1.REMOVE HOSE
Detach the clamp and remove the hose.
36102D
2.REMOVE TRANSFER BEARING RETAINER SUB-ASSEMBLY RH
Remove the 5 bolts and transfer bearing retainer sub-assembly RH.
If necessary, tap the transfer bearing retainer sub-assembly RH with a plastic-faced hammer to remove it.
for RA61F:
Remove the O-ring from the transfer bearing retainer sub-assembly RH.
36102F
3.REMOVE TRANSFER BEARING RETAINER OIL SEAL RH
for A750F, AC60F, G52F, R150F:
Using a screwdriver and hammer, remove the transfer bearing retainer oil seal RH from the transfer bearing retainer sub-assembly RH.
for RA61F:
Using a screwdriver and hammer, remove the 2 transfer bearing retainer oil seals RH from the transfer bearing retainer sub-assembly RH.
36102
4.REMOVE TRANSFER CASE COVER SUB-ASSEMBLY
Remove the 4 bolts and transfer case cover sub-assembly.
36108A
5.REMOVE BREATHER OIL DEFLECTOR
Remove the breather oil deflector.
33309C
6.REMOVE FRONT OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY
Using a chisel and hammer, loosen the staked part of the lock nut.
Using SST to hold the front output shaft companion flange sub-assembly, remove the lock nut.
| *a | Turn |
| *b | Hold |
Using SST, remove the companion flange.
33309D
7.REMOVE FRONT TRANSFER OUTPUT SHAFT COMPANION FLANGE OIL SEAL
Using a screwdriver and hammer, tap out the oil seal from the companion flange.
Be careful not to damage the oil seal and companion flange contact surfaces.
36111B
8.REMOVE TRANSFER CASE FRONT OIL SEAL
33309C
9.REMOVE REAR OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY
Using a chisel and hammer, loosen the staked part of the lock nut.
Using SST to hold the companion flange, remove the lock nut.
Using SST, remove the companion flange.
33309D
10.REMOVE REAR TRANSFER OUTPUT SHAFT COMPANION FLANGE OIL SEAL
Using a screwdriver and hammer, tap out the oil seal from the companion flange.
Be careful not to damage the oil seal and companion flange contact surfaces.
36115C
11.REMOVE TRANSFER CASE REAR OIL SEAL
36105
12.REMOVE TRANSFER EXTENSION HOUSING SUB-ASSEMBLY
Remove the 5 bolts and extension housing.
If necessary, tap the extension housing with a plastic-faced hammer to remove it.
33309H
13.REMOVE TRANSFER OUTPUT SHAFT WASHER
Remove the 2 washers.
14.REMOVE COLLAR
Remove the collar.
36112
15.REMOVE REAR TRANSFER CASE
Remove the 12 bolts and clamp.
Remove the rear transfer case.
If necessary, tap the rear transfer case with a plastic-faced hammer to remove it.
16.REMOVE NO. 2 TRANSFER GEAR SHIFT FORK SUB-ASSEMBLY WITH TRANSFER HIGH AND LOW CLUTCH SLEEVE
Remove the bolt, No. 2 gear shift fork, and high and low clutch sleeve.
41408
17.REMOVE CENTER DIFFERENTIAL LOCK FORK SUB-ASSEMBLY WITH FRONT DRIVE CLUTCH SLEEVE
Using 2 screwdrivers and a hammer, tap off the snap ring.
Remove the bolt, center differential lock fork and front drive clutch sleeve.
18.REMOVE REAR OUTPUT SHAFT SUB-ASSEMBLY, FRONT DRIVE CHAIN AND DRIVEN SPROCKET SUB-ASSEMBLY
Mount the rear transfer case in a vise.
Using a snap ring expander, remove the snap ring.
Using a plastic-faced hammer, carefully tap the rear transfer case, and remove the rear output shaft together with the front drive chain and driven sprocket.
Remove the rear output shaft, front drive chain and driven sprocket.
36292A
19.REMOVE TRANSFER DRIVEN SPROCKET BEARING
Using SST and a press, remove the driven sprocket bearing.
Be careful not to drop or damage the driven sprocket.
36212A
20.REMOVE TRANSFER INPUT GEAR RADIAL BALL BEARING
Using SST and a press, remove the transfer input gear radial ball bearing.
Be careful not to drop or damage the driven sprocket.
36410J
21.REMOVE TRANSFER SHIFT ACTUATOR ASSEMBLY
Using 2 screwdrivers and a hammer, tap off the 2 snap rings.
Remove the 3 bolts and transfer shift actuator assembly.
Remove the O-ring from the transfer shift actuator assembly.
36114B
22.REMOVE FILLER PLUG
Remove the filler plug and gasket.
36114B
23.REMOVE DRAIN PLUG
Remove the drain plug and gasket.
36104H
24.REMOVE TRANSFER OIL SEPARATOR SUB-ASSEMBLY
Remove the 3 bolts and oil separator.
33449D
25.REMOVE TRANSFER CASE MAGNET
36106
26.REMOVE TRANSFER OIL PUMP BODY SUB-ASSEMBLY
Remove the 3 bolts and oil pump body.
36104J
27.REMOVE TRANSFER OIL PUMP BODY O-RING
Using a screwdriver, remove the oil pump body O-ring.
Be careful not to damage the oil pump body.
36227
28.REMOVE TRANSFER OIL PUMP GEAR
Remove the transfer oil pump gear.
29.REMOVE LOW PLANETARY GEAR ASSEMBLY WITH TRANSFER INPUT SHAFT SUB-ASSEMBLY
Using a snap ring expander, remove the snap ring.
Remove the low planetary gear together with the input shaft.
36231A
30.REMOVE TRANSFER OUTPUT SHAFT SPACER
Remove the transfer output shaft spacer.
36231E
31.REMOVE TRANSFER OUTPUT SHAFT FRONT NEEDLE ROLLER BEARING
Remove the needle roller bearing.
36213B
32.REMOVE TRANSFER INPUT GEAR STOPPER SHAFT SNAP RING
Using a snap ring expander, remove the snap ring.
36213
33.REMOVE TRANSFER INPUT GEAR STOPPER
Remove the input gear stopper.
36213A
34.REMOVE TRANSFER INPUT GEAR STOPPER BALL
Remove the ball.
33309H
35.REMOVE MANUAL TRANSFER PLANETARY CARRIER WASHER
Remove the washer.
36211
36.REMOVE TRANSFER INPUT SHAFT
Remove the transfer input shaft.
36288
37.REMOVE NO. 1 TRANSFER THRUST BEARING RACE
Remove the thrust bearing race.
36270A
38.REMOVE TRANSFER LOW PLANETARY GEAR THRUST BEARING
Remove the bearing.
36216A
39.REMOVE NO. 1 TRANSFER INPUT SHAFT SEAL RING
Remove the 2 seal rings.
36210A
40.REMOVE TRANSFER INPUT SHAFT BEARING
Using a snap ring expander, remove the snap ring.
Using SST and a press, remove the input shaft bearing.
Be careful not to drop or damage the low planetary gear.
36284
41.REMOVE TRANSFER LOW PLANETARY GEAR SPLINE PIECE
Using a screwdriver, remove the snap ring.
Remove the low planetary gear spline piece.
36270A
42.REMOVE TRANSFER LOW PLANETARY GEAR BEARING
Using SST, remove the low planetary gear bearing.
Make sure SST fits securely in the space between the bearing and low planetary gear.
36256
43.REMOVE NO. 2 TRANSFER OUTPUT SHAFT SPACER
Using a snap ring expander, remove the snap ring.
Remove the spacer.
36255A
44.REMOVE TRANSFER OUTPUT SHAFT SPACER BALL
Remove the ball.
41311M
45.REMOVE CENTER DIFFERENTIAL CASE
Remove the center differential case.
36237
46.REMOVE TRANSFER CLUTCH HUB
Remove the transfer clutch hub.
36231E
47.REMOVE TRANSFER OUTPUT SHAFT FRONT NEEDLE ROLLER BEARING
Remove the needle roller bearing.
36231D
48.REMOVE TRANSFER OUTPUT SHAFT PLATE WASHER
Remove the washer.
36231J
49.REMOVE REAR TRANSFER OUTPUT SHAFT RADIAL BALL BEARING
Using SST and a press, remove the bearing.
36255
50.REMOVE NO. 1 TRANSFER OUTPUT SHAFT SPACER
Remove the output shaft spacer.
36205
51.REMOVE TRANSFER DRIVE SPROCKET SUB-ASSEMBLY
Remove the transfer drive sprocket.
36291A
52.REMOVE TRANSFER DRIVE SPROCKET BEARING
Remove the bearing.
36231D
53.REMOVE TRANSFER OUTPUT SHAFT PLATE WASHER
Remove the washer.
36111C
54.REMOVE TRANSFER CASE PLUG
Remove the transfer case plug.
41331A
55.REMOVE COMPRESSION SPRING
Remove the spring.
36111G
56.REMOVE PIN
Remove the pin.
36273
57.REMOVE TRANSFER LOW PLANETARY RING GEAR
Using a screwdriver, remove the snap ring.
Remove the low planetary ring gear from the front transfer case.