Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster) › 2015.06–2017.08
RM27T0E _54 Brake _053712 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0260911 VEHICLE STABILITY CONTROL SYSTEM(for Hydraulic Brake Booster) U

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Hydraulic Brake Booster)  TERMINALS OF ECU  


TERMINALS OF ECU


U148489E01
0.211,0.085 0.459,0.303 0.248,0.218 10 *a 2.628,0.164 2.827,0.327 0.199,0.163 10 A7 5.68,0.166 5.889,0.329 0.209,0.163 10 A8

Text in Illustration
*a Component without harness connected
(Skid Control ECU)
- -

Terminal No. (Symbol) Terminal Description
A7-1 (GND1) Skid control ECU ground
A7-2 (+BM1) Power supply for motor
A7-3 (FR+) Front speed sensor RH power supply output
A7-4 (FL-) Front speed sensor LH input
A7-5 (RR+) Rear speed sensor RH power supply output
A7-6 (RL-) Rear speed sensor LH input
A7-7 (STP) Stop light switch
A7-9 (CSW) VSC OFF switch
A7-11 (CANH) CAN communication terminal high
A7-12 (SP1) Speedometer signal
A7-16 (STPO) Stop light operation relay
A7-17 (FR-) Front speed sensor RH input
A7-18 (FL+) Front speed sensor LH power supply output
A7-19 (RR-) Rear speed sensor RH input
A7-20 (RL+) Rear speed sensor LH power supply output
A7-24 (TS) Sensor test terminal (Signal check switch)
A7-25 (CANL) CAN communication terminal low
A7-27 (EXI) Center differential lock detection switch
A7-28 (HZRI) Hazard warning switch
A7-30 (BZ)*1 Skid control buzzer
A7-31 (+BS) Power supply for solenoid
A7-32 (GND2) Skid control ECU ground
A7-40 (EXI3) w/ Rear Differential Lock: Rear differential lock detection switch
w/o Rear Differential Lock: Four wheel drive control ECU
A7-41 (LBL) Brake fluid level warning switch
A7-42 (EXO) Stop light control relay (Emergency brake signal output)
A7-44 (HDCS)*2 Downhill assist control switch
A7-45 (STP2) Stop light switch
A7-46 (IG1) IG1 power supply
A8-1 (IG2) IG2 power supply
A8-2 (+BM2) Power supply for motor
A8-4 (GND3) Skid control ECU ground

*1: w/ Dynamic Radar Cruise Control System

*2: w/ Downhill Assist Control



TERMINAL INSPECTION


Disconnect the 2 skid control ECU connectors and measure the voltage or resistance on the wire harness side.

HINT:

Voltage cannot be measured with the connector connected to the skid control ECU as the connector is watertight.


U148196E01
0.258,0.166 0.524,0.369 0.266,0.203 10 *a 2.098,1.014 2.302,1.189 0.205,0.175 10 A7 5.531,1.006 5.729,1.181 0.198,0.175 10 A8

Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU)
- -

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A7-2 (+BM1) - Body ground B Power supply for motor
(from battery)
Always 11 to 14 V
A7-7 (STP) - Body ground V Stop light switch Brake pedal depressed → released 8 to 14 V → Below 1.5 V
A7-9 (CSW) - Body ground B VSC OFF switch input VSC OFF switch off → on and held 10 kΩ or higher → Below 1 Ω
A7-16 (STPO) - Body ground LG Stop light operation relay Always 11 to 14 V
A7-31 (+BS) - Body ground L-R Power supply for solenoid
(from battery)
Always 11 to 14 V
A7-41 (LBL) - Body ground V-G Brake fluid level warning switch Brake fluid level +/-5 mm (+/-0.196 in.) from minimum level → maximum level Below 1 Ω → 1.9 to 2.1 kΩ
A7-44 (HDCS)* - Body ground W-L Downhill assist control switch input Downhill assist control switch off → on 10 kΩ or higher → Below 1 Ω
A7-45 (STP2) - Body ground L Stop light switch Brake pedal depressed → released 8 to 14 V → Below 1.5 V
A7-46 (IG1) - Body ground G IG1 power supply Ignition switch off → ON Below 1 V → 11 to 14 V
A8-1 (IG2) - Body ground W IG2 power supply Ignition switch off → ON Below 1 V → 11 to 14 V
A8-2 (+BM2) - Body ground B Power supply for motor
(from battery)
Always 11 to 14 V
A7-1 (GND1) - Body ground W-B Ground Always Below 1 Ω
A7-32 (GND2) - Body ground W-B Ground Always Below 1 Ω
A8-4 (GND3) - Body ground W-B Ground Always Below 1 Ω

*: w/ Downhill Assist Control