Home › Suspension › FRONT SUSPENSION › FRONT SHOCK ABSORBER
RM27T0E _53 Suspension _053708 FRONT SUSPENSION _0260889 FRONT SHOCK ABSORBER A

FRONT SUSPENSION  FRONT SHOCK ABSORBER  REASSEMBLY  


PROCEDURE

Hide 48510H 1.INSTALL FRONT SHOCK ABSORBER BUSH

a.
C214442E01
2.777,1.165 3.125,1.453 0.348,0.288 10 SST 2.114,0.689 2.547,0.689 false 2.547,0.689 2.547,1.886 false 2.547,1.886 2.204,1.886 false 2.547,1.245 2.747,1.245 false

Using SST and a press, install a new absorber bush.

SST
09710-30012  (09710-04071, 09710-04081)


Hide 48132 2.INSTALL FRONT COIL SPRING LH

a.
C159782E02
0.115,0.613 0.414,0.758 0.3,0.145 10 SST 0.464,0.688 0.688,0.688 false 0.688,0.688 0.727,0.793 false

Secure SST in a vise.

SST
09727-30022  (09727-00010, 09727-00031)
09727-00060  


b.
C275706E04
0.303,0.093 0.473,0.253 0.170,0.161 10 *a 0.303,2.563 0.473,2.723 0.170,0.160 10 *b 2.101,1.14 2.417,1.303 0.317,0.163 10 SST 1.823,1.23 2.067,1.23 false 2.098,3.593 2.414,3.756 0.317,0.163 10 SST 1.82,3.683 2.064,3.683 false

Attach the arm of SST to the diameter of the coil spring.

Text in Illustration
*a Correct
*b Incorrect

CAUTION:
·

Make sure that the coil spring is installed so that the distance between the upper and lower hooks of SST is at the maximum.

·

Make sure that the claws of the hooks are securely attached.




c.

Using SST, compress the coil spring.

CAUTION:
·

If the coil spring bends during the compression, immediately stop the compression and reinstall SST.

·

Do not compress the spring until the coil springs contact each other.

·

Do not use an impact wrench.




d.
C155966E02
2.733,0.349 2.832,1.013 false 2.832,1.013 2.832,1.273 false 0.104,0.979 0.418,1.132 0.314,0.153 10 SST 0.705,1.06 0.476,1.06 false 2.725,1.291 2.936,1.488 0.211,0.197 10 *a

Install the coil spring to the shock absorber.

HINT:

Fit the lower end of the coil spring into the recess of the spring seat of the shock absorber.


Text in Illustration
*a Lower End


Hide 48609 3.INSTALL FRONT SUSPENSION SUPPORT SUB-ASSEMBLY LH

a.

Install the cushion, 2 retainers and suspension support to the piston rod.


b.

Temporarily install a new front shock absorber nut to the suspension support.


c.
U115989E01
0.287,0.068 0.551,0.286 0.264,0.218 10 *A 2.908,0.063 3.171,0.281 0.264,0.218 10 *B 1.589,1.537 1.790,1.703 0.200,0.166 10 *1 0.852,1.816 1.052,1.983 0.200,0.166 10 *2 1.226,1.199 1.712,1.366 false 1.712,1.366 1.712,1.512 false 0.965,1.644 0.965,1.8 false

Position the suspension support as shown in the illustration.

Text in Illustration
*A LH
*B RH
*1 Absorber Bush
*2 Suspension Support Sub-assembly
V100135

Front


d.

Remove SST.

HINT:

Release the coil spring while checking the position of the suspension support.


NOTICE:

Do not use an impact wrench. It will damage the shock absorber rod.



Hide 48680A 4.TIGHTEN FRONT SUPPORT TO FRONT SHOCK ABSORBER NUT

a.

Tighten a new nut.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)