Home › Drivetrain › R150F (MANUAL TRANSMISSION / TRANSAXLE) › OUTPUT SHAFT
RM27T0E _52 Drivetrain _053702 R150F MANUAL TRANSMISSION / TRANSAXLE _0260833 OUTPUT SHAFT A

R150F MANUAL TRANSMISSION / TRANSAXLE  OUTPUT SHAFT  DISASSEMBLY  


PROCEDURE

Hide 33335 1.INSPECT 1ST GEAR THRUST CLEARANCE

a.
C238808

Using a dial indicator, measure the thrust clearance.

Standard clearance:

0.20 to 0.45 mm (0.00787 to 0.0177 in.)


If the clearance is not as specified, replace the No. 1 synchronizer ring set.



Hide 33332 2.INSPECT 2ND GEAR THRUST CLEARANCE

a.
C238809

Using a dial indicator, measure the thrust clearance.

Standard clearance:

0.10 to 0.25 mm (0.00394 to 0.00984 in.)


If the clearance is not as specified, replace the No. 1 synchronizer ring set.



Hide 33333 3.INSPECT 3RD GEAR THRUST CLEARANCE

a.
D026045

Using a feeler gauge, measure the thrust clearance.

Standard clearance:

0.10 to 0.25 mm (0.00394 to 0.00984 in.)


If the clearance is not as specified, replace the No. 2 synchronizer ring set.



Hide 33335 4.INSPECT 1ST GEAR RADIAL CLEARANCE

a.
D026047

Using a dial indicator, measure the radial clearance.

Standard clearance:

0.020 to 0.073 mm (0.000785 to 0.00287 in.)


If the clearance is not as specified, replace the 1st gear needle roller bearing with a new one.



Hide 33332 5.INSPECT 2ND GEAR RADIAL CLEARANCE

a.
D026048

Using a dial indicator, measure the radial clearance.

Standard clearance:

0.015 to 0.068 mm (0.000591 to 0.00267 in.)


If the clearance is not as specified, replace the 2nd gear needle roller bearing with a new one.



Hide 33333 6.INSPECT 3RD GEAR RADIAL CLEARANCE

a.
D026049

Using a dial indicator, measure the radial clearance.

Standard clearance:

0.015 to 0.068 mm (0.000591 to 0.00267 in.)


If the clearance is not as specified, replace the 3rd gear needle roller bearing with a new one.



Hide 33335 7.REMOVE 1ST GEAR

a.
C216007E01
1.969,0.406 2.267,0.545 0.298,0.138 10 SST 1.931,0.499 1.652,0.499 false 1.652,0.499 1.526,1.107 false

Using SST and a press, remove the 5th gear, output shaft center bearing, 1st gear thrust washer and 1st gear from the output shaft.

SST
09950-00020  


Hide 33037B 8.REMOVE NO. 1 SYNCHRONIZER RING SET (for 1st Gear)

a.
C216216

Remove the synchronizer rings from the output shaft.


Hide 33348A 9.REMOVE 1ST GEAR THRUST WASHER PIN

a.

Remove the thrust washer pin from the output shaft.


Hide 33335C 10.REMOVE 1ST GEAR NEEDLE ROLLER BEARING

a.

Remove the needle roller bearing from the output shaft.


Hide 33335B 11.REMOVE 1ST GEAR BEARING SPACER

a.

Remove the bearing spacer from the output shaft.


Hide 33321M 12.REMOVE BEARING SHAFT SNAP RING

a.
D026055

Using 2 screwdrivers and a hammer, tap off the snap ring from the output shaft.

NOTICE:

Use a piece of cloth to prevent the snap ring from flying off.



Hide 33332 13.REMOVE 2ND GEAR

a.
C216008E01
0.278,0.269 0.583,0.430 0.305,0.161 10 SST 0.664,0.361 0.935,0.361 false 0.935,0.361 1.11,0.956 false

Using SST and a press, remove the No. 1 transmission clutch hub with the reverse gear, the No. 1 synchronizer ring set and the 2nd gear from the output shaft.

SST
09950-00020  


Hide 33332B 14.REMOVE 2ND GEAR NEEDLE ROLLER BEARING

a.

Remove the needle roller bearing from the output shaft.


Hide 33331 15.REMOVE REVERSE GEAR

a.
D026058

Remove the reverse gear, 3 No. 1 synchromesh shifting keys and 3 synchromesh shifting key springs.

NOTICE:

Use a piece of cloth to prevent the shifting keys and shifting key springs from popping out.



Hide 33321D 16.REMOVE CLUTCH HUB SET SHAFT SNAP RING

a.
D026059

Using a snap ring expander, remove the snap ring from the output shaft.

NOTICE:

Do not damage the sliding surface of the bearing.



Hide 33333 17.REMOVE 3RD GEAR

a.
C216009E01
0.391,0.459 0.709,0.605 0.318,0.147 10 SST 0.792,0.539 1.083,0.539 false 1.083,0.539 1.151,0.956 false

Using SST and a press, remove the No. 2 transmission clutch hub with the No. 2 transmission hub sleeve, the No. 2 synchronizer ring and the 3rd gear from the output shaft.

SST
09950-00020  


Hide 33333A 18.REMOVE 3RD GEAR NEEDLE ROLLER BEARING

a.

Remove the needle roller bearing from the output shaft.


Hide 33364 19.REMOVE NO. 2 TRANSMISSION HUB SLEEVE

a.
D033571

Remove the No. 2 hub sleeve, 3 No. 2 synchromesh shifting key springs and 3 No. 2 synchromesh shifting keys from the No. 2 clutch hub.