302 1.339,2.457 0.150,0.155 10 A 2.117,2.302 2.267,2.457 0.150,0.155 10 B 0.237,0.674 0.903,0.674 false 1.662,0.087 1.813,0.087 1.813,0.087 1.979,0.477 false

Install the No. 1 connecting rod bearings to the connecting rod sub-assembly.

Text in Illustration
*1 No. 1 Connecting Rod Bearing
*2 No. 2 Connecting Rod Bearing


c.

Install the No. 2 connecting rod bearings to the connecting rod cap.


d.

Using a vernier caliper, measure the distance between the connecting rod cap edge and connecting rod bearing edge.

Dimension A - B or B - A:

0 to 0.7 mm (0 to 0.0276 in.)



Hide 10.INSTALL PISTON AND CONNECTING ROD SUB-ASSEMBLY

a.

Apply engine oil to the cylinder walls, pistons and surfaces of the connecting rod bearings.


b.
A343449E01
2.419,1.556 2.621,1.711 0.202,0.155 10 *1 0.831,0.41 1.016,0.564 0.185,0.155 10 *2 2.446,0.45 2.631,0.605 0.185,0.155 10 *3 0.816,1.537 1.012,1.692 0.196,0.155 10 *4 0.13,0.879 0.315,1.034 0.185,0.155 10 *a 0.334,0.989 0.884,0.989 false

Position the piston rings so that the piston ring ends are as shown in the illustration.

Text in Illustration
*1 No. 1 Compression Ring
*2 No. 2 Compression Ring
*3 Oil Ring Expander
*4 Oil Ring Rail
*a Front Mark (Arrow)

NOTICE:

Do not align the piston ring ends.



c.
A343457E01
0.276,1.522 0.461,1.677 0.185,0.155 10 *a 0.387,1.529 0.387,0.813 false

Using a piston ring compressor and hammer handle, press a piston with connecting rod sub-assembly into each cylinder with the front mark (arrow) of the piston facing forward.

Text in Illustration
*a Front Mark (Arrow)


d.

Place the connecting rod cap on the connecting rod sub-assembly.

i.
A343459E01
0.823,0.167 1.021,0.167 1.021,0.167 1.156,0.813 true 1.792,2.031 1.583,2.031 1.583,2.031 1.469,1.469 true 1.813,1.927 2.042,2.125 0.229,0.198 10 true *a 0.625,0.063 0.844,0.25 0.219,0.188 10 true *a

Align the pin holes of the connecting rod cap with the pins of the connecting rod sub-assembly, and then install the connecting rod cap.

Text in Illustration
*a Pin


ii.
A343461E01
1.625,1.542 1.625,0.823 true 1.552,1.552 1.771,1.74 0.219,0.188 10 true *a

Check that the front mark (protrusion) of the connecting rod cap is facing forward.

Text in Illustration
*a Front Mark (Protrusion)
V100135

Front


iii.
A343584E01
0.375,1.26 0.542,1.26 0.542,1.26 1.417,1.01 true 1.625,2.063 1.625,2.781 true 1.552,2.792 1.771,2.979 0.219,0.188 10 true *a 0.188,1.156 0.406,1.333 0.219,0.177 10 false *b

Check that the matchmarks of the connecting rod sub-assembly and connecting rod cap are aligned.

Text in Illustration
*a Front Mark (Protrusion)
*b Matchmark



e.

Apply a light coat of engine oil to the threads and under the heads of the connecting rod bolts.


f.

Install the connecting rod bolts.

HINT:

The connecting rod bolts are tightened in 2 progressive steps.


i.
A343463

Step 1:

Install and alternately tighten the connecting rod bolts of each connecting rod cap in several steps.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


ii.

Mark the front side of each connecting rod bolt with paint.


iii.

Step 2:

Tighten the connecting rod bolts 90°.


iv.

Check that the paint marks are now at a 90° angle to the front.



g.

Check that the crankshaft turns smoothly.


Hide 11.INSPECT CONNECTING ROD SUB-ASSEMBLY THRUST CLEARANCE