Home › Drivetrain › R150F (MANUAL TRANSMISSION / TRANSAXLE) › OUTPUT SHAFT
RM27T0E _52 Drivetrain _053702 R150F MANUAL TRANSMISSION / TRANSAXLE _0260833 OUTPUT SHAFT G

R150F MANUAL TRANSMISSION / TRANSAXLE  OUTPUT SHAFT  INSPECTION  


PROCEDURE

Hide 33321 1.INSPECT OUTPUT SHAFT

a.
D029121

Using a dial indicator, measure the output shaft runout.

Maximum runout:

0.03 mm (0.00118 in.)


If the runout is more than the maximum, replace the output shaft with a new one.



b.
C357736E01
1.698,3.125 1.854,3.323 0.156,0.198 10 false A 2.26,3.094 2.417,3.292 0.156,0.198 10 false B 2.573,3.104 2.729,3.302 0.156,0.198 10 false C

Using a micrometer, measure the journal diameter at A, B and C on the output shaft.

Standard Journal Diameter:
Item Specified Condition
Journal A 38.979 to 38.995 mm (1.5346 to 1.5352 in.)
Journal B 46.984 to 47.000 mm (1.8498 to 1.8504 in.)
Journal C 37.984 to 38.000 mm (1.4954 to 1.4961 in.)


If the diameter is not as specified, replace the output shaft with a new one.



c.
D026065

Using a micrometer, measure the thickness of the output shaft flange as shown in the illustration.

Standard thickness:

4.8 to 5.2 mm (0.189 to 0.204 in.)


If the thickness is not as specified, replace the output shaft.



Hide 33333 2.INSPECT 3RD GEAR

a.
D026066

Using a cylinder gauge, measure the inside diameter of the 3rd gear.

Standard inside diameter:

44.015 to 44.040 mm (1.7329 to 1.7339 in.)


Maximum inside diameter:

44.040 mm (1.7339 in.)


If the inside diameter is more than the maximum, replace the 3rd gear with a new one.



Hide 33332 3.INSPECT 2ND GEAR

a.
D026067

Using a cylinder gauge, measure the inside diameter of the 2nd gear.

Standard inside diameter:

53.015 to 53.040 mm (2.0872 to 2.0881 in.)


Maximum inside diameter:

53.040 mm (2.0881 in.)


If the inside diameter is more than the maximum, replace the 2nd gear with a new one.



Hide 33335 4.INSPECT 1ST GEAR

a.
D026068

Using a cylinder gauge, measure the inside diameter of the 1st gear.

Standard inside diameter:

46.015 to 46.040 mm (1.812 to 1.8126 in.)


Maximum inside diameter:

46.040 mm (1.8126 in.)


If the inside diameter is more than the maximum, replace the 1st gear with a new one.



Hide 33348 5.INSPECT 1ST GEAR THRUST WASHER

a.
D026069

Using a micrometer, measure the thickness of the thrust washer.

Standard thickness:

5.95 to 6.05 mm (0.235 to 0.238 in.)


Minimum thickness:

5.95 mm (0.235 in.)


If the thickness is less than the minimum, replace the 1st gear thrust washer.



Hide 33037B 6.INSPECT NO. 1 SYNCHRONIZER RING SET (for 1st Gear)

a.
C315212

Apply gear oil to the cone of the 1st gear, and check that the No. 1 synchronizer ring set does not turn in either direction while pushing the No. 1 synchronizer ring set.

If No. 1 synchronizer ring set turns, replace it.



b.
C315213

Measure the clearance between the No. 1 synchronizer ring and 1st gear while pushing the No. 1 synchronizer ring against the cone of the 1st gear.

Standard clearance:

0.75 to 1.65 mm (0.0295 to 0.0650 in.)


If the clearance is not as specified, replace the No. 1 synchronizer ring with a new one.



Hide 33037B 7.INSPECT NO. 1 SYNCHRONIZER RING SET (for 2nd Gear)

a.
C315214

Apply gear oil to the cone of the 2nd gear, and check that No. 1 synchronizer ring set does not turn in either direction while pushing the No. 1 synchronizer ring set.

If No. 1 synchronizer ring set turns, replace it.



b.
C315215

Push the No. 1 synchronizer ring set against the cone of the 2nd gear. Measure the clearance between the No. 1 synchronizer ring set and 2nd gear.

Standard clearance:

0.65 to 1.75 mm (0.0256 to 0.0689 in.)


If the clearance is not as specified, replace the No. 1 synchronizer ring with a new one.



Hide 33368 8.INSPECT NO. 2 SYNCHRONIZER RING (for 3rd Gear)

a.
D026074

Apply gear oil to the cone of the 3rd gear, and check that No. 2 synchronizer ring does not turn in either direction while pushing the No. 2 synchronizer ring.

If the No. 2 synchronizer ring turns, replace it.



b.
D026075

Push the No. 2 synchronizer ring against the cone of the 3rd gear. Measure the clearance between the No. 2 synchronizer ring (for the 3rd gear) and 3rd gear.

Standard clearance:

0.75 to 1.65 mm (0.0295 to 0.0650 in.)


If the clearance is not as specified, replace the No. 2 synchronizer ring with a new one.



Hide 33331 9.INSPECT REVERSE GEAR

a.
C357749

Using a vernier caliper, measure the groove of the No. 1 shift fork and the thickness of flange of the reverse gear. Then calculate the clearance between the No. 1 shift fork and flange.

Standard clearance:

0.15 to 0.41 mm (0.00591 to 0.0161 in.)


If the clearance is not as specified, replace the reverse gear and No. 1 shift fork with new ones.



Hide 33361 10.INSPECT NO. 1 TRANSMISSION CLUTCH HUB

a.
D026077

Check the sliding condition between the No. 1 clutch hub and reverse gear.


b.

Check the spline of the reverse gear for wear.

If there are any defects, replace the No. 1 clutch hub.



Hide 33364 11.INSPECT NO. 2 TRANSMISSION HUB SLEEVE

a.
C357750

Using a vernier caliper, measure the groove of the No. 2 hub sleeve and the thickness of claw of the No. 2 shift fork. Then calculate the clearance between the No. 2 hub sleeve and the claw.

Standard clearance:

0.15 to 0.35 mm (0.00591 to 0.0138 in.)


If the clearance is not as specified, replace the No. 2 hub sleeve and No. 2 shift fork with new ones.



Hide 33362 12.INSPECT TRANSMISSION CLUTCH HUB NO. 2

a.
D026079

Check the sliding condition between the No. 2 clutch hub and No. 2 hub sleeve.


b.

Check the splines of the No. 1 clutch hub for wear.


c.

Check the tip of the spline gear sleeve of the reverse gear for wear.

If there are any defects, replace the No. 1 clutch hub or reverse gear.