Home › Drivetrain › A750F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM (for 1KD-FTV) › 2015.06–2020.08
RM27T0E _52 Drivetrain _053697 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0260766 AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV) J

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV)  Transmission Control Switch Circuit  


DESCRIPTION

After moving the shift lever to S, it is possible to switch the shift range between "1" (S1 range) and "5" (S5 range) using the transmission control switch.

Shifting to "+" once raises the shift range by one, and shifting to "-" once lowers the shift range by one.

WIRING DIAGRAM

C179318E11
5.458,1.115 5.688,1.281 0.229,0.167 10 false 15 4.198,2.302 4.292,2.469 0.094,0.167 10 false 1 3.729,2.042 4.198,2.24 0.469,0.198 10 false SFTD 4.198,1.719 4.302,1.885 0.104,0.167 10 false 2 3.729,1.458 4.198,1.656 0.469,0.198 10 false SFTU 4.198,1.063 4.323,1.229 0.125,0.167 10 false 7 4,0.865 4.125,1.063 0.125,0.198 10 false S 2.667,1.115 2.771,1.281 0.104,0.167 10 false 3 2.844,0.875 3.083,1.073 0.24,0.198 10 false IG 2.667,2.302 2.792,2.469 0.125,0.167 10 false 5 2.844,2.042 3.083,2.24 0.24,0.198 10 false E 5.75,1 6.177,1.198 0.427,0.198 10 false S 5.458,1.708 5.688,1.875 0.229,0.167 10 false 22 5.75,1.594 6.177,1.792 0.427,0.198 10 false SFTU 5.458,2.292 5.688,2.458 0.229,0.167 10 false 23 5.75,2.156 6.177,2.354 0.427,0.198 10 false SFTD 2.573,2.792 4.354,2.99 1.781,0.198 10 false Transmission Control Switch 0.604,0.979 1.5,1.344 0.896,0.365 10 false from ECU-IG NO.1 Fuse 5.927,2.896 6.229,3.063 0.302,0.167 10 false G70 5.927,3.052 6.354,3.25 0.427,0.198 10 false TCM 2.573,2.615 2.875,2.813 0.302,0.198 10 false G47

PROCEDURE

1.INSPECT TRANSMISSION CONTROL SWITCH
a.
C203344E49
1.813,0.771 2.385,0.25 false 1.885,0.771 2.385,0.49 false 1.635,0.75 1.063,0.25 false 1.063,1.385 1.656,0.979 false 2.385,1.146 1.917,0.969 false 0.052,0 0.365,0.198 0.313,0.198 10 false *a 0.844,0.146 1.156,0.344 0.313,0.198 10 false IG 0.896,1.292 1.083,1.49 0.188,0.198 10 false S 2.427,0.146 2.854,0.344 0.427,0.198 10 false SFTU 2.427,0.375 2.854,0.573 0.427,0.198 10 false SFTD 2.427,1.063 2.854,1.26 0.427,0.198 10 false E

Disconnect the G47 transmission control switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (IG) - 7 (S) Shift lever in S, "+" or "-" Below 1 Ω
2 (SFTU) - 5 (E) Shift lever held in "+"
(Up-shift)
Below 1 Ω
1 (SFTD) - 5 (E) Shift lever held in "-"
(Down-shift)
Below 1 Ω
3 (IG) - 7 (S) Shift lever not in S, "+" or "-" 10 kΩ or higher
2 (SFTU) - 5 (E) Shift lever in S 10 kΩ or higher
1 (SFTD) - 5 (E) Shift lever in S 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Transmission Control Switch)



OK

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - BATTERY, BODY GROUND)

NG

REPLACE TRANSMISSION CONTROL SWITCH (TRANSMISSION FLOOR SHIFT ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - BATTERY, BODY GROUND)
a.
U169950E02
1.802,1.063 2.344,0.75 false 1.104,1.667 1.5,1.354 false 0.052,0 0.365,0.198 0.313,0.198 10 false *a 2.396,0.635 2.708,0.833 0.313,0.198 10 false IG 0.542,1 0.917,1.229 0.375,0.229 10 false G47 0.948,1.604 1.104,1.802 0.156,0.198 10 false E

Disconnect the G47 transmission control switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G47-3 (IG) - Body ground Ignition switch ON 11 to 14 V
G47-3 (IG) - Body ground Ignition switch off Below 1 V



c.

Turn the ignition switch off.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G47-5 (E) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Transmission Control Switch)


OK

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - TCM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - TCM)
a.
U169989E02
2.271,2.073 1.885,2.281 false 2.396,2.156 2.76,2.646 false 2.333,2.156 2,2.646 false 1.563,2.313 1.979,2.5 0.417,0.188 10 false 15 (S) 0.073,0.021 0.49,0.208 0.417,0.188 10 false *a 2.563,2.667 3.26,2.854 0.698,0.188 10 false 22 (SFTU) 1.656,2.667 2.354,2.854 0.698,0.188 10 false 23 (SFTD) 2.344,0.385 2.656,0.563 0.313,0.177 10 false G70

Disconnect the G70 TCM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G70-15 (S) - Body ground
·

Ignition switch ON

·

Shift lever in S, "+" or "-"


11 to 14 V
G70-15 (S) - Body ground
·

Ignition switch ON

·

Shift lever not in S, "+" or "-"


Below 1 V



c.

Turn the ignition switch off.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G70-22 (SFTU) - Body ground Shift lever held in "+"
(Up-shift)
Below 1 Ω
G70-23 (SFTD) - Body ground Shift lever held in "-"
(Down-shift)
Below 1 Ω
G70-22 (SFTU) - Body ground Shift lever in S 10 kΩ or higher
G70-23 (SFTD) - Body ground Shift lever in S 10 kΩ or higher



Text in Illustration
*a Rear view of wire harness connector
(to TCM)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR