Home › Drivetrain › G52F (MANUAL TRANSMISSION / TRANSAXLE) › MANUAL TRANSMISSION UNIT
RM27T0E _52 Drivetrain _053700 G52F MANUAL TRANSMISSION / TRANSAXLE _0260813 MANUAL TRANSMISSION UNIT A

G52F MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSMISSION UNIT  DISASSEMBLY  


PROCEDURE

Hide 33101A 1.REMOVE MANUAL TRANSMISSION FILLER PLUG

a.
D029128

Remove the filler plug and gasket from the manual transmission case.


Hide 33104A 2.REMOVE DRAIN PLUG SUB-ASSEMBLY

a.
D029129

Remove the drain plug and gasket from the manual transmission case.


Hide 31204 3.REMOVE CLUTCH RELEASE FORK SUB-ASSEMBLY

Hide 31230 4.REMOVE CLUTCH RELEASE BEARING ASSEMBLY

Hide 31236B 5.REMOVE RELEASE FORK SUPPORT

a.
U169870

Remove the release fork support from the front transmission case.


Hide 31126 6.REMOVE CLUTCH RELEASE FORK BOOT

a.
D029348

Remove the clutch release fork boot from the front transmission case.


Hide 84210 7.REMOVE BACK-UP LIGHT SWITCH ASSEMBLY

a.
D029130E04
1.51,1.583 0.938,1.948 false 0.531,1.844 0.844,2.042 0.313,0.198 10 false SST

Using SST, remove the back-up light switch and gasket from the manual transmission case.

SST
09817-16011  


Hide 31111 8.REMOVE FRONT TRANSMISSION CASE

a.
U170551

Remove the 9 bolts.


b.
D029132

Using a plastic-faced hammer, tap off the front transmission case from the manual transmission case.


Hide 33280 9.REMOVE RESTRICT PIN

a.
C216025

Remove the 2 restrict pins from the transfer adapter.


Hide 33506F 10.REMOVE FLOOR SHIFT CONTROL SHIFT LEVER RETAINER SUB-ASSEMBLY

a.
C216026

Remove the 4 bolts from the transfer adapter.


b.

Remove the gasket from the adapter.


Hide 11.REMOVE SHIFT DETENT BALL

a.
D029138

Using a T40 "TORX" socket, remove the spring seat from the transfer adapter.


b.
D029139

Using a magnet hand, remove the compression spring and shift detent ball from the transfer adapter.


Hide 36117 12.REMOVE TRANSFER ADAPTER

a.
C216028

Remove the bolt from the shift lever housing.


b.
C145579

Remove the 8 bolts.


c.
D029137

Using a plastic-faced hammer, tap off the transfer adapter from the manual transmission case.


Hide 33449B 13.REMOVE TRANSMISSION MAGNET

a.
D029141

Remove the magnet from the transfer adapter.


Hide 33124E 14.REMOVE TRANSFER OIL RECEIVER PIPE

a.
D029142

Remove the receiver pipe from the transfer adapter.


Hide 33251 15.REMOVE SHIFT AND SELECT LEVER

a.
D029143E04
1.74,0.177 2.25,0.177 false 0.833,1.354 0.833,0.604 false 0.833,0.604 0.698,0.604 false 0.49,0.521 0.646,0.688 0.156,0.167 10 false *2 1.49,0.083 1.646,0.25 0.156,0.167 10 false *1

Remove the shift and select lever and shift lever housing from the transfer adapter.

Text in Illustration
*1 Shift Lever Housing
*2 Shift and Select Lever


Hide 33280 16.REMOVE REVERSE RESTRICT PIN ASSEMBLY

a.
D029144

Using a T40 "TORX" socket, remove the plug from the transfer adapter.


b.
D029145

Using a 5 mm pin punch and hammer, tap out the restrict slotted spring pin from the transfer adapter.


c.
D029146

Remove the restrict pin from the transfer adapter.


Hide 36117A 17.REMOVE TRANSFER ADAPTER OIL SEAL

a.
D029147

Using a screwdriver and hammer, tap out the oil seal from the transfer adapter.

NOTICE:

Be careful no to damage the surface which contacts the oil seal.



Hide 33131 18.REMOVE FRONT BEARING RETAINER

a.
U170552

Remove the 8 bolts.


b.

Remove the bearing retainer and gasket from the transmission case.


Hide 33131A 19.REMOVE TRANSMISSION FRONT BEARING RETAINER OIL SEAL

a.
D033559

Using a screwdriver, pry out the oil seal from the front bearing retainer.

NOTICE:

Be careful no to damage the surface which contacts the oil seal.



Hide 33311B 20.REMOVE FRONT BEARING SHAFT SNAP RING

a.
D029149

Using a snap ring expander, remove the snap ring from the input shaft front bearing.


Hide 33411D 21.REMOVE NO. 1 COUNTER GEAR FRONT BEARING SNAP RING

a.
D029150

Using a snap ring expander, remove the snap ring from the counter gear front bearing.


Hide 33111 22.REMOVE MANUAL TRANSMISSION CASE

a.
D033560

Stand the transmission as shown in the illustration.


b.

Using a plastic-faced hammer, carefully tap off the transmission case as shown in the illustration.


c.

Remove the transmission case from the intermediate plate.


Hide 23.FIX INTERMEDIATE PLATE

a.
D029152

Fix the intermediate plate in a vise between aluminum plates.


Hide 24.REMOVE SHIFT DETENT BALL

a.
D029153

Using a T40 "TORX" socket, remove the spring seat and 2 ball plugs from the intermediate plate.


b.
D029154

Using a magnet hand, remove the 3 compression springs and 3 shift detent balls from the intermediate plate.


Hide 33276B 25.REMOVE NO. 2 SHIFT DETENT BALL

a.
D029155

Using a T40 "TORX" socket, remove the spring seat from the intermediate plate.


b.
D029156

Using a magnet hand, remove the compression spring and No. 2 detent ball from the intermediate plate.


Hide 33245G 26.REMOVE NO. 4 GEAR SHIFT FORK SHAFT

a.
D029157

Remove the bolt from the No. 3 gear shift fork.


b.
C216029

Remove the shift detent ball from the reverse shift head.


c.
C216030

Remove the No. 4 gear shift fork shaft, shift detent ball and No. 3 gear shift fork from the intermediate plate.


Hide 33246C 27.REMOVE NO. 5 GEAR SHIFT FORK SHAFT

a.
D029160

Using a 5 mm pin punch and a hammer, tap out the slotted spring pin from the reverse shift head


b.
U170553

Remove the reverse shift head and No. 5 gear shift fork shaft from the intermediate plate.


Hide 33265 28.REMOVE NO. 2 SHIFT INTERLOCK PIN

a.
U170555

Using a magnet hand, remove the No. 2 shift interlock pin from the No. 3 gear shift fork shaft.


Hide 33244D 29.REMOVE NO. 3 GEAR SHIFT FORK SHAFT

a.
C216031

Using 2 screwdrivers and a hammer, remove the reverse shift head ring from the No. 3 shift fork shaft.


b.
C216032

Using a 5 mm pin punch and a hammer, tap out the slotted spring pin from the No. 3 shift fork shaft.


c.
C216033

Remove the No. 3 shift fork shaft from the intermediate plate.


Hide 33221 30.REMOVE REVERSE SHIFT ARM

a.
C216034

Remove the reverse shift arm from the reverse shift arm bracket.


b.
C216035

Using a screwdriver, remove the reverse shift arm E-ring.


c.

Remove the reverse shift fork from the reverse shift arm.


d.
C216036

Using a screwdriver, remove the shift arm shoe E-ring.


e.

Remove the shift arm shoe from the reverse shift arm.


Hide 33264 31.REMOVE NO. 3 SHIFT INTERLOCK PIN

a.

Using a magnet hand, remove the No. 3 shift interlock pin from the intermediate.


Hide 33265 32.REMOVE NO. 2 SHIFT INTERLOCK PIN

a.
D029168

Using a magnet hand, remove the No. 2 shift interlock pin from the No. 1 gear shift fork shaft.


Hide 33242 33.REMOVE NO. 1 GEAR SHIFT FORK SHAFT

a.
D029169

Using 2 screwdrivers and a hammer, remove the shaft snap ring from the No. 1 gearshift fork shaft.


b.
D029170

Remove the bolt from the No. 1 gear shift fork.


c.
C356972

Remove the No. 1 gear shift fork shaft from the intermediate plate.


Hide 33265 34.REMOVE NO. 1 SHIFT INTERLOCK PIN

a.
D029172

Using a magnet hand, remove the shift interlock pin from the intermediate plate.


Hide 33243A 35.REMOVE NO. 2 GEAR SHIFT FORK SHAFT

a.
D029173

Remove the bolt from the No. 2 gear shift fork.


b.
D029174

Using 2 screwdrivers and a hammer, remove the shaft snap ring from the No. 2 gear shift fork shaft.


c.
D029175

Remove the No. 2 gear shift fork shaft, No. 1 gear shift fork and No. 2 gear shift fork from the intermediate plate.


Hide 33428 36.INSPECT COUNTER SHAFT 5TH GEAR THRUST CLEARANCE

a.
C086399

Using a feeler gauge, measure the counter shaft 5th gear thrust clearance.

Standard clearance:

0.10 to 0.30 mm (0.00394 to 0.0118 in.)


If the result is not as specified, replace the counter shaft 5th gear.



Hide 33428 37.REMOVE COUNTER SHAFT 5TH GEAR

a.
C216038

Using 2 screwdrivers and a hammer, tap out the counter gear rear shaft snap ring from the counter gear.


b.
C216217E01
2.482,1.98 2.791,2.126 0.309,0.146 10 SST 2.181,1.416 2.294,2.057 false 2.294,2.057 2.424,2.057 false

Using SST, remove the No. 5 gear spline and the No. 1 synchronizer ring from the counter gear.

SST
09950-50013  (09951-05010, 09952-05010, 09953-05010, 09954-05021)


c.
D029178

Remove the counter shaft 5th gear and the counter 5th gear bearing from the counter gear.


Hide 33395 38.REMOVE NO. 3 TRANSMISSION HUB SLEEVE

a.
C216063E01
0.114,0.428 0.288,0.584 0.174,0.156 10 *1 0.758,0.347 0.932,0.503 0.174,0.156 10 *2 1.457,1.734 1.631,1.890 0.174,0.156 10 *3 1.54,0.107 1.714,0.263 0.174,0.156 10 *4 2.78,1.648 2.955,1.803 0.174,0.156 10 *5 0.343,0.508 0.537,0.508 false 0.537,0.508 0.537,0.869 false 1.513,0.791 1.513,0.434 false 1.513,0.434 0.973,0.434 false 1.231,0.835 1.231,0.434 false 1.82,1.238 1.82,1.826 false 1.82,1.826 1.66,1.826 false 2.064,0.385 2.064,0.193 false 2.064,0.193 1.775,0.193 false 2.866,1.318 2.866,1.597 false

Remove the No. 3 transmission hub sleeve, 2 synchromesh shifting key springs, 3 synchromesh shifting keys, counter 5th gear bearing and counter shaft 5th gear.

Text in Illustration
*1 No. 3 Transmission Hub Sleeve
*2 No. 3 Synchromesh Shifting Key Spring
*3 Counter 5th Gear Bearing
*4 No. 3 Synchromesh Shifting Key
*5 Counter Shaft 5th Gear


Hide 33349 39.REMOVE 5TH GEAR THRUST WASHER

a.
D029179

Remove the 5th gear thrust washer from the counter gear.


Hide 33359A 40.REMOVE 5TH GEAR BEARING INNER RACE LOCK BALL

a.
D029180

Using a magnet hand, remove the 5th gear bearing inner race lock ball from the counter gear.


Hide 33228 41.REMOVE REVERSE SHIFT ARM BRACKET

a.
C216039

Remove the 2 bolts and reverse shift arm bracket from the intermediate plate.


Hide 33402 42.REMOVE REVERSE IDLER GEAR SUB-ASSEMBLY

a.
C216040

Remove the bolt and reverse idler gear shaft stopper from the intermediate plate.


b.
C356973

Remove the reverse idler gear shaft and the reverse idler gear from the intermediate plate.


Hide 43.INSPECT REVERSE IDLER GEAR RADIAL CLEARANCE

a.
C086408

Using a dial indicator, measure the reverse idler gear radial clearance.

Standard clearance:

0.04 to 0.08 mm (0.00158 to 0.00314 in.)


Maximum clearance:

0.08 mm (0.00314 in.)


If the clearance is more than the maximum, replace the needle roller bearing.



Hide 33402 44.INSPECT REVERSE IDLER GEAR SUB-ASSEMBLY

a.
C086409

Using a feeler gauge, measure the clearance between the reverse idler gear and the shift arm shoe.

Standard clearance:

0.05 to 0.28 mm (0.00197 to 0.0110 in.)


Maximum clearance:

0.28 mm (0.00110 in.)


If the clearance is more than the maximum, replace the reverse idler gear and reverse shift arm.



Hide 33151 45.REMOVE OUTPUT SHAFT REAR BEARING RETAINER

a.
D029184

Using a T40 "TORX" socket wrench, remove the 4 screws and output shaft rear bearing retainer from the intermediate plate.


Hide 33421 46.REMOVE COUNTER GEAR ASSEMBLY

a.
D029185

Using a snap ring expander, remove the counter shaft center bearing snap ring from the counter shaft center bearing.


b.
C216218E01
2.86,1.858 3.155,2.005 0.295,0.147 10 SST 2.814,1.961 2.643,1.961 false 2.643,1.961 2.137,1.458 false

Using SST, remove the counter shaft center bearing and counter gear from the intermediate plate.

SST
09950-40011  (09951-04010, 09952-04010, 09953-04010, 09954-04010, 09955-04011, 09958-04011)


Hide 33311 47.REMOVE INPUT SHAFT ASSEMBLY

a.
C216043

Remove the input shaft with the 13 input shaft bearings and No. 2 synchronizer ring from the output shaft.


Hide 33321 48.REMOVE OUTPUT SHAFT ASSEMBLY

a.
D029187

Using a snap ring expander, remove the output shaft bearing shaft snap ring from the output shaft bearing.


b.
C216044

Remove the output shaft from the intermediate plate by pulling on the output shaft and tapping on the intermediate plate with a plastic-faced hammer.