Home › Engine / Hybrid System › 1KD-FTV (STARTING) › STARTER (for 2.2 kW Type) › 2015.06–2020.08
RM27T0E _51 Engine / Hybrid System _053694 1KD-FTV STARTING _0260731 STARTER(for 2.2 kW Type) A

1KD-FTV STARTING  STARTER(for 2.2 kW Type)  REASSEMBLY  


PROCEDURE

Hide 28011 1.INSTALL STARTER CLUTCH ASSEMBLY

a.

Apply high temperature grease to the steel ball, return spring, clutch roller, retainer, pinion gear and idler gear.


b.
A222255

Insert the steel ball into the starter clutch hole.


c.

Insert the return spring into the starter clutch hole.


d.
U169205E02
1.74,0.448 1.823,0.219 1.823,0.219 1.906,0.219 false 2.052,0.74 2.198,0.229 2.198,0.229 2.292,0.229 false 2.469,0.844 2.573,0.406 2.573,0.406 2.656,0.406 false 2.781,1.521 2.875,1.271 2.875,1.271 2.979,1.271 false 1.969,1.667 1.729,1.802 1.729,1.802 1.635,1.802 false 0.656,1.167 0.438,0.719 0.438,0.719 0.344,0.719 false 1.938,0.135 2.104,0.302 0.167,0.167 10 false *4 2.302,0.146 2.469,0.313 0.167,0.167 10 false *3 2.708,0.333 2.875,0.5 0.167,0.167 10 false *5 3.052,0.354 3.219,0.521 0.167,0.167 10 false *6 3.01,1.198 3.177,1.365 0.167,0.167 10 false *1 1.438,1.719 1.604,1.885 0.167,0.167 10 false *2 0.156,0.625 0.323,0.792 0.167,0.167 10 false *7

Install the starter clutch, idler gear, pinion gear, retainer and clutch roller to the starter housing.

Text in Illustration
*1 Return Spring
*2 Starter Clutch
*3 Idler Gear
*4 Pinion Gear
*5 Retainer
*6 Clutch Roller
*7 Starter Housing


e.
A102596

Install the starter housing to the magnet switch with the 2 bolts.

Torque:
9.3 N*m (95 kgf*cm, 82 in.*lbf)


Hide 28160 2.INSTALL STARTER ARMATURE ASSEMBLY

a.

Apply high temperature grease to the starter armature bearing.


b.
P004699

Using a press, press the starter armature into the starter yoke.


Hide 28140 3.INSTALL STARTER BRUSH HOLDER ASSEMBLY

a.
ST00096E08
1.969,1.813 1.865,1.813 1.865,1.813 1.656,1.51 false 1.667,1.375 2.406,0.323 2.406,0.323 2.51,0.323 false 2.583,0.25 2.771,0.396 0.188,0.146 10 false *1 2.01,1.74 2.177,1.906 0.167,0.167 10 false *2

Align the claw of the brush holder with the groove of the starter yoke.

Text in Illustration
*1 Groove
*2 Claw


b.

Place the brush holder on the starter yoke.


c.

Install the 4 starter yoke brushes to the starter brush holder.

i.

Using a screwdriver, pull back the spring.


ii.

Install the brush to the brush holder.

NOTICE:

Make sure that the positive (+) lead wires are not grounded.




Hide 28120 4.INSTALL STARTER YOKE ASSEMBLY

a.

Install a new O-ring to the groove of the starter yoke.


b.
P005017E03
1.396,0.24 1.594,0.24 1.594,0.24 1.833,0.365 true 0.26,0.958 0.417,0.958 0.417,0.958 0.719,1.594 true 1.365,1.656 1.969,2.094 1.969,2.094 2.125,2.094 true 2.198,1.99 2.375,2.135 0.177,0.146 10 false *1 0.083,0.875 0.229,1.042 0.146,0.167 10 false *2 1.188,0.177 1.365,0.333 0.177,0.156 10 false *3

Align the claws of the starter brush holder with the grooves of the magnet starter switch and install the starter yoke and starter armature.

Text in Illustration
*1 Groove
*2 Claw
*3 Punch Mark


c.

Align the punch mark of the starter yoke with the line of the magnet starter switch.


d.
S004229

Install 2 new O-rings to the bolts.

Text in Illustration
*1 O-Ring


e.

Install the starter yoke with the 2 bolts.

Torque:
13 N*m (130 kgf*cm, 9 ft.*lbf)


f.

Connect the lead wire to terminal C with the nut.

Torque:
5.9 N*m (60 kgf*cm, 52 in.*lbf)