Home › Engine / Hybrid System › 1KD-FTV (EMISSION CONTROL) › EGR VALVE › 2015.06–2020.08
RM27T0E _51 Engine / Hybrid System _053673 1KD-FTV EMISSION CONTROL _0260611 EGR VALVE G

1KD-FTV EMISSION CONTROL  EGR VALVE  INSPECTION  


PROCEDURE

Hide 25800 1.INSPECT ELECTRIC EGR CONTROL VALVE ASSEMBLY

a.
A147237

Inspect the electric EGR control valve.

i.

When a vacuum of 27 kPa (200 mmHg, 7.88 in.Hg) is applied to the diaphragm chamber, check that the shaft rises and air flows out.


ii.

Maintaining the above conditions, check that there are no leaks and the shaft stays in position.


iii.

Check that the valve does not have heavy carbon deposits and is not stuck.

If the result is not as specified, replace the electric EGR control valve.



b.

Inspect the EGR valve position sensor.

i.
A085764E05
1.781,1.115 1.781,1.802 true 2.5,1.781 2.5,1.698 2.5,1.698 2.115,1.115 true 1.667,1.823 1.885,1.969 0.219,0.146 10 false E2 2.375,1.823 2.615,1.969 0.24,0.146 10 false VC 0.146,0.125 0.333,0.323 0.188,0.198 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (VC) - 2 (E2) 20°C (68°F) 4.0 to 6.0 kΩ


Text in Illustration
*a Component without harness connected
(Electric EGR Control Valve)

If the result is not as specified, replace the electric EGR control valve assembly.



c.

Create a vacuum in the diaphragm chamber.

i.
A147238E03
0.406,1.188 0.26,1.552 0.26,1.552 0.26,1.625 true 0.646,1.188 0.844,1.583 0.844,1.583 0.844,1.646 true 0.74,1.667 0.948,1.823 0.208,0.156 10 false E2 0.052,1.667 0.458,1.823 0.406,0.156 10 false EGLS 0.156,0.125 0.354,0.281 0.198,0.156 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (EGLS) - 2 (E2) 20°C (68°F)
EGR valve is fully opened
2.0 to 7.0 kΩ
20°C (68°F)
EGR valve is fully closed
0.1 to 2.5 kΩ


Text in Illustration
*a Component without harness connected
(Electric EGR Control Valve)

HINT:

The resistance increases in proportion to the opening angle of the EGR valve.


If the result is not as specified, replace the electric EGR control valve assembly.



Hide 25630 2.INSPECT NO. 2 EGR VALVE ASSEMBLY (w/ EGR Cooler)

a.
A147245

When a vacuum of 33.3 kPa (250 mmHg, 9.83 in.Hg) is applied to the diaphragm chamber, check that the valve turns and air flows out.


b.

Maintaining the above conditions, check that there are no leaks and the valve does not return.


c.

Check that the valve does not have heavy carbon deposits and is not stuck.

If the result is not as specified, replace the No. 2 EGR valve.