Home › Drivetrain › G52F (MANUAL TRANSMISSION / TRANSAXLE) › OUTPUT SHAFT
RM27T0E _52 Drivetrain _053700 G52F MANUAL TRANSMISSION / TRANSAXLE _0260815 OUTPUT SHAFT A

G52F MANUAL TRANSMISSION / TRANSAXLE  OUTPUT SHAFT  DISASSEMBLY  


PROCEDURE

Hide 33336 1.INSPECT 5TH GEAR THRUST CLEARANCE

a.
C216059E01
2.14,1.042 2.14,0.395 false 2.14,0.395 2.309,0.395 false 2.352,0.308 2.503,0.467 0.151,0.159 10 *1

Using a dial indicator, measure the thrust clearance.

Standard clearance:

0.10 to 0.30 mm (0.00394 to 0.0118 in.)


Text in Illustration
*1 5th Gear

If the result is not as specified, replace the 5th gear.



Hide 33335 2.INSPECT 1ST GEAR THRUST CLEARANCE

a.
C216060E01
2.003,0.96 2.003,0.395 false 2.003,0.395 2.106,0.395 false 2.145,0.318 2.305,0.480 0.160,0.162 10 *1

Using a dial indicator, measure the thrust clearance.

Standard clearance:

0.10 to 0.25 mm (0.00394 to 0.00984 in.)


Text in Illustration
*1 1st Gear

If the result is not as specified, replace the No. 1 synchronizer ring set.



Hide 33332B 3.INSPECT 2ND GEAR THRUST CLEARANCE

a.
C216061E01
1.346,0.951 1.346,0.282 false 1.346,0.282 1.445,0.282 false 1.472,0.194 1.623,0.344 0.151,0.151 10 *1

Using a dial indicator, measure the thrust clearance.

Standard clearance:

0.10 to 0.25 mm (0.00394 to 0.00984 in.)


Text in Illustration
*1 2nd Gear

If the result is not as specified, replace the No. 1 synchronizer ring set.



Hide 33333 4.INSPECT 3RD GEAR THRUST CLEARANCE

a.
C086540E04
0.781,0.385 0.938,0.531 0.156,0.146 10 false *1

Using a feeler gauge, measure the thrust clearance.

Standard clearance:

0.10 to 0.25 mm (0.00394 to 0.00984 in.)


Text in Illustration
*1 3rd Gear

If the result is not as specified, replace the No. 2 synchronizer ring set.



Hide 33335 5.INSPECT 1ST GEAR RADIAL CLEARANCE

a.
C086541

Using a dial indicator, measure the radial clearance.

Standard clearance:

0.009 to 0.056 mm (0.000355 to 0.00220 in.)


If the result is not as specified, replace the 1st gear needle roller bearing.



Hide 33332 6.INSPECT 2ND GEAR RADIAL CLEARANCE

a.
C086542

Using a dial indicator, measure the radial clearance.

Standard clearance:

0.008 to 0.034 mm (0.000315 to 0.00133 in.)


If the result is not as specified, replace the 2nd gear needle roller bearing.



Hide 33333 7.INSPECT 3RD GEAR RADIAL CLEARANCE

a.
C086543

Using a dial indicator, measure the radial clearance.

Standard clearance:

0.008 to 0.034 mm (0.000315 to 0.00133 in.)


If the result is not as specified, replace the 3rd gear needle roller bearing.



Hide 33335 8.REMOVE 1ST GEAR

a.
D029212

Using 2 screwdrivers and a hammer, tap off the snap ring from the output shaft.


b.
D029213E02
2.531,0.99 2.375,0.99 2.375,0.99 2.167,1.667 false 2.583,0.917 2.948,1.115 0.365,0.198 10 false SST

Using SST and a press, remove the 5th gear, center bearing, 1st gear bearing inner race, 1st gear and 1st gear needle roller bearing from the output shaft.

SST
09527-10011  


Hide 33367 9.REMOVE NO. 1 SYNCHRONIZER RING (for 1st Gear)

a.

Remove the No. 1 synchronizer ring from the No. 1 clutch hub.


Hide 33355A 10.REMOVE 1ST GEAR BEARING INNER RACE LOCK BALL

a.
C086548

Using a magnet hand, remove the lock ball.


Hide 33332 11.REMOVE 2ND GEAR

a.
C216221E01
2.715,0.26 3.024,0.423 0.309,0.163 10 SST 2.665,0.351 2.354,0.351 false 2.354,0.351 2.185,0.838 false

Using SST and a press, remove the reverse gear, No. 1 transmission clutch hub, No. 1 synchronizer ring and 2nd gear.

SST
09950-00020  


Hide 33368 12.REMOVE NO. 2 SYNCHRONIZER RING (for 2nd Gear)

a.
C086550

Remove the No. 2 synchronizer ring from the 2nd gear.


Hide 33332B 13.REMOVE 2ND GEAR NEEDLE ROLLER BEARING

a.
C086551

Remove the needle roller bearing from the output shaft.


Hide 33361 14.REMOVE NO. 1 TRANSMISSION CLUTCH HUB

a.
C086552E03
0.323,1.115 0.323,0.094 false 0.323,0.094 0.469,0.094 false 2.896,1.26 2.896,1.604 false 1.052,0.885 1.052,0.271 false 1.052,0.271 1.177,0.271 false 1.667,1.479 1.667,1.792 false 1.667,1.792 1.823,1.792 false 2.052,0.698 2.052,0.26 false 2.052,0.26 2.198,0.26 false 0.521,0.031 0.792,0.229 0.271,0.198 10 false *1 2.823,1.625 3.021,1.823 0.198,0.198 10 false *2 1.229,0.198 1.448,0.385 0.219,0.188 10 false *3 1.896,1.719 2.125,1.885 0.229,0.167 10 false *4 2.25,0.188 2.458,0.375 0.208,0.188 10 false *1

Remove the 2 synchromesh shifting key springs.


b.

Remove the reverse gear and 3 synchromesh shifting keys from the transmission clutch hub.

Text in Illustration
*1 No. 1 Synchromesh Shifting Key Spring
*2 Reverse Gear
*3 No. 1 Synchromesh Shifting Key
*4 No. 1 Transmission Clutch Hub


Hide 33333 15.REMOVE 3RD GEAR

a.
C086553

Using a snap ring expander, remove the snap ring from the output shaft.


b.
C086554

Using a press, remove the No. 2 transmission clutch hub and 3rd gear.


Hide 33367 16.REMOVE NO. 1 SYNCHRONIZER RING

a.
C109888

Remove the No. 1 synchronizer ring from the 3rd gear.


Hide 33333A 17.REMOVE 3RD GEAR NEEDLE ROLLER BEARING

a.

Remove the needle roller bearing from the output shaft.


Hide 33362 18.REMOVE NO. 2 TRANSMISSION CLUTCH HUB

a.
C086557E03
0.542,0.177 0.344,0.177 false 0.344,0.177 0.344,1.104 false 0.781,1.292 0.781,0.479 false 0.781,0.479 0.948,0.479 false 1.729,1.49 1.729,1.896 false 2.25,0.198 2.052,0.198 false 2.052,0.198 2.052,0.698 false 2.771,1.302 2.771,1.688 false 0.563,0.094 0.719,0.24 0.156,0.146 10 false *1 2.688,1.74 2.844,1.885 0.156,0.146 10 false *2 0.979,0.385 1.135,0.531 0.156,0.146 10 false *3 1.625,1.927 1.781,2.073 0.156,0.146 10 false *4 2.281,0.115 2.438,0.26 0.156,0.146 10 false *1

Remove the 2 synchromesh shifting key springs.


b.

Remove the transmission hub sleeve and 3 synchromesh shifting keys from the transmission clutch hub.

Text in Illustration
*1 No. 2 Synchromesh Shifting Key Spring
*2 No. 2 Transmission Hub Sleeve
*3 No. 2 Synchromesh Shifting Key
*4 No. 2 Transmission Clutch Hub