Home › Drivetrain › AXLE AND DIFFERENTIAL › FRONT DIFFERENTIAL CARRIER ASSEMBLY
RM27T0E _52 Drivetrain _053705 AXLE AND DIFFERENTIAL _0260863 FRONT DIFFERENTIAL CARRIER ASSEMBLY A

AXLE AND DIFFERENTIAL  FRONT DIFFERENTIAL CARRIER ASSEMBLY  DISASSEMBLY  


PROCEDURE

Hide 1.INSPECT DIFFERENTIAL RING GEAR BACKLASH

R012683E15
1.583,1.271 0.667,0.99 false 0.323,0.906 0.625,1.052 0.302,0.146 10 false SST

a.

Using SST and a dial indicator, measure the ring gear backlash.

SST
09564-32011  

Standard backlash:

0.09 to 0.21 mm (0.00355 to 0.00826 in.)


If the backlash is not as specified, adjust the side bearing preload or perform repairs as necessary.

HINT:

Perform the measurement at 3 or more positions around the circumference of the ring gear.



Hide 41204D 2.INSPECT FRONT DRIVE PINION COMPANIONFLANGE SUB-ASSEMBLY

F001237E42
0.885,0.052 1.104,0.219 0.219,0.167 10 false *a 2.5,0.052 2.708,0.198 0.208,0.146 10 false *b

a.

Using a dial indicator, measure the runout of the companion flange vertically and laterally.

Distance from center to runout measurement point:

30 mm (1.18 in.)


Maximum Runout:
Item Specified Condition
Vertical runout 0.15 mm (0.00591 in.)
Lateral runout 0.15 mm (0.00591 in.)


Text in Illustration
*a Vertical Runout
*b Lateral Runout

If the runout is more than the maximum, replace the companion flange.


Hide 41320 3.REMOVE FRONT DIFFERENTIAL TUBE ASSEMBLY

a.
C097021

Using an E14 "TORX" socket wrench, remove the 4 bolts.


b.

Using a plastic-faced hammer, tap out the differential tube.


Hide 41304P 4.REMOVE DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL

a.
R013209E06
2.042,0.573 1.344,0.969 false 2.073,0.458 2.365,0.635 0.292,0.177 10 false SST

Using SST, remove the 2 oil seals.

SST
09308-00010  


Hide 41204E 5.REMOVE FRONT DRIVE PINION COMPANION FLANGE NUT

F044234E07
1.76,1.104 2.094,1.104 false 2.146,1.021 2.438,1.198 0.292,0.177 10 false SST

a.

Using SST and a hammer, unstake the nut.

SST
09930-00010  


b.
SA02349E18
2.604,0.792 2.896,0.563 false 2.948,0.448 3.24,0.615 0.292,0.167 8 false SST

Using SST to hold the companion flange, remove the nut.

SST
09330-00021  


Hide 41204D 6.REMOVE FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

F052175E18
2.01,0.792 2.313,1.094 false 2.229,1.115 2.521,1.292 0.292,0.177 10 false SST 0.271,1.188 0.521,1.385 0.25,0.198 10 false *a 2.365,0.125 2.573,0.333 0.208,0.208 10 false *b

a.

Using SST, remove the companion flange.

SST
09950-30012  (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03020)

Text in Illustration
*a Hold
*b Turn

NOTICE:

Before using SST (center bolt), apply hypoid gear oil to its threads and tip.



Hide 41252A 7.REMOVE FRONT DIFFERENTIAL DUST DEFLECTOR

F040564E19
2.354,0.333 2.646,0.49 0.292,0.156 10 false SST

a.

Using SST and a press, press out the dust deflector.

SST
09950-00020  
09950-60010  (09951-00510)
09950-70010  (09951-07150)

NOTICE:

Do not drop the companion flange.



Hide 41101D 8.REMOVE FRONT DIFFERENTIAL CARRIER OIL SEAL

a.
SA02348E16
1.146,0.594 1.344,0.802 false 0.771,0.479 1.104,0.646 0.333,0.167 10 false SST

Using SST, remove the oil seal from the differential carrier assembly.

SST
09308-10010  


Hide 41214C 9.REMOVE FRONT DIFFERENTIAL DRIVE PINION OIL SLINGER

a.

Remove the oil slinger from the drive pinion.


Hide 41211A 10.REMOVE FRONT DRIVE PINION FRONT TAPERED ROLLER BEARING (INNER)

a.
F044343E13
2.604,0.531 2.604,0.115 false 2.604,0.115 2.792,0.115 false 2.844,0.031 3.156,0.177 0.313,0.146 10 false SST

Using SST, remove the front tapered roller bearing (inner) from the drive pinion.

SST
09556-22010  


Hide 41211A 11.REMOVE FRONT DRIVE PINION FRONT TAPERED ROLLER BEARING (OUTER)

a.
W001770E12
1.927,0.719 1.927,0.094 false 1.927,0.094 2.156,0.094 false 2.219,0.031 2.552,0.198 0.333,0.167 10 false SST

Using SST, remove the front tapered roller bearing (outer).

SST
09308-00010  


Hide 41115 12.REMOVE FRONT DIFFERENTIAL OIL STORAGE RING

a.

Using a screwdriver and hammer, tap out the oil storage ring.


Hide 41231F 13.REMOVE FRONT DIFFERENTIAL DRIVE PINION BEARING SPACER

C093595

a.

Remove the bearing spacer.


Hide 14.REMOVE DIFFERENTIAL SIDE BEARING RETAINER

a.

Using a screwdriver, remove the union.


b.

Remove the 10 bolts and tap out the side bearing retainer with a plastic-faced hammer.


Hide 15.REMOVE DIFFERENTIAL CASE ASSEMBLY

Hide 16.REMOVE DIFFERENTIAL DRIVE PINION

Hide 41211B 17.REMOVE FRONT DRIVE PINION REAR TAPERED ROLLER BEARING (INNER)

a.
R002482E09
0.75,1.073 0.458,1.313 0.458,1.313 1.031,1.563 false 0.094,1.219 0.385,1.375 0.292,0.156 10 false SST

Using SST and a press, remove the rear tapered roller bearing (inner) and washer from the drive pinion.

SST
09950-00020  

HINT:

If the drive gear or ring gear is damaged, replace them as a set.


NOTICE:

Do not drop the drive pinion.



Hide 41211B 18.REMOVE FRONT DRIVE PINION REAR TAPERED ROLLER BEARING (OUTER)

a.
R013226

Using a brass bar and hammer, remove the rear tapered roller bearing (outer).


Hide 41311A 19.REMOVE FRONT DIFFERENTIAL CASE BEARING

R013211E06
0.938,0.615 0.375,0.49 0.375,0.49 0.844,0.948 false 0.01,0.396 0.302,0.573 0.292,0.177 10 false SST

HINT:
·

Measure the thickness of the case washer.

·

Tag the bearing outer races so that they can be reinstalled in the correct locations.



a.

Using SST and a press, press out the case bearing (outer race) and case washer from the bearing retainer.

SST
09950-60020  (09951-00680)
09950-70010  (09951-07150)

If the bearing is damaged during removal, replace it.


b.
R013213E06
1.146,0.583 0.458,0.479 0.458,0.479 1.031,0.885 false 0.104,0.396 0.396,0.573 0.292,0.177 10 false SST

Using SST and a press, press out the case bearing (outer race) and plate washer from the differential carrier.

SST
09950-60020  (09951-00680)
09950-70010  (09951-07150)

If the bearing is damaged during removal, replace it.


Hide 20.REMOVE DIFFERENTIAL RING GEAR

C113176E02
2.491,0.057 2.730,0.212 0.239,0.155 10 *a 1.922,1.068 2.444,0.156 false 2.444,0.156 1.965,1.175 false

a.

Place matchmarks on the ring gear and differential case.

Text in Illustration
*a Matchmark


b.

Remove the 10 ring gear set bolts.


c.
C014054

Using a plastic-faced hammer, tap on the ring gear to separate it from the differential case.


Hide 41311A 21.REMOVE FRONT DIFFERENTIAL CASE BEARING

HINT:

The differential case and case bearings should only be removed when replacement is necessary.


a.
R011392E09
1.719,1.49 1.927,1.875 false 1.719,1.49 1.927,1.875 false 0.979,0.479 1.229,0.802 false 3.156,1.74 2.802,1.615 false 0.615,0.344 0.927,0.5 0.313,0.156 10 false SST 1.771,1.875 2.073,2.031 0.302,0.156 10 true SST 3.188,1.667 3.354,1.844 0.167,0.177 10 true *a

Using SST, remove the 2 differential case bearings (inner) from the differential case.

SST
09950-60010  (09951-00390)
09950-40011  (09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04061, 09957-04010, 09958-04011)

Text in Illustration
*a Notch

HINT:

Set the claws of SST into the notches in the differential case.



Hide 22.REMOVE DIFFERENTIAL CASE ASSEMBLY

a.
C080046

Using a chisel and hammer, unstake the differential case.


b.
G020264

Using a 5 mm pin punch and hammer, tap out the straight pin.


c.
C358690E01
0.885,3.052 0.885,2.719 0.885,2.719 1.135,2.719 false 0.521,2.927 0.521,2.552 0.521,2.552 0.771,2.552 false 1.333,3.323 1.333,2.99 1.333,2.99 1.583,2.99 false 1.927,2.875 1.927,2.542 1.927,2.542 2.073,2.542 false 2.604,2.698 2.854,2.698 false 2.438,3.646 2.438,3.469 2.438,3.469 2.583,3.469 false 2.781,3.813 2.781,3.635 2.781,3.635 2.927,3.635 false 1.292,3.938 1.542,3.938 false 0.802,4.281 1.052,4.281 false 1.188,2.625 1.5,2.823 0.313,0.198 10 false *1 0.823,2.479 1.135,2.677 0.313,0.198 10 false *2 1.625,2.906 1.938,3.104 0.313,0.198 10 false *3 2.115,2.469 2.427,2.667 0.313,0.198 10 false *4 2.885,2.615 3.198,2.813 0.313,0.198 10 false *5 2.625,3.375 2.938,3.573 0.313,0.198 10 false *1 2.979,3.552 3.292,3.75 0.313,0.198 10 false *2 1.604,3.875 1.917,4.073 0.313,0.198 10 false *4 1.104,4.198 1.417,4.396 0.313,0.198 10 false *5

Remove the parts shown in the illustration from the differential case.

Text in Illustration
*1 Differential Pinion Gear
*2 Differential Pinion Gear Thrust Washer
*3 Differential Pinion Shaft
*4 Differential Side Gear
*5 Differential Side Gear Thrust Washer


Hide 41039A 23.INSPECT DIFFERENTIAL GEAR KIT

a.

Check that the differential pinion and differential side gear are not damaged.

If the differential pinion or differential side gear is damaged, replace the differential gear kit.


Hide 41311 24.INSPECT FRONT DIFFERENTIAL CASE

a.

Check that the differential case is not damaged.

If the differential case is damaged, replace it.


Hide 41304P 25.REMOVE DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL

a.
R013199E10
1.125,1.302 1.635,1.677 false 1.667,1.625 1.958,1.802 0.292,0.177 10 false SST

Using SST, tap out the oil seal from the differential tube.

SST
09308-00010  


Hide 41304F 26.REMOVE DIFFERENTIAL SIDE GEAR SHAFT SUB-ASSEMBLY RH

a.
C097022

Using a snap ring expander, remove the snap ring.


b.

Remove the side gear shaft from the differential tube.


Hide 41311A 27.REMOVE FRONT DIFFERENTIAL SIDE GEAR SHAFT BEARING RH

a.
R013420E07
2.531,0.385 2.208,0.615 false 2.573,0.292 2.885,0.448 0.313,0.156 10 false SST

Using a snap ring expander, remove the snap ring.


b.

Using SST, a brass bar and press, press out the bearing.

SST
09950-00020  

NOTICE:
·

Do not damage the bearing.

·

Do not drop the shaft.