Home › Engine / Hybrid System › 2TR-FE (FUEL) › FUEL SYSTEM › 2015.06–2020.08
RM27T0E _51 Engine / Hybrid System _053666 2TR-FE FUEL _0260530 FUEL SYSTEM G

2TR-FE FUEL  FUEL SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.CHECK FUEL PUMP OPERATION AND FOR FUEL LEAK

a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.

NOTICE:

Do not start the engine.



c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.


e.

Check the fuel pump operation.

i.

Check for pressure in the fuel inlet tube from the fuel line. Check that the sound of fuel flowing in the fuel tank can be heard.

If there is no sound, check the integration relay, fuel pump, ECM and wiring connector.




Hide 23221 2.CHECK FUEL PRESSURE


b.

Discharge the fuel system pressure (See page Engine / Hybrid System>2TR-FE (FUEL)>FUEL SYSTEM>PRECAUTION).


c.

Disconnect the cable from the negative battery terminal.

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




d.

e.
A293714E04
1.51,1.198 1.427,1.198 1.427,1.198 1.365,1 false 0.521,2.115 0.656,2.115 0.656,2.115 0.781,2.417 false 2.427,2.479 2.333,2.479 2.333,2.479 2.125,2.281 false 3.083,3.375 3.01,3.375 3.01,3.375 2.875,3.458 false 2.396,3.271 2.396,3.146 2.396,3.146 2.521,3.063 false 1.063,0.594 0.448,0.594 false 0.698,1.083 0.698,0.594 false 1.323,0.396 1.729,0.396 false 2.698,0.979 2.698,0.854 2.698,0.854 2.865,0.771 false 0.323,2 0.531,2.208 0.208,0.208 10 false *a 0.24,0.5 0.469,0.688 0.229,0.188 10 false *b 1.521,1.104 1.74,1.292 0.219,0.188 10 false *c 2.625,1 2.844,1.208 0.219,0.208 10 false *d 2.438,2.385 2.667,2.573 0.229,0.188 10 false *f 3.094,3.271 3.323,3.5 0.229,0.229 10 false *g 2.313,3.271 2.521,3.5 0.208,0.229 10 false *b 1.75,0.292 1.958,0.49 0.208,0.198 10 false *e

Install SST (pressure gauge) as shown in the illustration.

SST
09268-45101  (09268-41250, 09268-41260, 09268-41280, 09268-41500, 09268-41700, 95336-08070)

Text in Illustration
*a SST (Hose)
*b SST (Hose Band)
*c SST (T-Joint)
*d SST (Pressure Gauge)
*e SST (Hose Joint)
*f Fuel Hose
*g SST (Fuel Tube Connector)


f.

Wipe off any gasoline.


g.

Reconnect the cable to the negative battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



h.

Operate the fuel pump.

i.

Connect the GTS to the DLC3.


ii.

Turn the ignition switch to ON.

NOTICE:

Do not start the engine.



iii.

Turn the GTS on.


iv.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed / ON.



i.

Measure the fuel pressure.

Standard fuel pressure:

300 to 389 kPa (3.1 to 4.0 kgf/cm2, 44 to 56 psi)


If the pressure is higher than the specification, replace the fuel pressure regulator assembly.

If the pressure is below the specification, check the fuel hoses and connectors, fuel pump, fuel filter assembly and fuel pressure regulator assembly.


j.

Start the engine.


k.

Measure the fuel pressure.

Standard fuel pressure:

300 to 389 kPa (3.1 to 4.0 kgf/cm2, 44 to 56 psi)


If the pressure is not as specified, check the fuel pump, fuel pressure regulator assembly and/or fuel injector assemblies.


l.

Stop the engine.


m.

Check that the fuel pressure remains as specified for 5 minutes after the engine has stops.

Standard fuel pressure:

147 kPa (1.5 kgf/cm2, 21 psi) or higher


If the pressure is not as specified, check the fuel pump, fuel pressure regulator assembly and/or fuel injector assemblies.


n.

Disconnect the cable from the negative (-) battery terminal and carefully remove SST and the fuel tube connector to prevent gasoline from spraying.