Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR DIFFERENTIAL CARRIER ASSEMBLY (w/ Differential Lock)
RM27T0E _52 Drivetrain _053705 AXLE AND DIFFERENTIAL _0260866 REAR DIFFERENTIAL CARRIER ASSEMBLY(w/ Differential Lock) A

AXLE AND DIFFERENTIAL  REAR DIFFERENTIAL CARRIER ASSEMBLY(w/ Differential Lock)  DISASSEMBLY  


PROCEDURE

Hide 41110 1.FIX REAR DIFFERENTIAL CARRIER ASSEMBLY IN PLACE

C217291

a.

Fix the rear differential carrier assembly to the overhaul attachment.


Hide 41204 2.INSPECT REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY REAR

F001237E44
0.104,0.021 0.313,0.188 0.208,0.167 10 false *a 2.073,0.021 2.26,0.167 0.188,0.146 10 false *b 1.896,1.781 2.354,1.938 0.458,0.156 10 true 30 mm

a.

Using a dial indicator, measure the runout of the companion flange vertically and laterally.

Distance from center to runout measurement point:

30 mm (1.18 in.)


Maximum Runout:
Item Specified Condition
Vertical runout 0.10 mm (0.00394 in.)
Lateral runout 0.10 mm (0.00394 in.)


Text in Illustration
*a Vertical Runout
*b Lateral Runout

If the runout is more than the maximum, replace the companion flange.


Hide 3.INSPECT RUNOUT OF DIFFERENTIAL RING GEAR

C217282

a.

Using a dial indicator, check the runout of the ring gear.

Maximum runout:

0.07 mm (0.00276 in.)


If the runout is more than the maximum, replace the ring gear with a new one.


Hide 4.INSPECT DIFFERENTIAL RING GEAR BACKLASH

C217283

a.

Using a dial indicator, check the backlash of the ring gear.

Standard backlash:

0.10 to 0.20 mm (0.00394 to 0.00787 in.)


If the backlash is not within the specification, adjust the side bearing preload or performs repairs as necessary.


Hide 5.INSPECT DIFFERENTIAL DRIVE PINION PRELOAD

C003092

a.

Using a torque wrench, measure the preload of the backlash between the drive pinion and ring gear.

Standard preload (at starting):

0.88 to 1.98 N*m (9.0 to 20.2 kgf*cm, 7.8 to 17.5 in.*lbf)


If necessary, disassemble and inspect the differential assembly.


Hide 6.INSPECT TOTAL PRELOAD

C003092

a.

Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.


b.

Using a torque wrench, measure the total preload.

Standard Total Preload (at starting):

Drive pinion preload plus 0.20 to 0.40 N*m (2.0 to 4.1 kgf*cm, 1.8 to 3.5 in.*lbf)


If necessary, disassemble and inspect the differential.


Hide 41450 7.REMOVE DIFFERENTIAL LOCK SHIFT ACTUATOR

G020268

a.

Remove the 4 bolts and actuator from the differential carrier.


b.

Remove the O-ring.


Hide 84222E 8.REMOVE DIFFERENTIAL LOCK INDICATOR SWITCH

G020269

a.

Remove the indicator switch and gasket.


Hide 41462K 9.REMOVE REAR DIFFERENTIAL LOCK SHIFT FORK SHAFT

G020270

a.

Using a 6 mm hexagon wrench, remove the 2 screw plugs.


b.

Remove the spring seat, spring and ball.


c.
G020271

Using a 5 mm pin punch and hammer, remove the slotted pin.


d.
G020272

Remove the 2 bolts from the shaft retainer.


e.

Using a plastic-faced hammer, remove the shaft retainer.


f.

Remove the shift fork shaft.


g.

Remove the rear differential lock sleeve.


Hide 41204B 10.REMOVE REAR DRIVE PINION NUT

F044346E15
1.76,1.063 2.333,1.063 false 2.365,0.969 2.688,1.125 0.323,0.156 10 false SST

a.

Using SST and a hammer, loosen the staked part of the nut.

SST
09930-00010  

NOTICE:
·

Be sure to use SST with the tapered surface facing the shaft.

·

Do not grind the tip of SST with a grinder, etc.

·

Completely loosen the staked part of the nut when removing.

·

Do not damage the threads of the drive pinion.




b.
SA02349E19
2.604,0.792 2.896,0.563 false 2.948,0.448 3.24,0.615 0.292,0.167 10 false SST

Use SST to hold the drive pinion companion flange.

SST
09330-00021  


c.

Using a 30 mm socket wrench, remove the rear drive pinion nut.


Hide 41204 11.REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY REAR

F052175E19
2.01,0.792 2.479,1.26 false 2.385,1.281 2.677,1.458 0.292,0.177 10 false SST

a.

Using SST, remove the drive pinion companion flange.

SST
09950-30012  (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)

NOTICE:

Apply grease to the threads and tip of SST center bolt before use.



Hide 41201C 12.REMOVE REAR DIFFERENTIAL CARRIER OIL SEAL

SA02348E17
1.146,0.594 1.344,0.802 false 0.771,0.479 1.104,0.646 0.333,0.167 10 false SST

a.

Using SST, remove the oil seal from the differential carrier.

SST
09308-10010  


Hide 41214 13.REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

NOTICE:

Apply grease to the threads and tip of SST center bolt before use.


Hide 41201B 14.REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING (INNER)

Z000641E15
0.938,0.531 1.677,0.75 false 0.594,0.438 0.906,0.594 0.313,0.156 10 false SST

a.

Using SST, remove the drive pinion tapered roller bearing from the drive pinion.

SST
09556-22010  

NOTICE:

Apply grease to the threads and tip of SST center bolt before use.



Hide 41201B 15.REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING (OUTER)

Hide 41316 16.REMOVE REAR DIFFERENTIAL BEARING ADJUSTING NUT LOCK

C217052

a.

Remove the 2 bolts and 2 rear differential bearing adjusting nut locks.


Hide 17.REMOVE DIFFERENTIAL CASE ASSEMBLY

C217292E05
2.031,1.875 2.583,1.781 2.583,1.781 2.021,1.979 false 2.583,1.688 2.781,1.844 0.198,0.156 10 true *a

a.

Place matchmarks on the bearing cap and differential carrier.

Text in Illustration
*a Matchmark


b.

Remove the 4 bolts and 2 differential bearing caps.


c.

Remove the 2 adjusting nuts.


d.
C217285

Remove the rear differential case sub-assembly and 2 case bearings from the differential carrier.

HINT:

Tag the 2 case bearing outer races so that they can be reinstalled in the correct locations.



Hide 18.REMOVE DIFFERENTIAL DRIVE PINION

C030540

a.

Remove the differential drive pinion and bearing spacer from the differential carrier.


Hide 41201A 19.REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING (INNER)

R010668E15
2.813,0.594 2.313,1.021 false 2.854,0.458 3.146,0.635 0.292,0.177 10 false SST

a.

Using SST and a press, remove the drive pinion tapered roller bearing from the drive pinion.

SST
09950-00020  

HINT:

If either the drive pinion or ring gear is damaged, replace them as a set.


NOTICE:

Do not drop the drive pinion.



Hide 41201A 20.REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING (OUTER)

C091047

a.

Using a brass bar and hammer, remove the rear tapered roller bearing from the carrier.

HINT:

If the bearing is damaged during the removal, replace it.



Hide 41201D 21.REMOVE REAR DIFFERENTIAL DRIVE PINION PLATE WASHER

Hide 22.REMOVE DIFFERENTIAL RING GEAR

C216547E02
1.284,1.983 1.512,2.172 0.229,0.189 1.284,1.988 1.461,2.156 0.178,0.169 10 *a 1.647,1.832 1.483,2.069 false 1.667,1.964 1.483,2.069 false

a.

Place matchmarks on the ring gear and differential case.

Text in Illustration
*a Matchmark


b.

Using a screwdriver and hammer, unstake the lock plates.


c.

Remove the 12 ring gear set bolts.


d.
C014054

Using a plastic-faced hammer, tap on the ring gear to separate it from the differential case.


Hide 41201B 23.REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

F044358E09
1.042,0.24 1.427,0.24 false 1.469,0.167 1.771,0.323 0.302,0.156 10 false SST

a.

Using SST, remove the front tapered roller bearing from the carrier.

SST
09308-00010  


b.

Using a brass bar and hammer, remove the oil storage ring from the carrier.

HINT:

If the bearing is damaged during the removal, replace it.



Hide 24.INSPECT DIFFERENTIAL CASE ASSEMBLY RUNOUT

G020277

a.

Install the rear differential case bearing to the differential case.


b.

Install the differential case to the differential carrier.


c.

Install the 2 bearing caps to the differential carrier with the 4 bolts.

Torque:
103 N*m (1049 kgf*cm, 76 ft.*lbf)


d.

Inspect the differential case runout.

Maximum runout:

0.07 mm (0.00276 in.)



e.

Remove the differential case.


f.

Remove the rear differential case bearing.


Hide 41301A 25.REMOVE REAR DIFFERENTIAL CASE BEARING

F040345E14
0.49,0.406 0.917,0.74 false 2.146,0.854 2.531,1.292 false 0.135,0.292 0.448,0.458 0.313,0.167 10 false SST 1.802,0.75 2.115,0.917 0.313,0.167 10 false SST

a.

Using SST, remove the 2 rear differential case bearings from the differential case.

SST
09950-40011  (09953-04020, 09951-04010, 09952-04010, 09954-04010, 09955-04061, 09957-04010, 09958-04011)
09950-60010  (09951-00500, 09951-00650, 09952-06010)


Hide 26. DISASSEMBLE DIFFERENTIAL CASE

F052178E08
1.823,1.302 1.719,1.885 false 1.073,1.448 1.448,1.875 1.448,1.875 1.052,1.635 false 1.469,1.875 1.677,2.052 0.208,0.177 10 false *a

a.

Place matchmarks on the LH and RH cases.

Text in Illustration
*a Matchmark


b.

Remove the 8 bolts.


c.
ZK09094

Using a plastic-faced hammer, separate the LH and RH cases.


d.
C090324E10
1.854,0.521 2,0.427 false 1.417,1.917 1.281,1.917 false 1.01,0.906 0.781,1.083 0.781,1.083 1.01,1.313 false 1.396,0.167 1.25,0.167 false 2.323,0.813 2.552,0.99 2.552,0.99 2.333,1.208 false 2.5,0.646 3.042,1 3.042,1 2.583,1.448 false 0.833,0.771 0.385,1.115 0.385,1.115 0.844,1.542 false 1.938,1.604 2.063,1.604 false 1.49,0.938 1.167,0.469 false 2,0.333 2.146,0.5 0.146,0.167 10 false *11 2.063,1.531 2.208,1.688 0.146,0.156 10 false *1 1.083,0.083 1.26,0.25 0.177,0.167 10 false *2 1.083,1.833 1.333,1.99 0.25,0.156 10 false *2 1,0.375 1.156,0.521 0.156,0.146 10 false *3 0.604,0.99 0.781,1.135 0.177,0.146 10 false *4 2.552,0.906 2.719,1.052 0.167,0.146 10 false *4 3.052,0.927 3.198,1.104 0.146,0.177 10 false *5 0.198,1.031 0.365,1.208 0.167,0.177 10 false *5

Remove the parts shown in the illustration from the differential case.

Text in Illustration
*1 Side Gear
*2 Side Gear Thrust Washer
*3 Spider
*4 Pinion Gear
*5 Pinion Gear Thrust Washer