28100
1.INSPECT STARTER ASSEMBLY
As a large electric current passes through the cable during this inspection, a thick cable must be used. If not, the cable may become hot and cause injury.
The following tests must be done within 3 to 5 seconds to prevent the coil from burning out.
Mount the starter assembly in a vise between aluminum plates.
Perform a pull-in test.
Remove the nut and disconnect the lead wire from terminal C.
Connect the battery to the starter assembly as shown in the illustration. Check that the clutch pinion gear extends.
| *a | Terminal C |
| *b | Terminal 50 |
|
Extends |
If the clutch pinion gear does not move, inspect the magnet starter switch assembly. If the magnet starter switch assembly is not as specified, replace it.
Perform a holding test.
Disconnect the negative (-) lead from terminal C with the condition specified in the pull-in test above being maintained. Check that the clutch pinion gear remains out.
|
Disconnect |
If the clutch pinion gear returns inward, replace the magnet starter switch assembly.
Inspect the clutch pinion gear return.
Disconnect the negative (-) lead from the starter body. Check that the clutch pinion gear returns inward.
|
Disconnect |
|
Returns Inward |
If the clutch pinion gear does not return inward, replace the magnet starter switch assembly.
Perform an operation test without load.
Connect the lead wire to terminal C with the nut.
Connect the battery and an ammeter (AC/DC 400 A Probe) to the starter assembly as shown in the illustration.
| *a | Terminal 50 |
| *b | Terminal 30 |
| *c | AC/DC 400 A Probe |
|
Connect |
Connect the battery and an ammeter to the starter assembly as shown in the illustration.
Check that the starter rotates smoothly and steadily while the clutch pinion gear is extended. Then measure the current.
180 A or less at 11.0 V
If the result is not as specified, replace the starter assembly.
28150
2.INSPECT MAGNET STARTER SWITCH ASSEMBLY
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Terminal 50 - Terminal C | Always | Below 1 Ω |
| Terminal 50 - Switch Body | Below 2 Ω |
| *a | Terminal C |
| *b | Terminal 50 |
| *c | Switch Body |
If the result is not as specified, replace the magnet starter switch assembly.
28140
3.INSPECT STARTER BRUSH HOLDER ASSEMBLY
Inspect the load of the brush spring.
Take a pull scale reading immediately after the brush spring separates from the brush.
26 to 45 N (3 to 5 kgf, 5.8 to 10.1 lbf)
12 N (1 kgf, 2.7 lbf)
If the spring load is less than the minimum, replace the starter brush holder assembly.
Check the resistance.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Positive (+) Brush Holder - Negative (-) Brush Holder | Always | 10 kΩ or higher |
If the result is not as specified, replace the starter brush holder assembly.
Check the brush length.
Using a vernier caliper, measure the brush length.
20.5 mm (0.814 in.)
11.0 mm (0.433 in.)
| *a | Length |
If the length is less than the minimum, replace the starter brush holder assembly.
28120
4.INSPECT STARTER YOKE ASSEMBLY
Check the resistance.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Lead Wire - Brush | Always | Below 1 Ω |
| Starter Yoke Body - Brush | 10 kΩ or higher |
| *a | Lead Wire |
| *b | Brush |
| *c | Starter Yoke Body |
If the result is not as specified, replace the starter yoke assembly.
Check the brush length.
Using a vernier caliper, measure the brush length.
20.5 mm (0.814 in.)
11.0 mm (0.433 in.)
| *a | Length |
If the length is less than the minimum, replace the starter starter yoke assembly.
28160
5.INSPECT STARTER ARMATURE ASSEMBLY
Check the commutator for dirt and/or burns on the surface.
If the surface is dirty or burnt, correct it with sandpaper (No. 400) or a lathe.
Check the resistance.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Segment - Segment | Always | Below 1 Ω |
| Segment - Coil Core | 10 kΩ or higher |
| *a | Segment |
| *b | Coil Core |
If the result is not as specified, replace the starter armature assembly.
Check the commutator circle runout.
Place the armature on V-blocks.
Using a dial indicator, measure the circle runout.
0.05 mm (0.00197 in.)
If the circle runout is more than the maximum, replace the starter armature assembly.
Check the commutator.
If the diameter is less than the minimum, replace the starter armature assembly.
Using a vernier caliper, measure the commutator diameter.
36.0 mm (1.42 in.)
35.0 mm (1.38 in.)
If the diameter is less than the minimum, replace the starter armature assembly.
Using a dial indicator, measure the undercut depth of the commutator.
0.7 mm (0.0276 in.)
0.2 mm (0.00787 in.)
If the undercut depth is less than the minimum, correct it with a hacksaw blade.
Inspect the armature bearings.
Check that the armature bearings rotate smoothly.
If the result is not as specified, replace the starter armature assembly.
28011
6.INSPECT STARTER CLUTCH SUB-ASSEMBLY
Rotate the clutch pinion gear clockwise and check that it turns freely. Try to rotate the clutch pinion gear counterclockwise and check that it locks.
|
Free |
|
Lock |
If the result is not as specified, replace the starter clutch sub-assembly.
Turn the pinion gear by hand while applying inward force and check the movement of the bearing.
If resistance is felt or the bearing sticks, replace the starter clutch sub-assembly.