Home › Drivetrain › RA61F (MANUAL TRANSMISSION / TRANSAXLE) › COUNTER GEAR
RM27T0E _52 Drivetrain _053701 RA61F MANUAL TRANSMISSION / TRANSAXLE _0260826 COUNTER GEAR G

RA61F MANUAL TRANSMISSION / TRANSAXLE  COUNTER GEAR  INSPECTION  


PROCEDURE

Hide 33421 1.INSPECT COUNTER GEAR

F051553

a.

Using a dial indicator and 2 V-blocks, measure the shaft runout.

Maximum runout:

0.03 mm (0.00118 in.)


If the runout is more than the maximum, replace the counter gear.


b.
C354118E01
3,4.083 3,3.792 false 1.333,4.083 1.333,3.844 false 0.917,4.083 0.917,3.844 false 0.542,4.083 0.542,3.792 false 0.333,4.083 0.333,3.76 false 0.292,4.125 0.458,4.292 0.167,0.167 10 false A 0.51,4.125 0.677,4.292 0.167,0.167 10 false B 1.292,4.115 1.458,4.281 0.167,0.167 10 false D 2.958,4.125 3.125,4.292 0.167,0.167 10 false E 0.875,4.125 1.042,4.292 0.167,0.167 10 false C

Using a micrometer, measure the journal diameter of each input shaft journal, at the specified positions.

Standard Journal Diameter:
Item Specified Condition
Journal A 34.002 to 34.015 mm (1.3387 to 1.3392 in.)
Journal B 36.985 to 37.000 mm (1.4561 to 1.4567 in.)
Journal C 47.985 to 48.000 mm (1.8892 to 1.8898 in.)
Journal D 53.985 to 54.000 mm (2.1254 to 2.1260 in.)
Journal E 34.002 to 34.015 mm (1.3387 to 1.3392 in.)


Minimum Journal Diameter:
Item Specified Condition
Journal A 34.002 mm (1.3387 in.)
Journal B 36.985 mm (1.4561 in.)
Journal C 47.985 mm (1.8892 in.)
Journal D 53.985 mm (2.1254 in.)
Journal E 34.002 mm (1.3387 in.)


If the journal diameter is less than the minimum, replace the counter gear shaft.


Hide 33425 2.INSPECT COUNTER SHAFT REVERSE GEAR

F051555

a.

Using a cylinder gauge, measure the inside diameter of the reverse gear.

Standard inside diameter:

51.015 to 51.040 mm (2.0085 to 2.0095 in.)


Maximum inside diameter:

51.040 mm (2.0095 in.)


If the inside diameter is more than the maximum, replace the reverse gear.


Hide 33426A 3.INSPECT COUNTER SHAFT 1ST SPEED GEAR

F051556

a.

Using a cylinder gauge, measure the inside diameter of the 1st gear.

Standard inside diameter:

54.015 to 54.040 mm (2.1266 to 2.1276 in.)


Maximum inside diameter:

54.040 mm (2.1276 in.)


If the inside diameter is more than the maximum, replace the 1st gear.


Hide 33424 4.INSPECT COUNTER SHAFT 2ND SPEED GEAR

F051557

a.

Using a cylinder gauge, measure the inside diameter of the 2nd gear.

Standard inside diameter:

60.015 to 60.040 mm (2.3628 to 2.3638 in.)


Maximum inside diameter:

60.040 mm (2.3638 in.)


If the inside diameter is more than the maximum, replace the 2nd gear.


Hide 33395 5.INSPECT NO. 3 TRANSMISSION HUB SLEEVE

C354119E01
1.958,0.24 2.219,0.438 0.26,0.198 10 false A 1.771,4.323 2.031,4.521 0.26,0.198 10 false B

a.

Using a vernier caliper, measure the width of the No. 3 transmission hub sleeve groove (A) and the thickness of the claw part of the gear shift fork No. 4 (B), and calculate the clearance.

Standard clearance (A - B):

0.26 to 0.84 mm (0.0102 to 0.0331 in.)


If the clearance is outside the specification, replace the No. 3 transmission hub sleeve and No. 4 gear shift fork.


Hide 33363 6.INSPECT NO. 1 TRANSMISSION HUB SLEEVE

C067843

a.

Check the sliding condition between the No. 1 transmission hub and No. 1 transmission hub sleeve.


b.

Check that the splines of the No. 1 transmission hub sleeve are not worn.


c.
C354120E01
2.042,0.281 2.271,0.531 0.229,0.25 10 false A 1.802,4.292 2.031,4.542 0.229,0.25 10 false B

Using a vernier caliper, measure the width of the No. 1 transmission hub sleeve groove (A) and the thickness of the claw part of the No. 1 gear shift fork (B), and calculate the clearance.

Standard clearance (A - B):

0.15 to 0.35 mm (0.00591 to 0.0138 in.)


If the clearance is outside the specification, replace the No. 1 transmission hub sleeve and No. 1 gear shift fork.


Hide 33369B 7.INSPECT NO. 4 SYNCHRONIZER RING

F051636

a.

Using a feeler gauge, measure the clearance between the synchronizer ring and reverse gear.

Standard clearance:

0.70 to 1.50 mm (0.0276 to 0.0590 in.)


Minimum clearance:

0.70 mm (0.0276 in.)


If the clearance is less than the minimum, replace the synchronizer ring.


b.

Coat the reverse gear cone with gear oil.


c.
D033665

Check the braking effect of the synchronizer ring.

i.

Turn the synchronizer ring in both directions while pushing it against the reverse gear cone. Check that the ring locks in both directions.

If No. 4 synchronizer ring turns, replace it.




Hide 33037B 8.INSPECT NO. 1 SYNCHRONIZER RING SET (for 1st Gear)

F051638E06
2.344,1.177 2,1.427 true 2.635,1.115 2.927,0.552 true 2.427,0.99 2.771,0.177 true 2.813,0.083 3,0.26 0.188,0.177 10 false *1 2.979,0.448 3.167,0.625 0.188,0.177 10 false *2 1.729,1.354 1.917,1.531 0.188,0.177 10 false *3

a.

Using a feeler gauge, measure the clearance between the synchronizer ring and 1st gear.

Standard clearance:
Inner:

1.48 to 2.12 mm (0.0583 to 0.0835 in.)

Middle:

0.68 to 1.92 mm (0.0268 to 0.0756 in.)

Outer:

0.88 to 1.72 mm (0.0346 to 0.0677 in.)


Minimum clearance:
Inner:

1.48 mm (0.0583 in.)

Middle:

0.68 mm (0.0268 in.)

Outer:

0.88 mm (0.0346 in.)


Text in Illustration
*1 Middle
*2 Outer
*3 Inner

If the clearance is less than the minimum, replace the synchronizer ring.


b.

Coat the 1st gear cone with gear oil.


c.
F051639

Check the braking effect of the synchronizer ring.

i.

Turn the synchronizer ring in both directions while pushing it against the 1st gear cone. Check that the ring locks in both directions.

If No. 1 synchronizer ring set turns, replace it.




Hide 33037B 9.INSPECT NO. 1 SYNCHRONIZER RING SET (for 2nd Gear)

F051638E06
2.344,1.177 2,1.427 true 2.635,1.115 2.927,0.552 true 2.427,0.99 2.771,0.177 true 2.813,0.083 3,0.26 0.188,0.177 10 false *1 2.979,0.448 3.167,0.625 0.188,0.177 10 false *2 1.729,1.354 1.917,1.531 0.188,0.177 10 false *3

a.

Using a feeler gauge, measure the clearance between the synchronizer ring and 2nd gear.

Standard clearance:
Inner:

1.48 to 2.12 mm (0.0583 to 0.0835 in.)

Middle:

0.68 to 1.92 mm (0.0268 to 0.0756 in.)

Outer:

0.88 to 1.72 mm (0.0346 to 0.0677 in.)


Minimum clearance:
Inner:

1.48 mm (0.0583 in.)

Middle:

0.68 mm (0.0268 in.)

Outer:

0.88 mm (0.0346 in.)


Text in Illustration
*1 Middle
*2 Outer
*3 Inner

If the clearance is less than the minimum, replace the synchronizer ring.


b.

Coat the 2nd gear cone with gear oil.


c.
F051639

Check the braking effect of the synchronizer ring.

i.

Turn the synchronizer ring in both directions while pushing it against the 2nd gear cone. Check that the ring locks in both directions.

If No. 1 synchronizer ring set turns, replace it.