28100
1.INSPECT STARTER ASSEMBLY
As a large electric current passes through the cable during this inspection, a thick cable must be used. If not, the cable may become hot and cause injury.
These tests must be performed within 3 to 5 seconds to prevent the coil from burning out.
Mount the starter assembly in a vise between aluminum plates.
Perform a pull-in test.
Remove the nut and disconnect the lead wire from terminal C.
Connect the battery to the starter assembly as shown in the illustration. Check that the clutch pinion gear extends.
| *a | Terminal C |
| *b | Terminal 50 |
|
Extends |
If the clutch pinion gear does not extend, replace the magnet starter switch assembly.
Perform a holding test.
Disconnect the negative (-) lead from terminal C with the condition specified in the pull-in test above being maintained. Check that the clutch pinion gear remains out.
|
Disconnect |
If the clutch pinion gear returns inward, replace the magnet starter switch assembly.
Inspect the clutch pinion gear return.
Disconnect the negative (-) lead from the starter body. Check that the clutch pinion gear returns inward.
|
Disconnect |
|
Return Inward |
If the clutch pinion gear does not return inward, replace the magnet starter switch assembly.
Perform an operation test without load.
Connect the lead wire to terminal C with the nut.
Connect the battery and an ammeter (AC/DC 400A probe) to the starter assembly as shown in the illustration.
150 A or less at 11.5 V
| *a | Terminal 30 |
| *b | Terminal 50 |
| *c | AC/DC 400A Probe |
If the result is not as specified, replace the starter assembly.
28150
2.INSPECT MAGNET STARTER SWITCH ASSEMBLY
Push in the plunger and check that it returns quickly to its original position.
If the result is not as specified, replace the magnet starter switch assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Terminal 50 - Terminal C | Always | Below 1 Ω |
| Terminal 50 - Switch Body | Below 2 Ω |
| *a | Terminal C |
| *b | Terminal 50 |
| *c | Switch Body |
If the result is not as specified, replace the magnet starter switch assembly.
28140
3.INSPECT STARTER BRUSH HOLDER ASSEMBLY
Check the resistance.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A - B | Always | Below 1 Ω |
| C - D | ||
| D - E |
If the result is not as specified, replace the starter brush holder assembly.
Check the brush length.
Using a vernier caliper, measure the brush length.
10.4 mm (0.409 in.)
5.0 mm (0.197 in.)
| *a | Length |
28160
4.INSPECT STARTER ARMATURE ASSEMBLY
Check the commutator surface for dirt and burns.
If the surface is dirty or burnt, replace the starter armature assembly.
Check the resistance.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Segment - Segment | Always | Below 1 Ω |
| Segment - Coil Core | 10 kΩ or higher |
| *a | Segment |
| *b | Coil Core |
If the result is not as specified, replace the starter armature assembly.
Check the commutator for circle runout.
Place the commutator on V-blocks.
Using a dial indicator, measure the circle runout.
0.05 mm (0.00197 in.)
If the runout is more than the maximum, replace the starter armature assembly.
Check the commutator.
Using a vernier caliper, measure the commutator diameter.
29.0 mm (1.14 in.)
28.0 mm (1.10 in.)
Be sure to measure the commutator diameter at the ridges.
If the diameter is less than the minimum, replace the starter armature assembly.
Using a vernier caliper, measure the undercut depth of the commutator.
0.7 mm (0.0276 in.)
0.4 mm (0.0157 in.)
Be sure to measure the commutator diameter at the ridges.
If the undercut depth is less than the minimum, replace the starter armature assembly.
28011
5.INSPECT REPAIR SERVICE STARTER KIT
Check the clutch pinion gear teeth for wear or damage.
If the clutch pinion gear teeth are damaged, replace the repair service starter kit and also inspect the flywheel ring gear for wear or damage.
Rotate the clutch pinion gear clockwise and check that it turns freely. Try to rotate the clutch pinion gear counterclockwise and check that it locks.
|
Free |
|
Lock |
If the result is not as specified, replace the repair service starter kit.