Home › Engine / Hybrid System › 1GD-FTV (EMISSION CONTROL) › EGR BYPASS VALVE SWITCHING VALVE
RM27T0E _51 Engine / Hybrid System _053675 1GD-FTV EMISSION CONTROL _0260621 EGR BYPASS VALVE SWITCHING VALVE G

1GD-FTV EMISSION CONTROL  EGR BYPASS VALVE SWITCHING VALVE  INSPECTION  


PROCEDURE

Hide 25860 1.INSPECT NO. 1 VACUUM SWITCHING VALVE ASSEMBLY

a.
A346703E02
0.146,0.092 0.302,0.274 0.156,0.181 10 *a 0.671,0.389 0.827,0.570 0.156,0.181 10 1 1.156,0.704 1.006,0.48 1.006,0.48 0.787,0.48 false 1.26,0.755 1.685,0.755 false 1.698,0.664 1.854,0.845 0.156,0.181 10 2

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 33 to 39 Ω
1 - Body ground
2 - Body ground
20°C (68°F) 1 MΩ or higher


Text in Illustration
*a Component without harness connected
(No. 1 vacuum switching valve assembly)

If the result is not as specified, replace the No. 1 vacuum switching valve assembly.


b.

Check operation of the No. 1 vacuum switching valve assembly.

i.
A398468E01
2.635,2.635 2.885,2.969 2.885,2.969 2.99,2.969 true 0.885,2.281 1.052,2.281 1.052,2.281 1.552,2.781 true 0.885,3.073 1.052,3.073 1.052,3.073 1.385,2.906 true 2.573,1.688 2.885,1.885 0.313,0.198 10 false *b 0.708,2.219 0.958,2.365 0.25,0.146 10 false *c 0.677,3 0.927,3.146 0.25,0.146 10 false *d 3.021,2.906 3.271,3.052 0.25,0.146 10 false *e 1.646,0.563 1.896,0.708 0.25,0.146 10 false *a

When a vacuum of 60 kPa (450 mmHg, 18 in.Hg) is applied to port F, check that air flows from port E to the filter.

Text in Illustration
*a Vacuum
*b Air
*c Port E
*d Port F
*e Filter


ii.
A346705E01
1.333,1.447 1.333,1.821 1.333,1.821 1.161,1.821 false 1.135,1.46 0.916,1.46 false 1.9,0.802 2.179,0.802 false 1.767,0.755 1.569,0.527 1.569,0.527 1.397,0.527 false 0.379,0.616 0.535,0.797 0.156,0.181 10 *a 0.722,1.368 0.878,1.549 0.156,0.181 10 *b 0.963,1.725 1.118,1.906 0.156,0.181 10 *c 1.235,0.44 1.391,0.621 0.156,0.181 10 1 2.163,0.702 2.319,0.883 0.156,0.181 10 2

Apply battery voltage 12V across terminals 1 and 2.

Text in Illustration
*a Air
*b Port F
*c Port E


iii.

Check that air flows from port E to port F. If the result is not as specified, replace the No. 1 vacuum switching valve assembly.