Home › Engine / Hybrid System › 5L-E (STARTING) › STARTER
RM27T0E _51 Engine / Hybrid System _053693 5L-E STARTING _0260723 STARTER G

5L-E STARTING  STARTER  INSPECTION  


PROCEDURE

Hide 28100 1.INSPECT STARTER ASSEMBLY

CAUTION:

As a large electric current passes through the cable during this inspection, a thick cable must be used. If not, the cable may became hot and cause injury.


NOTICE:

The following tests must each be performed within 3 to 5 seconds to prevent the coil from burning out.


a.

Mount the starter in a vise between aluminum plates.


b.

Perform a pull-in test.

i.

Remove the nut, and then disconnect the lead wire from terminal C.


ii.
A222272E01
0.321,0.05 0.490,0.199 0.170,0.149 10 *1 0.994,1.641 1.164,1.790 0.170,0.149 10 *2 1.161,0.805 0.624,0.133 0.624,0.133 0.51,0.133 false 1.338,1.612 1.251,1.729 1.251,1.729 1.183,1.729 false

Connect the battery to the magnet starter switch as shown in the illustration. Check that the clutch pinion gear extends.

Text in Illustration
*1 Terminal C
*2 Terminal 50

If the clutch pinion gear does not move, inspect the magnet starter switch assembly. If the magnet starter switch assembly is not as specified, replace it.



c.

Perform a holding test.

i.
A222273E01
1.409,0.061 1.588,0.215 0.179,0.154 10 *1 1.16,0.817 1.332,0.153 1.332,0.153 1.402,0.153 false

Disconnect the negative (-) terminal lead from terminal C with the condition specified in the pull-in test above being maintained. Check that the pinion gear remains extended.

Text in Illustration
*1 Terminal C

If the clutch pinion gear returns inward, inspect the magnet starter switch assembly. If the magnet starter switch assembly is not as specified, replace it.



d.

Inspect the clutch pinion gear return.

i.
A222274

Disconnect the negative (-) terminal lead from the starter body. Check that the clutch pinion gear returns inward.

If the clutch pinion gear does not return inward, inspect the magnet starter switch assembly. If the magnet starter switch assembly is not as specified, replace it.



e.

Perform an operation test without load.

i.

Connect the field coil lead wire to terminal C.

Torque:
5.9 N*m (60 kgf*cm, 52 in.*lbf)


ii.
U169197E01
0.399,1.405 0.566,1.558 0.167,0.154 10 *1 0.861,1.405 1.028,1.558 0.167,0.154 10 *2 1.191,1.928 1.133,1.492 1.133,1.492 1.054,1.492 false 0.779,1.851 0.651,1.491 0.651,1.491 0.591,1.491 false

Connect the battery and an ammeter to the starter as shown in the illustration.

Text in Illustration
*1 Terminal 30
*2 Terminal 50


iii.

Check that the starter rotates smoothly and steadily while the pinion gear is extended. Then measure the current.

Specified current:

120 A or less at 11.5 V


If the result is not as specified, inspect the starter assembly.

HINT:

Inspect the starter brush holder assembly, starter yoke assembly and starter armature assembly. If there is a malfunction, replace the part and perform this test again.




Hide 28150 2.INSPECT MAGNET STARTER SWITCH ASSEMBLY

a.

Inspect the pull-in coil.

i.
A074034E03
2.844,1.302 3.083,1.521 3.083,1.521 3.156,1.521 false 1.417,1.156 1.583,0.76 1.583,0.76 1.646,0.76 false 1.698,0.698 1.875,0.854 0.177,0.156 10 false *2 3.208,1.438 3.396,1.594 0.188,0.156 10 false *1

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal C - Terminal 50 Always Below 1 Ω


Text in Illustration
*1 Terminal C
*2 Terminal 50

If the result is not as specified, replace the magnet starter switch assembly.



b.

Inspect the holding coil.

i.
A074035E03
2.479,0.979 1.927,0.26 1.927,0.26 1.813,0.26 true 1.417,1.167 1.521,0.729 1.521,0.729 1.635,0.729 false 1.625,0.188 1.823,0.354 0.198,0.167 10 false *1 1.688,0.656 1.885,0.823 0.198,0.167 10 false *2

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Switch body - Terminal 50 Always Below 2 Ω


Text in Illustration
*1 Switch Body
*2 Terminal 50

If the result is not as specified, replace the magnet starter switch assembly.



Hide 3.INSPECT BRUSH

a.
A385844E01
0.188,0.115 0.5,0.313 0.313,0.198 10 false *a 0.208,2.49 0.521,2.688 0.313,0.198 10 false *b 2.396,1.458 2.708,1.656 0.313,0.198 10 false *1 2.115,3.563 2.427,3.76 0.313,0.198 10 false *1

Using a vernier caliper, measure the brush length.

Text in Illustration
*1 Length
*a Brush Holder Side
*b Starter Yoke Side

Standard brush length:

16.5 mm (0.650 in.)


Minimum brush length:

9.0 mm (0.354 in.)


If the length is less than the minimum, replace the brush holder and starter yoke assembly.



Hide 28140 4.INSPECT STARTER BRUSH HOLDER ASSEMBLY

a.
P021088

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Positive (+) brush holder - Negative (-) brush holder Always 10 kΩ or higher


If the result is not as specified, replace the starter brush holder assembly.



b.

Check the brush spring load.

i.
ST00019E28
2.302,1.354 2.51,1.135 2.51,1.135 2.573,1.135 false 1.354,1.646 1.208,1.479 1.208,1.479 1.135,1.479 false 0.938,1.396 1.104,1.573 0.167,0.177 10 false *2 2.583,1.042 2.771,1.219 0.188,0.177 10 false *1

Take a pull scale reading immediately after the brush spring separates from the brush.

Standard spring load:

27 to 32 N (2.7 to 3.3 kgf, 6.0 to 7.3 lbf)


Minimum spring load:

18 N (2 kgf, 4.0 lbf)


Text in Illustration
*1 Brush Spring
*2 Brush

If the spring load is less than the minimum, replace the brush holder assembly.



Hide 28120 5.INSPECT STARTER YOKE ASSEMBLY

a.

Inspect for an open circuit.

i.
A222269

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Lead wire - Brush Always Below 1 Ω


If the result is not as specified, replace the starter yoke assembly.



b.

Inspect for a short circuit.

i.
A222270

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Starter yoke body - Brush Always 10 kΩ or higher


If the result is not as specified, replace the starter yoke assembly.



Hide 28160 6.INSPECT STARTER ARMATURE ASSEMBLY

a.

Check the commutator for dirt and/or burns on the surface.

If the surface is dirty or burnt, correct it with sandpaper (No. 400) or a lathe. Replace the armature if necessary.


b.

Inspect the commutator for an open circuit.

i.
ST01098E03
2.865,0.719 2.698,0.177 2.698,0.177 2.552,0.177 false 2.385,0.083 2.583,0.25 0.198,0.167 10 false *1

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Segment - Segment Always Below 1 Ω


Text in Illustration
*1 Segment

If the result is not as specified, replace the starter armature assembly.



c.

Inspect the commutator for a short circuit.

i.
ST01099E03
2.156,0.417 2.375,0.146 2.375,0.146 2.479,0.146 false 2.833,0.719 3,0.458 3,0.458 3.104,0.458 false 2.531,0.052 2.708,0.198 0.177,0.146 10 false *2 3.156,0.375 3.333,0.521 0.177,0.146 10 false *1

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Segment - Coil core Always 10 kΩ or higher


Text in Illustration
*1 Segment
*2 Coil Core

If the result is not as specified, replace the starter armature assembly.



d.
S004640

Inspect the commutator circle runout.

i.

Place the armature on V-blocks.


ii.

Using a dial indicator, measure the circle runout.

Maximum circle runout:

0.05 mm (0.00197 in.)


If the runout is more than the maximum, correct it with sandpaper (No. 400) or replace the starter armature assembly.



e.
ST01100

Using a vernier caliper, measure the commutator diameter.

Standard diameter:

35.0 mm (1.38 in.)


Minimum diameter:

34.0 mm (1.34 in.)


If the diameter is less than the minimum, replace the starter armature assembly.


f.
ST00040

Measure the undercut depth of the commutator.

Standard depth:

0.7 mm (0.0276 in.)


Minimum depth:

0.2 mm (0.00787 in.)


If the undercut depth is less than the minimum, correct it with a hacksaw blade.


g.

Inspect the bearings.

i.

Check that the bearing rotates smoothly.

If the result is not as specified, replace the starter armature assembly.



Hide 28011 7.INSPECT STARTER CLUTCH SUB-ASSEMBLY

a.
A223418

Rotate the pinion gear clockwise and check that it turns freely. Try to rotate the pinion gear counterclockwise and check that it locks.

Text in Illustration
V100135

Free
V100136

Lock

If the result is not as specified, replace the starter clutch sub-assembly.


b.

Turn the pinion gear by hand while applying inward force and check the movement of the bearing.

If resistance is felt or the bearing sticks, replace the starter clutch sub-assembly.