Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster) › 2015.06–2017.08
RM27T0E _54 Brake _053712 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0260912 VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster) U

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)  TERMINALS OF ECU  


TERMINALS OF ECU


C197053E04
0.139,0.087 0.410,0.276 0.272,0.188 10 *a

Text in Illustration
*a Component without harness connected
(Skid Control ECU [Brake Actuator Assembly])

Terminal No. (Symbol) Terminal Description
1 (GND1) Skid control ECU ground
2 (STP) Stop light switch input
4 (RL-) Rear wheel speed LH (-) signal input
5 (RL+) Rear wheel speed LH (+) power supply output
6 (FR-) Front wheel speed RH (-) signal input
7 (FR+) Front wheel speed RH (+) power supply output
8 (EXO) Stop light control ECU output
9 (EXI4) Center differential lock detection switch input
11 (SP1) Speed signal output for speedometer
12 (+BS) Solenoid relay power supply
13 (GND2) Pump motor ground
14 (CANL) CAN communication line low
16 (RR-) Rear wheel speed RH (-) signal input
17 (RR+) Rear wheel speed RH (+) power supply output
18 (FL-) Front wheel speed LH (-) signal input
19 (FL+) Front wheel speed LH (+) power supply output
22 (STP2) Stop light control ECU input
24 (BM) Motor relay power supply
25 (CANH) CAN communication line high
27 (FSW+) Brake pedal load sensing switch input
29 (HZRI) Hazard warning switch input
30 (CSW) VSC OFF switch input
33 (TS) Sensor check input
34 (IG1) ECU power supply


TERMINAL INSPECTION


U148257E01
0.213,0.072 0.501,0.270 0.288,0.198 10 *a 1.685,0.151 1.911,0.316 0.225,0.165 10 A6

Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])

a.

Disconnect the connector and measure the voltage or resistance on the wire harness side.

HINT:

Voltage cannot be measured with the connector connected to the skid control ECU (brake actuator assembly) as the connector is watertight.


i.

Disconnect the skid control ECU (brake actuator assembly) connector.


ii.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A6-1 (GND1) - Body ground W-B - Body ground Skid control ECU ground Always Below 1 Ω
A6-2 (STP) - Body ground V - Body ground Stop light switch input Brake pedal depressed → released 8 to 14 V → Below 1.5 V
A6-12 (+BS) - Body ground L-R - Body ground Solenoid relay power supply Always 11 to 14 V
A6-13 (GND2) - Body ground W-B - Body ground Pump motor ground Always Below 1 Ω
A6-22 (STP2) - Body ground L - Body ground Stop light control ECU input Brake pedal depressed → released 8 to 14 V → Below 1.5 V
A6-24 (BM) - Body ground B - Body ground Motor relay power supply Always 11 to 14 V
A6-25 (CANH) - A6-14 (CANL) B - W CAN bus Ignition switch off 54 to 69 Ω
A6-27 (FSW+) - Body ground V-G - Body ground Brake pedal load sensing switch input Brake pedal depressed → released 950 to 1050 Ω → 203 to 223 Ω
A6-30 (CSW) - Body ground B - Body ground VSC OFF switch input VSC OFF switch held on → off (Not pressed) Below 1 Ω → 10 kΩ or higher
A6-34 (IG1) - Body ground G - Body ground ECU power supply Ignition switch ON 11 to 14 V