Home › Engine / Hybrid System › 1KD-FTV (STARTING) › STARTER (for 3.0 kW Type) › 2015.06–2020.08
RM27T0E _51 Engine / Hybrid System _053694 1KD-FTV STARTING _0260733 STARTER(for 3.0 kW Type) A

1KD-FTV STARTING  STARTER(for 3.0 kW Type)  REASSEMBLY  


PROCEDURE

Hide 28011 1.INSTALL STARTER CLUTCH SUB-ASSEMBLY

a.

Apply high temperature grease to the steel ball, return spring, clutch roller, retainer, pinion gear and idler gear.


b.
A197147

Insert the steel ball into the starter clutch hole.


c.

Insert the return spring into the starter clutch hole.


d.
A102601E04
1.458,0.531 1.135,0.219 1.135,0.219 1,0.219 false 1.406,0.854 1,0.458 1,0.458 0.875,0.458 false 1.146,0.99 0.865,0.698 0.865,0.698 0.729,0.698 false 0.906,1.24 0.781,1.385 0.781,1.385 0.677,1.385 false 0.656,1.813 0.729,1.979 0.729,1.979 0.844,1.979 false 1.448,1.76 1.604,1.958 1.604,1.958 1.76,1.958 false 2.594,0.438 2.75,0.281 2.75,0.281 2.875,0.281 false 0.792,0.125 0.958,0.271 0.167,0.146 10 false *2 0.698,0.375 0.865,0.521 0.167,0.146 10 false *3 0.563,0.635 0.729,0.781 0.167,0.146 10 false *5 0.5,1.313 0.667,1.458 0.167,0.146 10 false *4 0.854,1.885 1.021,2.031 0.167,0.146 10 false *1 1.792,1.885 1.958,2.031 0.167,0.146 10 false *6 2.875,0.177 3.042,0.333 0.167,0.156 10 false *7

Install the starter clutch, return spring, idler gear, pinion gear, retainer and clutch roller.

Text in Illustration
*1 Return Spring
*2 Idler Gear
*3 Pinion Gear
*4 Clutch Roller
*5 Retainer
*6 Starter Clutch
*7 Starter Housing


e.
A102600

Install the starter housing to the magnet starter switch with the 3 screws.

Torque:
11 N*m (112 kgf*cm, 8 ft.*lbf)


Hide 28160 2.INSTALL STARTER ARMATURE ASSEMBLY

a.
A102618

Apply high-temperature grease to the armature bearings.


b.

Using a press, press the armature into the commutator end frame.


c.

Install a new O-ring to the starter yoke.


d.
A102619E02
1.416,1.3 1.597,1.442 0.180,0.142 10 *2 0.559,0.05 0.771,0.192 0.211,0.142 10 *1 1.871,0.391 0.861,0.146 0.861,0.146 0.775,0.146 false 1.918,1.044 1.716,1.383 1.716,1.383 1.63,1.383 false

Align the groove of the commutator end frame with the claw of the starter yoke, and install the armature and commutator end frame.

Text in Illustration
*1 Groove
*2 Claw


Hide 28140 3.INSTALL STARTER BRUSH HOLDER ASSEMBLY

a.
A102620E02
0.518,0.345 0.699,0.489 0.182,0.144 10 *2 1.156,1.684 1.360,1.836 0.204,0.153 10 *1 1.695,1.392 0.844,0.425 0.844,0.425 0.728,0.425 false 1.686,1.495 1.458,1.783 1.458,1.783 1.36,1.783 false

Align the claw of the starter brush holder with the groove of the starter yoke.

Text in Illustration
*1 Groove
*2 Claw


b.

Place the starter brush holder on the starter yoke.


c.
A102621

Connect the 4 brushes to the starter brush holder.

i.

Using a screwdriver, pull back the spring.


ii.

Connect the brush to the brush holder.

NOTICE:

Make sure that the positive (+) lead wires are not grounded.




d.

Install a new O-ring to the starter yoke.


Hide 28120 4.INSTALL STARTER YOKE ASSEMBLY

a.
A102623E01
0.89,0.447 1.045,0.595 0.155,0.148 10 *1 1.097,0.532 1.191,0.532 1.191,0.532 1.422,0.739 false 1.991,1.207 2.160,1.363 0.169,0.156 10 *2 2.228,1.284 2.296,1.284 2.296,1.284 2.637,0.419 false

Align the claw of the starter brush holder with the groove of the magnet starter switch and install the starter yoke to the magnet starter switch.

Text in Illustration
*1 Claw
*2 Groove


b.

Install the starter yoke to the starter housing with the 2 bolts.

Torque:
14 N*m (145 kgf*cm, 10 ft.*lbf)


c.

Connect the lead wire to terminal C with the nut.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)