Home › Engine / Hybrid System › 1GD-FTV (INTAKE / EXHAUST) › INTAKE MANIFOLD › 2015.06–2020.08
RM27T0E _51 Engine / Hybrid System _053680 1GD-FTV INTAKE / EXHAUST _0260654 INTAKE MANIFOLD A

1GD-FTV INTAKE / EXHAUST  INTAKE MANIFOLD  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the parts in the following chart (A), replace the No. 1 injection pipe subassembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones

Replaced Parts (A) Pipes Requiring New Replacement
Injector assembly (including shuffling the injector assemblies between the cylinders)
·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly


Supply pump assembly Fuel inlet pipe sub-assembly
·

Common rail assembly

·

Cylinder block sub-assembly

·

Cylinder head sub-assembly

·

Cylinder head gasket

·

Timing chain case assembly


·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly

·

Fuel inlet pipe sub-assembly



·

After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly, clean them with a brush and compressed air.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 53737A 3.REMOVE FRONT NO. 1 FENDER APRON TO FRAME SEAL LH

Hide 25800 4.REMOVE EGR COOLER ASSEMBLY

Hide 11409 5.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

a.
A418177

w/ No. 2 Fuel Pipe Clamp:

Detach the No. 2 fuel pipe clamp from the engine oil level dipstick guide.


b.

Remove the engine oil level dipstick.


c.

Remove the bolt and engine oil level dipstick guide.


d.

Remove the O-ring and grommet from the engine oil level dipstick guide.


Hide 23812D 6.DISCONNECT NO. 2 FUEL PIPE

A352807

a.

Remove the bolt and disconnect the No. 2 fuel pipe.


Hide 7.REMOVE WIRING HARNESS CLAMP BRACKET

A352808

a.

Disconnect the diesel throttle body assembly connector and pre-stroke control valve connector.


b.
A353379

Detach the 2 wire harness clamps.


c.

Remove the bolt and wiring harness clamp bracket.


Hide 17118 8.REMOVE MANIFOLD STAY

A353380

a.

Remove the bolt and disconnect the wiring harness clamp bracket from the intake manifold stay.


b.
A454364

Remove the 2 bolts and manifold stay.


Hide 23804D 9.REMOVE NO. 4 FUEL PIPE SUB-ASSEMBLY

a.
A356214C07
0,0 0,0 false
V100136

Union Bolt
V100137

Bolt


Disconnect the No. 4 fuel pipe sub-assembly from the No. 1 fuel pipe.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>PRECAUTION


b.

Remove the bolt from the intake manifold.


c.

Remove the 2 union bolts and 2 gaskets from the supply pump assembly and fuel filter.


Hide 23815D 10.REMOVE NO. 3 FUEL PIPE

a.
A454519

Detach the clamp and disconnect the wire harness.


b.
A352782C03
0,0 0,0 false
V100135

Union Bolt
V100136

Supply Pump Hollow Screw


Remove the union bolts, supply pump hollow screw and 2 gaskets from the supply pump assembly and fuel filter.


c.

Remove the 2 fuel pipe clamps from the No. 3 fuel pipe and fuel filter.


Hide 23804C 11.REMOVE FUEL INLET PIPE SUB-ASSEMBLY

U169511C01
0.083,0 0.354,0.208 0.271,0.208 10 false *a 0.323,2.448 0.594,2.656 0.271,0.208 10 false *b
*a Common Rail Assembly Side
*b Fuel Supply Pump Assembly Side


a.

Remove the 2 bolts, No. 1 injection pipe clamp and No. 2 injection pipe clamp.


b.
U169505E01
0.541,1.054 0.983,1.242 0.441,0.188 10 SST 0.88,1.155 1.193,1.155 false 1.193,1.155 1.502,1.668 false

Using SST, loosen the fuel inlet pipe sub-assembly union nut of the common rail assembly side.

SST
09245-11010  

NOTICE:

If the No. 1 or No. 2 injection pipe clamp is removed from the inlet pipe sub-assembly, replace the No. 1 or No. 2 injection clamp with a new one.



c.

Using a 19 mm union nut wrench, loosen the inlet pipe sub-assembly union nut of the fuel supply pump assembly side.


Hide 23770 12.REMOVE NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY

A345101

a.

Slide the clamps and remove the No. 4 fuel hose from the No. 2 nozzle leakage pipe assembly and common rail assembly.


b.

Slide the 2 clamps and remove the No. 5 fuel hose from the No. 1 nozzle leakage pipe assembly and No. 2 nozzle leakage pipe assembly.


c.
A345102

Slide the clamp and disconnect the No. 6 fuel hose from the No. 3 nozzle leakage pipe assembly.


d.

Remove the 2 bolts and No. 2 nozzle leakage pipe assembly.


Hide 25804 13.REMOVE VACUUM CONTROL VALVE SET

A356215

a.

Disconnect the wire harness clamp and vacuum control valve set connector.


b.

Disconnect the 2 vacuum hoses from the swirl control valve actuator and vacuum transmitting pipe sub-assembly.


c.

Remove the bolt and vacuum control valve set from the intake manifold.


Hide 17111 14.REMOVE INTAKE MANIFOLD

A352783

a.

Remove the bolt and disconnect the wire harness bracket.


b.

Remove the 7 bolts, 2 nuts, intake manifold and gasket.