Home › Engine / Hybrid System › 1KD-FTV (STARTING) › STARTER (for 2.7 kW Type) › 2015.06–2020.08
RM27T0E _51 Engine / Hybrid System _053694 1KD-FTV STARTING _0260732 STARTER(for 2.7 kW Type) A

1KD-FTV STARTING  STARTER(for 2.7 kW Type)  REASSEMBLY  


PROCEDURE

Hide 28160 1.INSTALL STARTER ARMATURE ASSEMBLY

Install the starter armature to the starter yoke.

A158310

Hide 28140 2.INSTALL STARTER BRUSH HOLDER ASSEMBLY

a.

Place the starter brush holder on the starter yoke.


b.
A102629

Install the starter brushes to the starter brush holder.

i.

Using a screwdriver, pull back spring.


ii.

Install the brush to the brush holder.

NOTICE:

Make sure that the positive (+) lead wires are not grounded.




c.
A102628

Install the commutator end frame with the 2 screws.

Torque:
3.6 N*m (37 kgf*cm, 32 in.*lbf)


Hide 28150 3.INSTALL MAGNET STARTER SWITCH ASSEMBLY

a.

Apply high temperature grease to the steel ball, return spring, clutch roller, retainer and idler gear.


b.
A197147

Insert the steel ball into the starter clutch hole.


c.

Insert the return spring into the starter clutch hole.


d.
A385845E02
0.271,0.708 0.49,0.708 0.49,0.708 0.583,1.031 false 0.969,0.313 1.188,0.313 1.188,0.313 1.281,0.635 false 1.031,1.813 1.052,1.927 1.052,1.927 1.208,1.927 false 1.438,1.708 1.49,1.979 1.49,1.979 1.656,1.979 false 1.865,1.667 1.969,2.021 1.969,2.021 2.25,2.021 false 3.01,1.813 2.823,1.813 2.823,1.813 2.708,1.479 false 0.104,0.625 0.417,0.823 0.313,0.198 10 false *1 1.26,1.854 1.573,2.052 0.313,0.198 10 false *5 2.281,1.938 2.594,2.135 0.313,0.198 10 false *3 1.729,1.896 2.042,2.094 0.313,0.198 10 false *4 0.781,0.24 1.094,0.438 0.313,0.198 10 false *2 3.073,1.76 3.385,1.958 0.313,0.198 10 false *6

Install the starter clutch, idler gear, retainer and clutch roller to the starter housing.

Text in Illustration
*1 Return Spring
*2 Starter Clutch
*3 Idler Gear
*4 Retainer
*5 Clutch Roller
*6 Starter Housing


e.
A102626

Install the magnet starter switch with the 3 screws.

Torque:
9.3 N*m (95 kgf*cm, 82 in.*lbf)


Hide 28120 4.INSTALL STARTER YOKE ASSEMBLY

a.

Install the felt washer to the starter armature.


b.
A102643E02
1.786,1.399 1.951,1.554 0.165,0.155 10 *1 1.287,1.776 1.448,1.925 0.161,0.149 10 *2 0.585,1.7 1.26,1.853 false 2.837,1.482 1.975,1.483 false

Align the claw of the starter yoke with the groove of the starter switch and install the starter yoke to the starter switch.


c.

Install the starter yoke to the starter switch.

Text in Illustration
*1 Claw
*2 Groove


d.
A115884E03
0.84,1.654 1.027,1.821 0.187,0.167 10 *1 1.051,1.709 1.714,1.512 false

Install the 2 through bolts.

Torque:
9.3 N*m (95 kgf*cm, 82 in.*lbf)


e.

Connect the lead wire to terminal C with the nut.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)

Text in Illustration
*1 Terminal C