Home › Drivetrain › A750F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM (for 1KD-FTV) › 2015.06–2017.08
RM27T0E _52 Drivetrain _053697 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0260766 AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV) J

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV)  Pattern Select Switch 2nd Start Mode Circuit  


DESCRIPTION

When 2nd start mode is selected with the pattern select (2ND) switch, the TCM controls the solenoid valves and the transmission starts from 2nd gear.

In 2nd start mode, the system operates the throttle motor to control engine output to reduce skidding of the drive wheels and guarantee stable acceleration from rest, straight driving and turning stability.

When the shift lever is in D, the transmission automatically shifts up from 2nd to 5th as usual.

HINT:
·

The pattern select (2ND) switch is a momentary-type switch.

·

In order to cancel 2nd start mode, push the pattern select (2ND) switch again or turn the ignition switch off.



WIRING DIAGRAM

C214971E06
2.513,2.456 3.949,2.833 1.436,0.378 10 Pattern Select (2ND) Switch Assembly 2.513,2.275 3.077,2.470 0.564,0.196 10 G159 2.546,1.588 2.938,1.784 0.392,0.196 10 E 3.527,1.588 3.919,1.784 0.392,0.196 10 2ND 3.939,1.793 4.331,1.989 0.392,0.196 10 4 5.809,2.904 6.310,3.100 0.502,0.196 10 G70 5.809,3.083 6.310,3.279 0.502,0.196 10 TCM 5.635,1.687 6.137,1.883 0.502,0.196 10 SNWI 5.325,1.793 5.561,1.989 0.236,0.196 10 13 2.371,1.793 2.763,1.989 0.392,0.196 10 1

PROCEDURE

1.INSPECT PATTERN SELECT (2ND) SWITCH ASSEMBLY
a.
C199167E04
0.056,0.004 0.215,0.206 0.159,0.202 10 *a 2.2,1.765 2.365,1.967 0.165,0.202 10 E 2.206,1.739 1.979,1.227 false 1.043,1.765 1.396,1.967 0.353,0.202 10 2ND 1.248,1.739 1.474,1.227 false

Remove the pattern select (2ND) switch assembly (See page Vehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 (E) - 4 (2ND) Pattern select (2ND) switch pushed Below 1 Ω
1 (E) - 4 (2ND) Pattern select (2ND) switch not pushed 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Pattern Select (2ND) Switch Assembly)



OK

2.CHECK HARNESS AND CONNECTOR (PATTERN SELECT (2ND) SWITCH - BODY GROUND)

NG

REPLACE PATTERN SELECT (2ND) SWITCH ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (PATTERN SELECT (2ND) SWITCH - BODY GROUND)
a.
U148261E04
1.24,1.792 1.469,1.281 false 0.052,0 0.24,0.198 0.188,0.198 10 false *a 0.458,1 0.938,1.188 0.479,0.188 10 false G159 1.135,1.813 1.292,2.01 0.156,0.198 10 false E

Disconnect the G159 pattern select (2ND) switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G159-1 (E) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Pattern Select (2ND) Switch Assembly)



OK

3.CHECK HARNESS AND CONNECTOR (PATTERN SELECT (2ND) SWITCH - TCM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (PATTERN SELECT (2ND) SWITCH - TCM)
a.
U169988E02
2.396,2.073 1.917,2.406 false 1.5,2.448 2.208,2.635 0.708,0.188 10 false 13 (SNWI) 0.083,0.042 0.292,0.229 0.208,0.188 10 false *a 2.323,0.375 2.635,0.552 0.313,0.177 10 false G70

Disconnect the G70 TCM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G70-13 (SNWI) - Body ground Pattern select (2ND) switch pushed Below 1 Ω
G70-13 (SNWI) - Body ground Pattern select (2ND) switch not pushed 10 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to TCM)



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR