Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053696 CRUISE CONTROL _0260748 DYNAMIC RADAR CRUISE CONTROL SYSTEM U

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  TERMINALS OF ECU  


CHECK DRIVING SUPPORT ECU


U170576E03
3.49,0.281 3.854,0.427 0.365,0.146 10 false G119

NOTICE:
·

As disconnecting the connector to perform inspections may cause DTCs to be stored, clear DTCs after performing inspections.

·

As the connector may be damaged if a load of more than 10 kg (22 lb) is applied to it, do not apply any more load than necessary to the connector.



a.

Disconnect the G119 ECU connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G119-30 (B) - Body ground G - Body ground ECU power source circuit Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
G119-25 (GND) - Body ground BR - Body ground Ground Always Below 1 Ω


c.

Reconnect the G119 ECU connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G119-7 (MODE) - Body ground SB - Body ground Distance control switch signal Ignition switch ON, distance control switch off 11 to 14 V
Ignition switch ON, distance control switch on Below 1 V
G119-32 (WIP2) - Body ground P - Body ground Windshield wiper switch circuit Ignition switch ON, windshield wiper switch Hi 11 to 14 V
Ignition switch ON, windshield wiper switch Lo Approximately 9 V
Ignition switch ON, windshield wiper switch off Below 1 V



CHECK ECM (for 1GR-FE)


U149279E05
1.188,0.198 1.542,0.469 0.354,0.271 10 false G55 2.021,0.198 2.448,0.469 0.427,0.271 10 false G56 3.333,0.198 3.698,0.448 0.365,0.25 10 false C34 4.042,0.198 4.438,0.469 0.396,0.271 10 false C35 4.833,0.208 5.281,0.51 0.448,0.302 10 false C36 5.729,0.198 6.198,0.552 0.469,0.354 10 false C37

a.

Disconnect the C36, G55 and G56 ECM connectors.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G55-24 (BATT) - Body ground L - Body ground Power source circuit Always 11 to 14 V
G55-21 (IGSW) - Body ground W - Body ground IG power source circuit Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
G56-34 (ST1-) - Body ground B - Body ground Stop light switch signal circuit Ignition switch ON, brake pedal released 11 to 14 V
Ignition switch ON, brake pedal depressed Below 1 V
G56-35 (STP) - Body ground V - Body ground Stop light switch signal circuit Brake pedal depressed 11 to 14 V
Brake pedal released Below 1 V
G56-1 (CCS) - Body ground B - Body ground Cruise control switch circuit Cruise control switch on Below 2.5 Ω
Cruise control switch off 10 kΩ or higher
+RES switch held on 235 to 245 Ω
-SET switch held on 617 to 643 Ω
CANCEL switch held on 1509 to 1571 Ω
G56-16 (CCHG) - Body ground V - Body ground Cruise control switch circuit Cruise control switch on MODE switch held on Below 2.5 Ω
Cruise control switch on MODE switch held off 1 MΩ or higher
C36-12 (E1) - Body ground BR - Body ground Ground Always Below 1 Ω


c.

Reconnect the C36, G55 and G56 ECM connectors.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G56-22 (S) - Body ground V - Body ground Transmission control switch circuit Ignition switch ON, shift lever in S 11 to 14 V
Ignition switch ON, shift lever not in S Below 1 V
G56-15 (SFTU) - Body ground GR - Body ground Transmission control switch circuit Ignition switch ON, shift lever in S → shift lever moved to "+" 11 to 14 V → Below 1 V
G56-9 (SFTD) - Body ground LG - Body ground Transmission control switch circuit Ignition switch ON, shift lever in S → shift lever moved to "-" 11 to 14 V → Below 1 V
C34-22 (D) - Body ground B - Body ground Park/neutral position switch signal Ignition switch ON, shift lever in D 11 to 14 V
Ignition switch ON, shift lever not in D Below 1 V
C34-27 (P) - Body ground L - Body ground Park/neutral position switch signal Ignition switch ON, shift lever in P 11 to 14 V
Ignition switch ON, shift lever not in P Below 1 V
C34-28 (R) - Body ground R - Body ground Park/neutral position switch signal Ignition switch ON, shift lever in R 11 to 14 V
Ignition switch ON, shift lever not in R Below 1 V
C34-21 (N) - Body ground G - Body ground Park/neutral position switch signal Ignition switch ON, shift lever in N 11 to 14 V
Ignition switch ON, shift lever not in N Below 1 V



CHECK ECM (for 1KD-FTV)


U170622E04
1.188,0.198 1.542,0.479 0.354,0.281 10 false G57 2.021,0.188 2.458,0.469 0.438,0.281 10 false G58 3.323,0.188 3.708,0.469 0.385,0.281 10 false C90 4.073,0.188 4.458,0.469 0.385,0.281 10 false C91 4.813,0.188 5.198,0.469 0.385,0.281 10 false C92 5.708,0.188 6.115,0.469 0.406,0.281 10 false C93

a.

Disconnect the C93, G57 and G58 ECM connectors.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G57-23 (BATT) - Body ground L - Body ground Power source circuit Always 11 to 14 V
G58-24 (IGSW) - Body ground W - Body ground IG power source circuit Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
G57-9 (ST1-) - Body ground B - Body ground Stop light switch signal circuit Ignition switch ON, brake pedal released 11 to 14 V
Ignition switch ON, brake pedal depressed Below 1 V
G57-8 (STP) - Body ground V - Body ground Stop light switch signal circuit Brake pedal depressed 11 to 14 V
Brake pedal released Below 1 V
G57-14 (CCS) - Body ground B - Body ground Cruise control switch circuit Cruise control switch on Below 2.5 Ω
Cruise control switch off 10 kΩ or higher
+RES switch held on 235 to 245 Ω
-SET switch held on 617 to 643 Ω
CANCEL switch held on 1509 to 1571 Ω
G58-9 (CCHG) - Body ground V - Body ground Cruise control switch circuit Cruise control switch on MODE switch held on Below 2.5 Ω
Cruise control switch on MODE switch held off 1 MΩ or higher
C93-1 (E1) - Body ground BR - Body ground Ground Always Below 1 Ω



CHECK TRANSMISSION CONTROL ECU (for 1KD-FTV)


U170647E03
2.167,0.313 2.521,0.625 0.354,0.313 10 false G69 3.521,0.313 3.865,0.542 0.344,0.229 10 false G71 4.802,0.313 5.188,0.542 0.385,0.229 10 false G70

a.

Disconnect the G70 ECU connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G70-5 (BATT) - Body ground L - Body ground Power source circuit Always 11 to 14 V
G70-6 (IG2) - Body ground B - Body ground IG power source circuit Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V


c.

Reconnect the G70 ECU connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G70-15 (S) - Body ground V - Body ground Transmission control switch circuit Ignition switch ON, shift lever in S 11 to 14 V
Ignition switch ON, shift lever not in S Below 1 V
G70-22 (SFTU) - Body ground GR - Body ground Transmission control switch circuit Ignition switch ON, shift lever in S → shift lever moved to "+" 11 to 14 V → Below 1 V
G70-23 (SFTD) - Body ground LG - Body ground Transmission control switch circuit Ignition switch ON, shift lever in S → shift lever moved to "-" 11 to 14 V → Below 1 V
G71-8 (D) - Body ground B - Body ground Park/neutral position switch signal Ignition switch ON, shift lever in D 11 to 14 V
Ignition switch ON, shift lever not in D Below 1 V
G69-13 (P) - Body ground L - Body ground Park/neutral position switch signal Ignition switch ON, shift lever in P 11 to 14 V
Ignition switch ON, shift lever not in P Below 1 V
G71-9 (R) - Body ground R - Body ground Park/neutral position switch signal Ignition switch ON, shift lever in R 11 to 14 V
Ignition switch ON, shift lever not in R Below 1 V
G69-14 (N) - Body ground G - Body ground Park/neutral position switch signal Ignition switch ON, shift lever in N 11 to 14 V
Ignition switch ON, shift lever not in N Below 1 V



CHECK ECM (for 1GD-FTV)


U170760E03
0.667,0.26 1.073,0.427 0.406,0.167 10 false C149 1.792,0.26 2.198,0.427 0.406,0.167 10 false C150 2.927,0.26 3.333,0.427 0.406,0.167 10 false C151 4.021,0.26 4.427,0.427 0.406,0.167 10 false C152 5.052,0.26 5.458,0.427 0.406,0.167 10 false G184 6.229,0.26 6.635,0.427 0.406,0.167 10 false G185

a.

Disconnect the C152 and G185 ECU connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G185-1 (BATT) - Body ground L - Body ground Power source circuit Always 11 to 14 V
G185-18 (IGSW) - Body ground W - Body ground IG power source circuit Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
G185-12 (ST1-) - Body ground B - Body ground Stop light switch signal circuit Ignition switch ON, brake pedal released 11 to 14 V
Ignition switch ON, brake pedal depressed Below 1 V
G185-13 (STP) - Body ground V - Body ground Stop light switch signal circuit Brake pedal depressed 11 to 14 V
Brake pedal released Below 1 V
G185-26 (CCS) - Body ground B - Body ground Cruise control switch circuit Cruise control switch on Below 2.5 Ω
Cruise control switch off 10 kΩ or higher
+RES switch held on 235 to 245 Ω
-SET switch held on 617 to 643 Ω
CANCEL switch held on 1509 to 1571 Ω
G185-11 (CCHG) - Body ground V - Body ground Cruise control switch circuit Cruise control switch on MODE switch held on Below 2.5 Ω
Cruise control switch on MODE switch held off 1 MΩ or higher
C152-1 (E1) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the C152 and G185 ECM connectors.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G184-13 (S) - Body ground V - Body ground Transmission control switch circuit Ignition switch ON, shift lever in S 11 to 14 V
Ignition switch ON, shift lever not in S Below 1 V
G184-21 (SFTU) - Body ground GR - Body ground Transmission control switch circuit Ignition switch ON, shift lever in S → shift lever moved to "+" 11 to 14 V → Below 1 V
G184-20 (SFTD) - Body ground LG - Body ground Transmission control switch circuit Ignition switch ON, shift lever in S → shift lever moved to "-" 11 to 14 V → Below 1 V
C149-14 (D) - Body ground B - Body ground Park/neutral position switch signal Ignition switch ON, shift lever in D 11 to 14 V
Ignition switch ON, shift lever not in D Below 1 V
C149-12 (P) - Body ground L - Body ground Park/neutral position switch signal Ignition switch ON, shift lever in P 11 to 14 V
Ignition switch ON, shift lever not in P Below 1 V
C149-15 (R) - Body ground R - Body ground Park/neutral position switch signal Ignition switch ON, shift lever in R 11 to 14 V
Ignition switch ON, shift lever not in R Below 1 V
C149-13 (N) - Body ground G - Body ground Park/neutral position switch signal Ignition switch ON, shift lever in N 11 to 14 V
Ignition switch ON, shift lever not in N Below 1 V