Home › Engine / Hybrid System › 1KD-FTV (INTAKE / EXHAUST) › INTAKE MANIFOLD › 2015.06–2020.08
RM27T0E _51 Engine / Hybrid System _053679 1KD-FTV INTAKE / EXHAUST _0260648 INTAKE MANIFOLD G

1KD-FTV INTAKE / EXHAUST  INTAKE MANIFOLD  INSPECTION  


PROCEDURE

Hide 17111 1.INSPECT INTAKE MANIFOLD

NOTICE:
A152702

Do not adjust the adjusting screw or 2 swirl control valve actuator installation bolts.


A152703

a.

Disconnect the 2 vacuum hoses from the actuator.


b.

Check the operation of the swirl control valve.

i.

Check that the valve is fully opened under normal conditions.


ii.

Connect the vacuum pumps as shown in the illustration. First apply negative pressure to the diaphragm closer to the intake manifold. This cause the actuator rod to move, which causes the swirl control valve to move. Then, apply negative pressure to the diaphragm on the outer side. This cause the actuator rod to move further, which also causes the swirl control valve to move further. Check that the valve is fully closed when a negative pressure of 65 kPa (488 mmHg, 19.2 in.Hg) is applied.


iii.

Wait for 1 minute and check that the vacuum pump needle does not move. If the result is not as specified, replace the intake manifold.

HINT:

When applying negative pressure to the diaphragm on the outer side, the diaphragm closer to the intake manifold must be in a vacuum state.




Hide 2.INSPECT VACUUM SWITCHING VALVE (for Swirl Control Valve)

a.

Measure the resistance according to the value(s) in the table below.

A149922E03
0.426,1.388 0.544,1.532 0.118,0.144 10 1 0.424,1.686 0.546,1.829 0.122,0.143 10 2 1.191,1.757 0.543,1.757 false 1.134,1.69 0.632,1.46 0.632,1.46 0.543,1.46 false 1.507,2.63 1.626,2.774 0.118,0.144 10 1 1.818,2.635 1.940,2.778 0.122,0.143 10 2 1.555,2.024 1.555,2.605 false 1.623,2.07 1.861,2.561 1.861,2.561 1.861,2.605 false 4.235,1.395 4.353,1.538 0.118,0.144 10 1 4.233,1.692 4.355,1.835 0.122,0.143 10 2 5,1.764 4.352,1.764 false 4.943,1.696 4.441,1.466 4.441,1.466 4.352,1.466 false 5.317,2.634 5.435,2.778 0.118,0.144 10 1 5.628,2.639 5.750,2.782 0.122,0.143 10 2 5.365,2.029 5.365,2.61 false 5.433,2.074 5.671,2.565 5.671,2.565 5.671,2.61 false

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 33 to 39 Ω
1 - Body ground 20°C (68°F) 1 MΩ or higher
2 - Body ground


If the result is not as specified, replace the vacuum control valve set.


b.

Check the operation of the VSV.

i.
A152705E02
1.199,0.731 1.381,0.881 0.181,0.150 10 *1 1.403,0.815 1.484,0.815 1.484,0.815 1.834,1.237 false 3.048,1.68 3.229,1.830 0.181,0.150 10 *1 2.466,1.761 3.021,1.761 false 2.366,0.178 2.548,0.329 0.181,0.150 10 *a 2.882,0.63 3.063,0.780 0.181,0.150 10 *a 1.172,3.166 1.353,3.316 0.181,0.150 10 *2 0.226,1.387 0.407,1.538 0.181,0.150 10 *2 0.429,1.472 0.511,1.472 0.511,1.472 0.861,1.893 false 1.274,3.14 1.274,2.585 false

Check that air flows from port E to the filter.

Text in Illustration
*1 Port E
*2 Filter
*a Air

If the result is not as specified, replace the vacuum control valve set.



c.
A152706E02
1.496,0.009 1.680,0.155 0.184,0.145 10 *a 2.134,0.437 2.319,0.583 0.184,0.145 10 *a 2.232,0.111 2.416,0.256 0.184,0.145 10 *1 2.198,0.201 2.096,0.201 2.096,0.201 1.947,1.201 false 2.593,0.397 2.777,0.543 0.184,0.145 10 *2 2.559,0.487 2.457,0.487 2.457,0.487 2.13,1.137 false 3.197,1.976 3.381,2.121 0.184,0.145 10 *1 3.197,1.597 3.381,1.743 0.184,0.145 10 *2 2.675,1.688 3.171,1.688 false 2.5,1.834 3.082,2.068 3.082,2.068 3.171,2.068 false 0.48,1.422 0.594,1.568 0.115,0.145 10 1 0.48,1.717 0.594,1.862 0.115,0.145 10 2 1.276,1.508 0.615,1.508 false 1.345,1.597 0.705,1.8 0.705,1.8 0.615,1.8 false 1.448,2.916 1.563,3.062 0.115,0.145 10 1 1.805,2.916 1.920,3.062 0.115,0.145 10 2 1.854,1.988 1.854,2.891 false 1.793,1.918 1.503,2.83 1.503,2.83 1.503,2.891 false

Apply battery voltage across the terminals.

Text in Illustration
*1 Port E
*2 Port F
*a Air


d.

Check that air flows from port E to port F.

If the result is not as specified, replace the vacuum control valve set.