Home › Drivetrain › A750F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION FLUID › 2015.06–2017.08
RM27T0E _52 Drivetrain _053697 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0260754 AUTOMATIC TRANSMISSION FLUID A

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION FLUID  REPLACEMENT  


PROCEDURE

Hide 1.REPLACE AUTOMATIC TRANSMISSION FLUID

a.

Lift the vehicle. [*1]

NOTICE:

Set the vehicle on a lift so that the vehicle is kept level when it is lifted up (make sure that the tilt angle from the front to rear of the vehicle is within +/-1°).



b.

Remove the drain plug and gasket, and drain the ATF. [*2]


c.

Temporarily install the gasket and drain plug. [*3]

HINT:

Reuse the old gasket. A new gasket will be installed in step [*15].



d.
C112857E03
1.811,2.066 2.494,2.259 0.684,0.193 10 Refill Plug 0.337,4.159 1.270,4.350 0.934,0.191 10 Overflow Plug 1.477,3.637 0.921,4.159 false 1.387,0.078 2.070,0.271 0.684,0.193 10 Refill Hole 1.342,0.172 0.786,1.278 false 1.791,2.151 1.111,1.601 false

Remove the refill plug and overflow plug. [*4]


e.
C358120E01
1.802,0.844 2.667,1 2.667,1 2.667,1.167 true 0.531,0.802 0.438,1.083 0.438,1.083 0.438,1.25 false 2.25,1.167 3.167,1.333 0.917,0.167 10 false Overflow Tube 0.031,1.25 1.365,1.458 1.333,0.208 10 false Specified Fluid Level

Add fluid to the refill hole until it flows out of the overflow plug hole. [*5]

NOTICE:

Use Toyota Genuine ATF WS.



f.

Wait until the fluid flow slows and only drops come out. [*6]


g.

Temporarily install the gasket and overflow plug. [*7]

HINT:

Reuse the old gasket. The plug will be removed again to adjust the fluid level.



h.

Add fluid to the refill hole using the amount of fluid specified for removal and installation of the oil pan. [*8]

HINT:

Specified amount of fluid is 1.7 liters (1.8 US qts, 1.5 Imp. qts).



i.

Temporarily install the gasket and refill plug to avoid fluid spillage. [*9]

HINT:

Reuse the old gasket. The plug will be removed again to adjust the fluid level.



j.

Lower the vehicle. [*10]


k.

Start the engine. [*11]

NOTICE:

Make sure that the A/C switch is off.



l.

Slowly move the shift lever from P to S, and then change the gear from 1st to 5th. Then back to P. [*12]


m.

Allow the engine to idle for 30 seconds to warm it up. [*13]


n.

Turn the ignition switch off. [*14]


o.

Repeat steps [*1] to [*14].


p.

Repeat steps [*1] to [*2].


q.

Install a new gasket and the drain plug. [*15]

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


r.

Repeat steps [*4] to [*10].



t.

Lower the vehicle.


u.

Operation complete.