Home › Engine / Hybrid System › 1GD-FTV (EMISSION CONTROL) › EMISSION CONTROL SYSTEM › 2015.06–2018.06
RM27T0E _51 Engine / Hybrid System _053675 1GD-FTV EMISSION CONTROL _0260619 EMISSION CONTROL SYSTEM G

1GD-FTV EMISSION CONTROL  EMISSION CONTROL SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.CHECK SEATING OF EGR VALVE

a.

Check that the engine starts and idles.


b.

Stop the engine.


Hide 25800 2.CHECK ELECTRIC EGR CONTROL VALVE ASSEMBLY OPERATION

a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position.


d.

Check the Data List.

Enter the following menus: Powertrain / Engine and ECT / Data List / Target EGR Valve Pos and Actual EGR Valve Pos

OK:
Control Range Condition Specified Condition
Active Test performed (Set EGR position to 0% → 30% → 60% → 90% → 60% → 30% → 0%) Actual EGR valve opening percentage changes according to Active Test operation


If the result is not as specified, refer to DTC P042E.


Hide 4.VISUALLY INSPECT HOSES, CONNECTIONS AND GASKETS

a.

Visually check that the hoses, connections and gaskets have no cracks, leaks or damage.

NOTICE:
·

Detachment or other problems with the engine oil dipstick, filler cap, PCV hose or other components may cause the engine to run improperly.

·

Air suction caused by disconnections, looseness or cracks in the parts of the air induction system between the diesel throttle body and cylinder head will cause engine failure or engine malfunctions.



If the result is not as specified, replace parts as necessary.


Hide 6. DPF FORCIBLE REGENERATION PROCEDURE

HINT:
·

If the value recorded by the ECM for the PM volume stored is not initialized when the MIL illuminates during excessive PM buildup (P2458 or P2463), PM forcible regeneration cannot be performed using the GTS.

The value recorded by the ECM for the PM volume stored cannot be initialized using the GTS.

·

PM volume stored initialization:

Remove the EFI-MAIN No. 1 fuse or disconnect the cable from the battery terminal for 60 seconds or more, and then reinstall the EFI-MAIN No. 1 fuse or reconnect the cable to the battery terminal.



a.

Connect the GTS to the DLC3.


b.

Start the engine and idle it until the engine coolant temperature reaches 70°C (158°F) or higher.


c.

for Manual Transmission:

Move the shift lever to N and set the parking brake.


d.

for Automatic Transmission:

Move the shift lever to P and set the parking brake.


e.

Maintain the maximum possible engine speed under no load for 10 seconds to blow out all soot from inside the exhaust pipe.

HINT:
·

If only a low engine speed is continuously maintained, soot may accumulate at the end of the catalyst.

·

When soot accumulates at the end of the catalyst, it may not be possible to perform PM forced regeneration control normally.




f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the DPF Rejuvenate (PM).

A266071E03
5.667,1.646 5.802,1.646 5.802,1.646 6.021,1.5 false 2.635,1.865 2.5,1.865 2.5,1.865 2.25,2.083 false 4.479,2.365 4.344,2.365 4.344,2.365 4.094,2.594 false 6.052,3 6.104,2.479 6.104,2.479 6.135,2.479 false 0.385,2 0.958,2.177 0.573,0.177 10 false 700 rpm 0.323,1.125 0.948,1.302 0.625,0.177 10 false 2000 rpm 0.323,1.365 0.948,1.542 0.625,0.177 10 false 1200 rpm 0.365,0.135 0.823,0.469 0.458,0.333 10 false Engine Speed 2.667,1.792 4.125,1.969 1.458,0.177 10 false PM Regeneration Start 3.844,1.542 5.708,1.719 1.865,0.177 10 false PM Regeneration Completion 3.438,3.177 4.708,3.344 1.271,0.167 10 false 15 minutes or more 6.552,3.354 6.896,3.531 0.344,0.177 10 false Time 4.51,2.292 5.688,2.469 1.177,0.177 10 false PM volume stored 6.167,2.375 7.125,2.729 0.958,0.354 10 false Approximately 0% 0.042,1.531 2.25,1.875 2.208,0.344 10 true (Ambient temperature: 25°C (77°F)) 0.417,2.177 0.906,2.375 0.49,0.198 10 false (Idling)

CAUTION:

Before performing the Active Test, make sure that there are no combustible materials around the DPF and tailpipe.


HINT:
·

When PM Accumulation Ratio is too low, Activate the DPF Rejuvenate (PM) cannot be performed. Therefore, rev the engine with no load at 3400 rpm for 5 to 10 minutes to increase PM Accumulation Ratio to 12% or more.

·

The engine speed differs depending on the ambient temperature.

·

The engine speed increases during the Active Test and the engine speed returns to idle when the Active Test is completed.

·

The time it takes to complete the Active Test varies depending on the PM volume stored. However, it usually takes approximately 15 to 40 minutes to complete the Active Test.

·

Do not cancel the Active Test unless absolutely necessary.

·

If the Active Test needs to be canceled, depress the accelerator pedal and race the engine or depress the clutch pedal to cancel the process.

·

If the differential pressure value increases too much during the Active Test, the fail-safe function activates and the Active Test is stopped.

·

Depending on various conditions, the Active Test may not be completed within 15 minutes. If 60 minutes elapse, the system stops the Active Test and illuminates the MIL. If this happens, an exhaust manifold converter (DPF) or exhaust fuel addition injector malfunction (low fuel addition volume) has occurred (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>DIAGNOSTIC TROUBLE CODE CHART).