Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT PROPELLER SHAFT ASSEMBLY
RM27T0E _52 Drivetrain _053704 DRIVE SHAFT / PROPELLER SHAFT _0260851 FRONT PROPELLER SHAFT ASSEMBLY A

DRIVE SHAFT / PROPELLER SHAFT  FRONT PROPELLER SHAFT ASSEMBLY  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL FRONT PROPELLER SHAFT UNIVERSAL JOINT SPIDER BEARING

HINT:

Use the same procedure for all propeller shaft universal joint spider bearing.


a.
Z004248

Apply MP grease to a new spider and spider bearing.

NOTICE:

Be careful not to apply too much grease.



b.

Install the universal joint spider to the propeller shaft.


c.
C359170E01
0.76,0.406 1.01,0.406 1.01,0.406 1.01,0.823 false 0.458,0.333 0.917,0.531 0.458,0.198 10 false SST

Using SST, install 2 of the spider bearings to the universal joint spider.

SST
09332-25010  


d.

Using SST, adjust both bearings so that the snap ring grooves are at maximum and equal width.

SST
09332-25010  


e.
G020755

Install 4 new snap rings of equal thickness which will allow no axial play.

HINT:

Do not reuse the snap rings.


Standard Snap Ring:
Part No. Mark Specified Condition
90520-25039 1 2.28 to 2.30 mm
(0.0898 to 0.0905 in.)
90520-25040 2 2.30 to 2.32 mm
(0.0906 to 0.0913 in.)
90520-25041 - 2.32 to 2.34 mm
(0.0914 to 0.0921 in.)
90520-25042 Brown 2.34 to 2.36 mm
(0.0922 to 0.0929 in.)
90520-25043 Blue 2.36 to 2.38 mm
(0.0930 to 0.0937 in.)
90520-25044 6 2.38 to 2.40 mm
(0.0938 to 0.0944 in.)
90520-25045 7 2.40 to 2.42 mm
(0.0945 to 0.0952 in.)
90520-25046 8 2.42 to 2.44 mm
(0.0953 to 0.0960 in.)
90520-25047
C262545

2.44 to 2.46 mm
(0.0961 to 0.0968 in.)
90520-25048 10 2.46 to 2.48 mm
(0.0969 to 0.0976 in.)
90520-25049 A 2.48 to 2.50 mm
(0.0977 to 0.0984 in.)
90520-25050 B 2.50 to 2.52 mm
(0.0985 to 0.0992 in.)
90520-25051 C 2.52 to 2.54 mm
(0.0992 to 0.0999 in.)
90520-25052 D 2.54 to 2.56 mm
(0.1000 to 0.1007 in.)
90520-25053 E 2.56 to 2.58 mm
(0.1008 to 0.1015 in.)
90520-25054 J 2.18 to 2.20 mm
(0.0859 to 0.0866 in.)
90520-25055 K 2.20 to 2.22 mm
(0.0867 to 0.0874 in.)
90520-25056 F 2.22 to 2.24 mm
(0.0875 to 0.0881 in.)
90520-25057 G 2.24 to 2.26 mm
(0.0882 to 0.0889 in.)
90520-25058 H 2.26 to 2.28 mm
(0.0890 to 0.0897 in.)


NOTICE:
·

Use a new retainer ring.

·

Use retainer rings with as close the same thickness as possible on both ends.




f.
G022297E12
1.292,0.208 1.51,0.385 0.219,0.177 10 false *a

Using a hammer, tap the yoke until there is no clearance between the spider bearing outer race and snap ring.

Text in Illustration
*a Hammering Point

HINT:

Install a new spider bearing on the sleeve side using the procedure described above.



g.

Align the matchmarks on the flange yoke and sleeve yoke.


h.
F044258E09
1.479,1.521 1.115,1.271 false 1.313,1.521 1.604,1.677 0.292,0.156 10 false SST

Using SST, install the spider bearings to the universal joint spider.

SST
09332-25010  


i.

Using SST, adjust both bearings so that the snap ring grooves are at maximum and equal in width.

SST
09332-25010  


j.

Install 4 new snap rings of equal thickness which will allow 0 mm (0 in.) of axial play.

HINT:

Do not reuse the snap rings.


Standard Snap Ring:
Part No. Mark Specified Condition
90520-25039 1 2.28 to 2.30 mm
(0.0898 to 0.0905 in.)
90520-25040 2 2.30 to 2.32 mm
(0.0906 to 0.0913 in.)
90520-25041 - 2.32 to 2.34 mm
(0.0914 to 0.0921 in.)
90520-25042 Brown 2.34 to 2.36 mm
(0.0922 to 0.0929 in.)
90520-25043 Blue 2.36 to 2.38 mm
(0.0930 to 0.0937 in.)
90520-25044 6 2.38 to 2.40 mm
(0.0938 to 0.0944 in.)
90520-25045 7 2.40 to 2.42 mm
(0.0945 to 0.0952 in.)
90520-25046 8 2.42 to 2.44 mm
(0.0953 to 0.0960 in.)
90520-25047
C262545

2.44 to 2.46 mm
(0.0961 to 0.0968 in.)
90520-25048 10 2.46 to 2.48 mm
(0.0969 to 0.0976 in.)
90520-25049 A 2.48 to 2.50 mm
(0.0977 to 0.0984 in.)
90520-25050 B 2.50 to 2.52 mm
(0.0985 to 0.0992 in.)
90520-25051 C 2.52 to 2.54 mm
(0.0992 to 0.0999 in.)
90520-25052 D 2.54 to 2.56 mm
(0.1000 to 0.1007 in.)
90520-25053 E 2.56 to 2.58 mm
(0.1008 to 0.1015 in.)
90520-25054 J 2.18 to 2.20 mm
(0.0859 to 0.0866 in.)
90520-25055 K 2.20 to 2.22 mm
(0.0867 to 0.0874 in.)
90520-25056 F 2.22 to 2.24 mm
(0.0875 to 0.0881 in.)
90520-25057 G 2.24 to 2.26 mm
(0.0882 to 0.0889 in.)
90520-25058 H 2.26 to 2.28 mm
(0.0890 to 0.0897 in.)


NOTICE:
·

Use a new retainer ring.

·

Use retainer rings with as close to the same thickness as possible on both ends.




k.
G022298E08
2.104,2.021 2.802,2.021 false 1.781,1.938 1.958,2.104 0.177,0.167 10 false *a

Using a plastic-faced hammer, tap the yoke until there is no clearance between the spider bearing outer race and snap ring.

Text in Illustration
*a Hammering Point

HINT:

Install a new spider bearing on the sleeve side using the procedure described above.



Hide 37110 2.INSPECT PROPELLER SHAFT ASSEMBLY

HINT:
·

When replacing a spider bearing, be sure that the grease fitting hole is facing the direction shown in the illustration.

·

Fill the grease fittings with MP grease.



C359175E01
0.052,0.073 0.365,0.271 0.313,0.198 10 false *a 2.604,0.344 2.917,0.542 0.313,0.198 10 false *b

Text in Illustration
*a Spider Grease Fitting Assembly Direction for Front Propeller Shaft Assembly *b Rear Side

Hide 3.INSPECT FRONT PROPELLER SHAFT UNIVERSAL JOINT SPIDER BEARING