Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster) › 2015.06–2017.08
RM27T0E _54 Brake _053712 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0260912 VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)  U0073  Control Module Communication Bus OFF  U0100  Lost Communication with ECM / PCM  U0114  Lost Communication with 4WD Control ECU  U0123  Lost Communication with Yaw Rate Sensor Module  U0124  Lost Communication with Lateral Acceleration Sensor Module  U0126  Lost Communication with Steering Angle Sensor Module  


DESCRIPTION

The skid control ECU receives signals from the ECM, the steering angle sensor and the yaw rate and acceleration sensor via the CAN communication system.

DTC Code DTC Detection Condition Trouble Area
U0073 One of the following conditions is met:
1.

When the IG1 terminal voltage is between 10 and 17.4 V, after the output of data from the skid control ECU is completed, the sending operation continues for 5 seconds or more.

2.

The condition that the bus OFF state occurs once or more within 0.1 seconds occurs 10 times in succession (sent signals cannot be received).

3.

When the IG1 terminal voltage is between 10 and 17.4 V, a delay in receiving data from the yaw rate and acceleration sensor and steering angle sensor continues for 1 second or more.

4.

When the IG1 terminal voltage is between 10 and 17.4 V, the following occurs 10 times in succession.

-

The condition that a delay in receiving data from the yaw rate and acceleration sensor and steering angle sensor occurs more than once within 5 seconds.



CAN communication system
U0100 Either condition is met:
1.

When the IG1 terminal voltage is between 10 and 17.4 V and the vehicle speed is 15 km/h (9 mph) or more, data cannot be sent to the ECM for 2 seconds or more.

2.

When the IG1 terminal voltage is between 10 and 17.4 V and the vehicle speed is 15 km/h (9 mph) or more, data cannot be received from the ECM for 2 seconds or more.


CAN communication system
U0114 The CAN signal from the four wheel drive control ECU is lost or malfunctioning for 1.2 seconds. CAN communication system
U0123 Either condition is met:
1.

When the IG1 terminal voltage is between 10 and 17.4 V, data from the yaw rate sensor cannot be received for 1 second or more.

2.

When the IG1 terminal voltage is between 10 and 17.4 V, the following occurs 10 times in succession.

-

The condition that data from the yaw rate sensor cannot be received occurs once or more within 5 seconds.



CAN communication system
U0124 Either condition is met:
1.

When the IG1 terminal voltage is between 10 and 17.4 V, data from the acceleration sensor cannot be received for 1 second or more.

2.

When the IG1 terminal voltage is between 10 and 17.4 V, the following occurs 10 times in succession.

-

The condition that data from the acceleration sensor cannot be received occurs once or more within 5 seconds.



CAN communication system
U0126 Either condition is met:
1.

When the IG1 terminal voltage is between 10 and 17.4 V, data from the steering angle sensor cannot be received for 1 second or more.

2.

When the IG1 terminal voltage is between 10 and 17.4 V, the following occurs 10 times in succession.

-

The condition that data from the steering angle sensor cannot be received occurs once or more within 5 seconds.



CAN communication system

PROCEDURE

1.RECONFIRM DTC
a.

Check for DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC not output A
DTC output for LHD without Entry and Start System B
DTC output for LHD with Entry and Start System C



A

B

C