Home › Drivetrain › RA61F (MANUAL TRANSMISSION / TRANSAXLE) › MANUAL TRANSMISSION UNIT(for 1GR-FE)
RM27T0E _52 Drivetrain _053701 RA61F MANUAL TRANSMISSION / TRANSAXLE _0260820 MANUAL TRANSMISSION UNIT(for 1GR-FE) A

RA61F MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSMISSION UNIT(for 1GR-FE)  DISASSEMBLY  


PROCEDURE

Hide 31204 1.REMOVE CLUTCH RELEASE FORK SUB-ASSEMBLY

Hide 33506F 2.REMOVE FLOOR SHIFT CONTROL SHIFT LEVER RETAINER SUB-ASSEMBLY

C215727

a.

Remove the 4 bolts.


b.

Using a plastic-faced hammer, remove the floor shift control shift lever retainer sub-assembly.


Hide 33521 3.REMOVE SHIFT LEVER HOUSING

C215730

a.

Remove the bolt and shift lever housing.


Hide 33121G 4.REMOVE MANUAL TRANSMISSION CASE COVER

F051569

a.

Remove the 4 bolts and manual transmission case cover.


Hide 33275F 5.REMOVE SHIFT DETENT BALL PLUG

F051570

a.

Using a 10 mm hexagon socket wrench, remove the shift detent ball plug from the transfer adapter.


b.

Remove the ball and compression spring from the transfer adapter.


Hide 33321G 6.REMOVE MANUAL TRANSMISSION OUTPUT SHAFT REAR SET NUT

a.

Using a belt and wooden block, securely fasten the manual transmission to the workbench.


b.
C215728

Using a chisel and hammer, unstake the manual transmission output shaft rear set nut.


c.
C199426E05
0.542,0.938 0.656,0.938 0.656,0.938 0.927,1.323 false 0.469,3.104 0.583,3.104 0.583,3.104 0.906,3.573 true 3,3.073 2.885,3.073 2.885,3.073 1.677,2.083 true 1.854,4.292 1.792,4.292 1.792,4.292 1.615,4.104 false 2.958,1.26 2.396,1.26 2.396,1.26 1.74,1.917 true 2.063,3.479 1.896,3.479 false 1.896,3.479 1.896,3.781 false 0.188,0.854 0.5,1 0.313,0.146 10 false SST 0.115,3.021 0.427,3.167 0.313,0.146 10 false SST 3.021,2.969 3.156,3.125 0.135,0.156 10 false A 1.875,4.198 2.01,4.354 0.135,0.156 10 false A 3,1.208 3.177,1.354 0.177,0.146 10 false *1 2.094,3.406 2.271,3.552 0.177,0.146 10 false *1

Engage 5th gear, and then secure the input shaft using SST.

SST
09322-35010  (09322-03010, 09322-03020, 09322-03030, 90105-12087, 90170-12030)

Text in Illustration
*1 Input Shaft

HINT:
·

Install SST securely so that the part labeled A is in-line with the input shaft.

·

Make sure that the part labeled A moves back and forth by hand after installing SST.




d.
C199433E02
1.146,0.135 1.292,0.135 1.292,0.135 2.042,0.677 true 0.792,0.052 1.104,0.208 0.313,0.156 10 false SST

Using an L-type handle and SST, remove the manual transmission output shaft rear set nut from the output shaft.

SST
09326-35010  (09326-03010)


e.

Remove the belt and wooden block from the manual transmission.


f.
C215729E01
2.647,1.885 2.800,2.037 0.152,0.152 10 *1 2.226,1.54 2.379,1.693 0.152,0.152 10 *2 2.317,1.276 2.317,1.506 false 2.731,1.615 2.731,1.867 false

Remove the rear output shaft bearing (inner race) and output shaft spacer.

Text in Illustration
*1 Rear Output Shaft Bearing
*2 Output Shaft Spacer


Hide 36117 7.REMOVE TRANSFER ADAPTER

C217228E02
0.719,0.469 0.719,0.135 false 0.719,0.135 0.563,0.135 false 2.719,0.479 2.719,0.146 false 2.719,0.146 2.563,0.146 false 3.208,1.365 2.844,1.365 true 0.385,1.583 0.385,1.802 true 0.354,0.063 0.51,0.208 0.156,0.146 10 false *1 2.354,0.073 2.51,0.219 0.156,0.146 10 false *1 3.229,1.281 3.385,1.427 0.156,0.146 10 false *1 0.313,1.823 0.469,1.969 0.156,0.146 10 false *1

a.

Remove the 10 bolts and 4 brackets.

Text in Illustration
*1 Bracket


b.
D033739

Using a plastic-faced hammer, carefully tap off the transfer adapter to remove it.

HINT:

Place a brass bar against the rib portion of the transfer adapter.



Hide 33101A 8.REMOVE MANUAL TRANSMISSION FILLER PLUG

F051572

a.

Remove the 2 manual transmission filler plugs and 2 gaskets from the transfer adapter.


Hide 33124C 9.REMOVE NO. 1 OIL RECEIVER PIPE

F051573

a.

Remove the No. 1 oil receiver pipe from the transfer adapter.


Hide 36867B 10.REMOVE OIL SEPARATOR PACKING SEAL

F051828

a.

Remove the oil separator packing seal from the transfer adapter.


Hide 36117G 11.REMOVE TRANSFER ADAPTER CASE PLUG

a.
C215734

Using a 14 mm hexagon socket wrench, remove the transfer adapter case plug from the transfer adapter.


Hide 33321A 12.REMOVE REAR OUTPUT SHAFT BEARING

C217357E01
0.125,0.989 0.416,1.131 0.291,0.142 10 SST 1.697,0.976 1.988,1.118 0.291,0.142 10 SST 0.49,1.081 0.683,1.081 false 0.683,1.081 0.914,1.358 false 2.413,1.343 2.187,1.06 false 2.187,1.06 2.069,1.06 false

a.

Using SST, remove the 2 rear output shaft bearings (outer race) from the transfer adapter.

SST
09308-00010  


Hide 33421G 13.REMOVE COUNTER GEAR REAR RADIAL BALL BEARING

D033746

a.

Remove the bolt and bearing lock plate.


b.
C216330E01
0.11,0.346 0.403,0.499 0.293,0.154 10 SST 0.511,0.443 0.904,0.443 false

Using SST, remove the counter gear rear radial ball bearing from the transfer adapter.

SST
09308-00010  


Hide 36117Q 14.REMOVE TRANSFER ADAPTER NEEDLE ROLLER BEARING

a.

Remove the transfer adapter needle roller bearing from the transfer adapter.


Hide 33176B 15.REMOVE TRANSMISSION OIL SEPARATOR

F051575

a.

Remove the 2 bolts and transmission oil separator.


Hide 33451H 16.REMOVE REVERSE IDLER GEAR SHAFT BOLT

D033649

a.

Remove the reverse idler gear shaft bolt and gasket from the reverse idler gear shaft.


Hide 33101 17.REMOVE TRANSMISSION MIDDLE CASE

a.
C215733E02
1.177,1.448 1.354,1.448 1.354,1.448 1.615,1.198 true 2.521,0.469 2.302,0.469 2.302,0.469 2,0.927 true 0.969,1.344 1.146,1.5 0.177,0.156 10 true *1 2.552,0.385 2.729,0.552 0.177,0.167 10 true *2

Remove the bolt and collar.

Text in Illustration
*1 Bolt
*2 Collar


b.
C217230

Remove the 11 bolts.


c.
D033741

Using a plastic-faced hammer, carefully tap off the transmission middle case to remove it.

HINT:

Place a brass bar against the rib portion of the transmission middle case.



Hide 33104 18.REMOVE DRAIN PLUG SUB-ASSEMBLY

F051576

a.

Remove the drain plug sub-assembly and gasket from the transmission middle case.


Hide 33124D 19.REMOVE NO. 2 OIL RECEIVER PIPE

F051577

a.

Remove the No. 2 oil receiver pipe from the transmission middle case.


Hide 33261C 20.REMOVE SHIFT AND SELECT LEVER SHAFT

C215737

a.

Remove the shift and select lever shaft from the reverse gear shaft.


Hide 33251 21.REMOVE SHIFT AND SELECT LEVER

a.
C215739

Using a screwdriver, remove the E-ring.


b.
C215740

Using a 5 mm pin punch and hammer, tap out the slotted pin.


c.
C215738

Remove the bolt, shift and select lever, shift and select cam and shift interlock plate from the lever shaft


d.

Remove the lock ball pin and compression spring from the shift and select lever.


Hide 84210 22.REMOVE BACK-UP LIGHT SWITCH ASSEMBLY

F051581E04
1.698,1.76 1.698,1.51 false 1.563,1.781 1.854,1.958 0.292,0.177 10 false SST

a.

Using SST, remove the back-up light switch assembly and gasket.

SST
09817-16011  


Hide 33461 23.INSPECT REVERSE IDLER GEAR THRUST CLEARANCE

a.
D033776

Using a feeler gauge, measure the thrust clearance.

Standard clearance:

0.13 to 0.154 mm (0.00512 to 0.00606 in.)


Maximum clearance:

0.154 mm (0.00606 in.)


If the clearance is more than the maximum, replace the reverse idler gear shaft, reverse idler gear or front transmission case.



Hide 33461 24.REMOVE REVERSE IDLER GEAR

D033634

a.

Remove the reverse idler gear shaft, reverse idler gear bearing and reverse idler gear.


Hide 33111 25.REMOVE FRONT TRANSMISSION CASE

a.
F051582

Remove the 4 bolts from the shift interlock bracket.


b.
F051583

Using a 27 mm hexagon wrench, remove the manual transmission case plug.


c.
D033636

Tie the input shaft assembly, counter gear assembly and control assembly with a piece of rope or string.


d.
D033637

Expand the 2 front bearing shaft snap rings and lift up the output shaft assembly, input shaft assembly, counter gear assembly, shift interlock bracket, gear shift forks and gear shift fork shafts.


e.
D033638

Remove the output shaft assembly, input shaft assembly, counter gear assembly shift interlock bracket, gear shift forks and gear shift fork shafts while gently tapping the clutch housing with a plastic-faced hammer.

NOTICE:

Take care not to subject the output shaft assembly, input shaft assembly, counter gear assembly, shift interlock bracket, gear shift forks and gear shift fork shafts to any impact. This could cause the ball and spring to come out.



f.

Separate the output shaft assembly, input shaft assembly, counter gear assembly and gear shift forks.


Hide 33124L 26.REMOVE NO. 3 OIL RECEIVER PIPE

F051585

a.

Remove the No. 3 oil receiver pipe from the front transmission case.


Hide 33311G 27.REMOVE FRONT BEARING SHAFT SNAP RING

D033639

a.

Using snap ring pliers, remove the 2 front bearing shaft snap rings.


Hide 33111Q 28.REMOVE TRANSMISSION CASE OIL SEAL

C216331E01
0.331,0.508 0.636,0.655 0.306,0.147 10 SST 1.351,0.6 0.713,0.6 false

a.

Using SST, remove the transmission case oil seal from the front transmission case.

SST
09308-00010  


Hide 33112H 29.REMOVE TRANSMISSION CASE NEEDLE BEARING

a.

Using SST, remove the transmission case needle bearing from the front transmission case.

SST
09319-60020  

C335234C01
5.5,2.563 5.365,2.792 5.365,2.792 5.365,2.927 true 3.844,1.458 4.51,1.656 4.51,1.656 4.635,1.656 false 2.333,0.844 2.521,1.031 0.188,0.188 10 false *a 5.271,2.958 5.458,3.146 0.188,0.188 10 true *1 4.667,1.583 4.99,1.74 0.323,0.156 10 false SST

Text in Illustration
*1 Transmission Case Needle Bearing - -
*a Hold - -
V113147

Turn - -


Hide 33214G 30.REMOVE NO. 3 GEAR SHIFT FORK

F051588

a.

Remove the bolt and No. 3 gear shift fork.


Hide 33244D 31.REMOVE NO. 3 GEAR SHIFT FORK SHAFT

C232591

a.

Remove the No. 3 gear shift fork shaft, shift detent ball and compression spring.


Hide 33213G 32.REMOVE NO. 2 GEAR SHIFT FORK

C388675

a.

Remove the bolt and No. 2 gear shift fork.


Hide 33243A 33.REMOVE NO. 2 GEAR SHIFT FORK SHAFT

C232592

a.

Remove the No. 2 gear shift fork shaft, shift detent ball and compression spring.


Hide 33242 34.REMOVE NO. 1 GEAR SHIFT FORK SHAFT

a.
D033718

Using a 5 mm pin punch and hammer, tap out the slotted spring pin from the No. 1 gear shift head.


b.
C232593

Remove the No. 1 gear shift fork shaft, shift detent ball, compression spring and No. 1 gear shift head.


Hide 33212A 35.REMOVE NO. 1 GEAR SHIFT FORK

a.
D033720

Using a 5 mm pin punch and hammer, tap out the slotted spring pin.


b.
D033721

Remove the No. 2 gear shift head and No. 1 gear shift fork.


Hide 33215B 36.REMOVE NO. 4 GEAR SHIFT FORK

D033722

a.

Using a 5 mm pin punch and hammer, tap out the slotted spring pin.


b.

Remove the No. 4 gear shift fork.


Hide 33245G 37.REMOVE NO. 4 GEAR SHIFT FORK SHAFT

D033723

a.

Remove the No. 4 gear shift fork shaft, shift detent ball and compression spring.


Hide 33229A 38.REMOVE NO. 1 RELEASE ARM

D033724

a.

Using a screwdriver, remove the E-ring.


b.
U170558

Remove the shift arm pivot and No. 1 release arm.