Home › Drivetrain › CLUTCH › CLUTCH UNIT(for 1GD-FTV)
RM27T0E _52 Drivetrain _053699 CLUTCH _0260807 CLUTCH UNIT(for 1GD-FTV) G

CLUTCH  CLUTCH UNIT(for 1GD-FTV)  INSPECTION  


PROCEDURE

Hide 31250 1.INSPECT CLUTCH DISC ASSEMBLY

a.
C203262

Using a vernier caliper, measure the rivet head depth.

Minimum rivet head depth:

0.3 mm (0.0118 in.)


If the depth is less than the minimum, replace the clutch disc assembly.


b.
CL00373

Using a dial indicator, check the disc runout.

NOTICE:

Be sure to measure on the correct side of the clutch disc.


Maximum runout:

0.7 mm (0.0276 in.)


If the runout is more than the maximum, replace the clutch disc assembly.


Hide 31210 2.INSPECT CLUTCH COVER ASSEMBLY

a.
C215515E01
1.11,0.222 1.331,0.415 0.221,0.193 10 *a 0.615,0.918 0.836,1.111 0.221,0.193 10 *b

Using a vernier caliper, measure the depth and width of the worn areas of the diaphragm spring.

Maximum Wear:
Item Specified Condition
Width 6.0 mm (0.236 in.)
Depth 0.35 mm (0.0137 in.)


Text in Illustration
*a Width
*b Depth

If the depth or width is more than the maximum, replace the clutch cover assembly.


Hide 13405 3.INSPECT FLYWHEEL SUB-ASSEMBLY

a.
Q007250

Using a dial indicator, measure the flywheel runout.

Maximum runout:

0.1 mm (0.00393 in.)


If the runout is more than the maximum, replace the flywheel sub-assembly.


Hide 31230 4.INSPECT CLUTCH RELEASE BEARING ASSEMBLY

a.
N000414

Check that the bearing turns smoothly by hand by applying force in the axial direction.

If the bearing sticks or has a considerable amount of resistance, replace the release bearing.

HINT:

The bearing is permanently lubricated and requires no cleaning or lubrication.



Hide 36210A 5.INSPECT INPUT SHAFT FRONT BEARING

a.
Q002481

Check that the bearing turns smoothly by hand by applying rotational force.

If the bearing sticks or has a considerable amount of resistance, replace the input shaft front bearing.

HINT:

The bearing is permanently lubricated and requires no cleaning or lubrication.



Hide 36210A 6.REPLACE INPUT SHAFT FRONT BEARING

a.

Remove any 2 diametrically opposite bolts.


b.
Q007150E07
1.542,0.583 2,0.292 false 2.021,0.177 2.354,0.323 0.333,0.146 10 false SST

Using SST, remove the input shaft bearing.

SST
09303-35011  


c.
Q007151E09
1.406,0.135 1.219,0.135 false 1.219,0.135 1.219,0.844 false 1.448,0.031 1.771,0.198 0.323,0.167 10 false SST

Using SST and a hammer, tap in a new bearing.

SST
09304-12012  

HINT:

After installing the bearing to the hub, make sure that it rotates smoothly.



d.

Apply adhesive to 2 or 3 threads of the ends of each bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



e.

Install the 2 bolts.

Torque:
178 N*m (1815 kgf*cm, 131 ft.*lbf)