Home › Drivetrain › RA61F (MANUAL TRANSMISSION / TRANSAXLE) › INPUT SHAFT
RM27T0E _52 Drivetrain _053701 RA61F MANUAL TRANSMISSION / TRANSAXLE _0260821 INPUT SHAFT A

RA61F MANUAL TRANSMISSION / TRANSAXLE  INPUT SHAFT  DISASSEMBLY  


PROCEDURE

Hide 33337 1.INSPECT 6TH GEAR THRUST CLEARANCE

F051109

a.

Using a dial indicator, measure the 6th gear thrust clearance.

Standard clearance:

0.20 to 0.49 mm (0.00788 to 0.0193 in.)


If the clearance is outside the specification, replace the gear, spacer or shaft.

HINT:

Replace the part or parts determined to be the most likely cause of the problem.



Hide 33333 2.INSPECT 3RD GEAR THRUST CLEARANCE

F051110

a.

Using a feeler gauge, measure the 3rd gear thrust clearance.

Standard clearance:

0.09 to 0.52 mm (0.00355 to 0.0205 in.)


If the clearance is outside the specification, replace the gear, thrust washer, clutch hub or shaft.

HINT:

Replace the part or parts determined to be the most likely cause of the problem.



Hide 33334 3.INSPECT 4TH GEAR THRUST CLEARANCE

F051111

a.

Using a dial indicator, measure the 4th gear thrust clearance.

Standard clearance:

0.12 to 0.38 mm (0.00473 to 0.0150 in.)


If the clearance is outside the specification, replace the gear, clutch hub or shaft.

HINT:

Replace the part or parts determined to be the most likely cause of the problem.



Hide 33337 4.INSPECT 6TH GEAR RADIAL CLEARANCE

F051106

a.

Using a dial indicator, measure the 6th gear radial clearance.

Standard clearance:

0.015 to 0.065 mm (0.000591 to 0.00255 in.)


If the clearance is outside the specification, replace the gear, needle roller bearing or shaft.

HINT:

Replace the part or parts determined to be the most likely cause of the problem.



Hide 33333 5.INSPECT 3RD GEAR RADIAL CLEARANCE

F051107

a.

Using a dial indicator, measure the 3rd gear radial clearance.

Standard clearance:

0.015 to 0.067 mm (0.000591 to 0.00263 in.)


If the clearance is outside the specification, replace the gear, needle roller bearing or shaft.

HINT:

Replace the part or parts determined to be the most likely cause of the problem.



Hide 33334 6.INSPECT 4TH GEAR RADIAL CLEARANCE

F051108

a.

Using a dial indicator, measure the 4th gear radial clearance.

Standard clearance:

0.015 to 0.051 mm (0.000591 to 0.00200 in.)


If the clearance is outside the specification, replace the gear, needle roller bearing or shaft.

HINT:

Replace the part or parts determined to be the most likely cause of the problem.



Hide 33393A 7.REMOVE NO. 3 TRANSMISSION CLUTCH HUB SHAFT SNAP RING

D033652

a.

Using 2 screwdrivers and a hammer, tap off the snap ring.

HINT:

Use a piece of cloth to prevent the snap ring from flying off.



Hide 33337 8.REMOVE 6TH GEAR SUB-ASSEMBLY

C216335E01
0.902,2.059 1.207,2.204 0.304,0.145 10 SST 1.298,2.136 1.7,2.136 false 1.653,2.286 1.487,2.286 false 1.487,2.286 1.487,2.136 false 0.272,0.272 0.576,0.417 0.304,0.145 10 SST 0.639,0.374 0.914,0.374 false 0.914,0.374 1.068,0.78 false

a.

Using SST and a press, remove the No. 3 transmission clutch hub, hub sleeve, synchronizer ring and 6th gear from the input shaft.

SST
09950-00020  
09950-70010  (09951-07200)
09950-60010  (09951-00300)

NOTICE:
·

Do not tighten SST excessively.

·

Support the input shaft by hand so that it does not fall.




Hide 33337A 9.REMOVE 6TH GEAR NEEDLE ROLLER BEARING

a.

Remove the 6th gear needle roller bearing from the input shaft.


Hide 33311F 10.REMOVE SPACER

a.

Remove the spacer from the input shaft.


Hide 33342B 11.REMOVE GEAR THRUST WASHER SHAFT SNAP RING

D033654

a.

Using a snap ring expander, remove the snap ring from the input shaft.


Hide 33342C 12.REMOVE 3RD GEAR THRUST WASHER

a.

Remove the 3rd gear thrust washer from the input shaft.


Hide 33333 13.REMOVE 3RD GEAR

a.

Remove the 3rd gear from the input shaft.


Hide 14.REMOVE STRAIGHT PIN

a.

Remove the straight pin from the input shaft.


Hide 33333A 15.REMOVE 3RD GEAR NEEDLE ROLLER BEARING

a.

Remove the 3rd gear needle roller bearing from the input shaft.


Hide 16.REMOVE SPACER

a.

Remove the spacer from the input shaft.


Hide 33038E 17.REMOVE NO. 2 SYNCHRONIZER RING SET

a.
F051095

Remove the No. 2 synchronizer ring set from the input shaft.


Hide 33362A 18.REMOVE NO. 2 CLUTCH HUB SETTING SHAFT SNAP RING

D033657

a.

Using a snap ring expander, remove the snap ring from the input shaft.


Hide 33334 19.REMOVE 4TH GEAR

C216336E01
1.675,0.144 0.888,0.144 false 1.632,0.243 1.263,0.243 false 1.263,0.243 1.263,0.144 false 0.504,0.076 0.817,0.215 0.313,0.138 10 SST 1.931,1.987 2.244,2.125 0.313,0.138 10 SST 2.319,2.069 2.453,2.069 false 2.453,2.069 2.453,2.826 false

a.

Using SST and a press, remove the No. 2 transmission clutch hub, hub sleeve, synchronizer ring and 4th gear from the input shaft.

SST
09950-00020  
09950-60010  (09951-00300)
09950-70010  (09951-07200)

NOTICE:

Support the input shaft by hand so that it does not fall.



Hide 33334A 20.REMOVE 4TH GEAR NEEDLE ROLLER BEARING

a.

Remove the 4th gear needle roller bearing from the input shaft.


Hide 33311P 21.REMOVE INPUT SHAFT FRONT BEARING SNAP RING

D033659

a.

Using 2 screwdrivers and a hammer, tap off the snap ring.

HINT:

Use a piece of cloth to prevent the snap ring from flying off.



Hide 33311A 22.REMOVE INPUT SHAFT FRONT BEARING

C216337E01
0.435,0.765 0.739,0.914 0.304,0.149 10 SST 0.838,0.847 1.083,0.847 false 1.083,0.847 1.363,1.275 false

a.

Using SST and a press, remove the input shaft front bearing from the input shaft.

SST
09950-00020  

NOTICE:

Support the input shaft by hand so that it does not fall.



Hide 33362 23.REMOVE NO. 2 TRANSMISSION CLUTCH HUB

C136406E02
0.703,1.019 0.825,1.019 0.825,1.019 1.114,1.586 false 0.58,1.466 0.702,1.466 0.702,1.466 1.091,1.705 false 1.654,1.452 1.532,1.452 1.532,1.452 1.18,1.8 false 0.466,0.918 0.630,1.076 0.164,0.158 10 *1 0.369,1.379 0.532,1.538 0.164,0.158 10 *2 1.749,1.373 1.912,1.531 0.164,0.158 10 *3

a.

Remove the clutch hub, 3 synchromesh shifting keys, 3 balls and 3 springs from the hub sleeve.

Text in Illustration
*1 Spring
*2 Ball
*3 Synchronizer Shifting Key

HINT:

Use a piece of cloth to prevent the balls and springs from flying off.



Hide 33393 24.REMOVE NO. 3 TRANSMISSION CLUTCH HUB

HINT:

Perform the same procedure as for the No. 2 clutch hub.