Home › Engine / Hybrid System › 1KD-FTV (STARTING) › STARTER (for 2.2 kW Type) › 2015.06–2020.08
RM27T0E _51 Engine / Hybrid System _053694 1KD-FTV STARTING _0260731 STARTER(for 2.2 kW Type) G

1KD-FTV STARTING  STARTER(for 2.2 kW Type)  INSPECTION  


PROCEDURE

Hide 28100 1.INSPECT STARTER

CAUTION:

As a large electric current passes through the cable during this inspection, a thick cable must be used. If not, the cable may become hot and cause injury.


NOTICE:

These tests must be performed within 3 to 5 seconds to prevent the coil from burning out.


a.

Mount the starter in a vise between aluminum plates.


b.

Perform pull-in test.

i.
A222485E01
2.043,0.031 2.254,0.187 0.211,0.156 10 *1 1.901,0.851 1.901,0.129 1.901,0.129 2.026,0.129 false

Remove the nut and disconnect the lead wire from terminal C.

Text in Illustration
*1 Terminal C


ii.
U169198E01
2.736,1.661 2.924,1.831 0.188,0.170 12 *1 1.821,3.922 2.009,4.092 0.188,0.170 12 *2 1.981,2.581 2.485,1.762 2.485,1.762 2.686,1.762 false

Connect the battery to the magnet starter switch as shown in the illustration. Then check that the clutch pinion gear moves outward.

Text in Illustration
*1 Terminal C
*2 Terminal 50

If the clutch pinion gear does not move, inspect the magnet starter switch assembly. If the magnet starter switch assembly is not as specified, replace it.



c.

Perform a holding test.

i.
A222487E01
2.832,2.017 3.016,2.180 0.184,0.163 10 *1 2.021,2.659 2.683,2.109 2.683,2.109 2.821,2.109 false

When the battery is connected as above with the clutch pinion gear out, disconnect the negative (-) lead from terminal C. Check that the pinion gear remains out.

Text in Illustration
*1 Terminal C

If the clutch pinion gear returns inward, inspect the magnet starter switch assembly. If the magnet starter switch assembly is not as specified, replace it.



d.

Inspect the clutch pinion gear return.

i.
A222488

Disconnect the negative (-) lead from the starter body. Check that the clutch pinion gear returns inward.

If the clutch pinion gear does not return inward, inspect the magnet starter switch assembly. If the magnet starter switch assembly is not as specified, replace it.



e.

Perform an operation test without load.

i.

Connect the lead wire to terminal C.

Torque:
5.9 N*m (60 kgf*cm, 52 in.*lbf)


ii.
A222489E01
2.614,1.976 2.784,2.155 0.170,0.179 10 *2 1.353,1.643 1.523,1.822 0.170,0.179 10 *1 1.829,1.629 1.631,1.726 1.631,1.726 1.528,1.726 false 2.281,1.626 2.416,2.068 2.416,2.068 2.591,2.068 false

Connect the battery and ammeter to the starter as shown in the illustration.


iii.

Check that the starter rotates smoothly and steadily while the pinion gear is extended. Then measure the current.

Standard current:

120 A or less at 11.5 V


Text in Illustration
*1 Terminal 50
*2 Terminal 30

If the result is not as specified, inspect the starter assembly

HINT:

Inspect the starter brush holder assembly, starter yoke assembly and starter armature assembly. If there is a malfunction, replace the part and perform this test again.




Hide 28150 2.INSPECT MAGNET STARTER SWITCH ASSEMBLY

a.
A121395E03
1.89,2.671 2.073,2.864 0.184,0.193 10 *1 2.943,2.407 3.099,2.600 0.156,0.193 10 *2 2.559,1.439 2.788,2.505 2.788,2.505 2.926,2.505 false 1.786,2.207 1.7,2.766 1.7,2.766 1.849,2.766 false

Check the pull-in coil for an open circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 50 - Terminal C Always Below 1 Ω


Text in Illustration
*1 Terminal 50
*2 Terminal C

If the result is not as specified, replace the magnet starter switch assembly.



b.
A121396E03
1.611,2.884 1.787,3.054 0.176,0.170 10 *1 2.065,2.402 1.954,2.973 1.954,2.973 1.803,2.973 false

Check the hold-in coil for an open circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 50 - Starter switch body Always Below 2 Ω


Text in Illustration
*1 Terminal 50

If the result is not as specified, replace the magnet starter switch assembly.



Hide 3.INSPECT BRUSH

A385844

a.

Using a vernier caliper, measure the brush length.

Standard length:

16.5 mm (0.650 in.)


Minimum length:

9.0 mm (0.354 in.)


If the length is less than the minimum, replace the starter brush holder assembly and starter yoke assembly.


Hide 28140 4.INSPECT STARTER BRUSH HOLDER ASSEMBLY

a.
A115033

Inspect the brush insulation.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Positive (+) brush holder - Negative (-) brush holder Always 10 kΩ or higher


If the result is not as specified, replace the starter brush holder assembly.



b.
A115032

Take a pull scale reading the instant the brush spring separates from the brush.

Standard spring load:

27 to 32 N (2.7 to 3.3 kgf, 5.9 to 7.3 lbf)


Minimum spring load:

18 N (1.8 kgf, 4.0 lbf)


If the spring load is less than the minimum, replace the starter brush holder assembly.


Hide 28120 5.INSPECT STARTER YOKE ASSEMBLY

a.
B000453

Inspect the field coil for open circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal C - Brush Always Below 1 Ω


If the result is not as specified, replace the starter yoke assembly.



b.
B000454

Inspect the field coil for a short circuit to ground.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal C - Starter yoke body Always 10 kΩ or higher


If the result is not as specified, replace the starter yoke assembly.



Hide 28160 6.INSPECT STARTER ARMATURE ASSEMBLY

a.

Check the commutator for dirt and/or burns on the surface.

If the surface is dirty or burnt, restore the surface with sandpaper (No. 400) or on a lathe. If necessary, replace the starter armature assembly.


b.
A115023E03
2.332,2.733 2.520,2.909 0.188,0.177 10 *1 1.964,2.337 2.177,2.83 2.177,2.83 2.319,2.83 false

Inspect the commutator for an open circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Segment - Segment Always Below 1 Ω


Text in Illustration
*1 Segment

If the result is not as specified, replace the starter armature assembly.



c.
A115024E03
2.25,2.819 2.425,2.982 0.175,0.163 10 *1 3.048,2.482 3.257,2.653 0.209,0.171 10 *2 1.935,2.36 2.124,2.91 2.124,2.91 2.239,2.91 false 2.764,2.194 2.921,2.572 2.921,2.572 3.033,2.572 false

Inspect the commutator for a short circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Segment - Coil core Always 10 kΩ or higher


Text in Illustration
*1 Segment
*2 Coil Core

If the result is not as specified, replace the starter armature assembly.



d.
A115025

Inspect the commutator circle runout.

i.

Place the armature on V-blocks.


ii.

Using a dial gauge, measure the circle runout.

Maximum circle runout:

0.05 mm (0.00197 in.)


If the circle runout is more than the maximum, replace the starter armature assembly.



e.
A115026

Using a vernier caliper, measure the commutator diameter.

Standard commutator diameter:

35.0 mm (1.38 in.)


Minimum commutator diameter:

34.0 mm (1.34 in.)


If the diameter is less than the minimum, replace the starter armature assembly.


f.
A115027

Using a vernier caliper, measure the undercut depth of the commutator.

Standard undercut depth:

0.7 mm (0.0276 in.)


Minimum undercut depth:

0.2 mm (0.00787 in.)


If the undercut depth is less than the minimum, replace the starter armature assembly.


g.

Inspect the bearings.

i.

Check that the bearings rotate smoothly.

If the result is not as specified, replace the starter armature assembly.



Hide 28011 7.INSPECT STARTER CLUTCH SUB-ASSEMBLY

a.
A115056

Rotate the pinion gear clockwise and check that it turns freely. Try to rotate the pinion gear counterclockwise and check that it locks.

Text in Illustration
V100135

Free
V100136

Lock

If the result is not as specified, replace the starter brush holder assembly.


b.

Turn the pinion gear by hand while applying inward force and check the movement of the bearing.

If the result is not as specified, replace the starter brush holder assembly.