Home › Brake › BRAKE SYSTEM (OTHER) › HYDRAULIC BRAKE BOOSTER(for RHD)
RM27T0E _54 Brake _053713 BRAKE SYSTEM (OTHER) _0260931 HYDRAULIC BRAKE BOOSTER(for RHD) A

BRAKE SYSTEM (OTHER)  HYDRAULIC BRAKE BOOSTER(for RHD)  DISASSEMBLY  


PROCEDURE

Hide 44591A 1.REMOVE NO. 1 BRAKE ACTUATOR BRACKET

a.
F051421

Using a 5 mm hexagon wrench, remove the bolt and No. 1 brake actuator bracket.


b.
F051180

Using a screwdriver, disconnect the brake fluid level warning switch connector from the No. 1 brake actuator bracket.


Hide 47202 2.REMOVE BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY

a.
C172197E07
1.708,1.24 1.354,1.75 1.354,1.75 1.167,1.75 true 0.958,1.677 1.125,1.833 0.167,0.156 10 false *1

Using a pin punch and hammer, remove the pin from the brake master cylinder reservoir.

Text in Illustration
*1 Pin Punch


b.
C172198

Remove the screw and pull out the brake master cylinder reservoir sub-assembly.


c.

Remove the master cylinder reservoir filler cap.


Hide 47255 3.REMOVE MASTER CYLINDER RESERVOIR GROMMET

a.
U149526

Remove the 3 reservoir grommets from the master cylinder reservoir.


Hide 44571A 4.REMOVE NO. 1 BRAKE ACTUATOR HOSE

a.
U116674

Using needle nose pliers, slide the 2 clips and remove the brake actuator hose and 2 clips.


Hide 44551C 5.REMOVE NO. 1 BRAKE ACTUATOR TUBE

a.
C213450

Using a union nut wrench, remove the No. 1 brake actuator tube.


Hide 47070B 6.REMOVE BRAKE BOOSTER WITH ACCUMULATOR PUMP ASSEMBLY

a.
U116675

Using a screwdriver, remove the 2 plugs.


b.
U116676

Remove the 2 screws and disconnect the wire harnesses from the master cylinder solenoid.


c.
F051187

Using a screwdriver, remove the clip.


d.
U116067

Remove the brake booster with accumulator pump assembly from the brake master cylinder.


e.

Remove the 2 brake booster pump collars and 2 brake booster pump bushes from the brake booster with accumulator pump assembly.


f.
U116681

Using a 4 mm hexagon wrench, remove the 2 pins.


Hide 47967A 7.REMOVE NO. 1 BRAKE BOOSTER PUMP BRACKET

a.
U116678

Using a 5 mm hexagon wrench, remove the 2 bolts and No. 1 brake booster pump bracket from the brake master cylinder solenoid.


b.

Remove the brake booster pump bush from the No. 1 brake booster pump bracket.


Hide 8.REMOVE NO. 3 BRAKE ACTUATOR BRACKET

a.
F051423

Remove the bolt and No. 3 brake actuator bracket from the brake master cylinder.


Hide 47955A 9.REMOVE BRAKE BOOSTER ACCUMULATOR PIPE

a.
C217129

Secure the brake booster with accumulator pump assembly in a vise.


b.

Remove the brake booster accumulator.


c.

Remove the O-ring from the brake booster accumulator.

NOTICE:

Make sure no foreign matter enters the pump.



d.

Remove the brake booster accumulator pipe and compression spring.


Hide 47217 10.REMOVE MASTER CYLINDER SOLENOID

a.
U116680

Remove the 6 bolts and master cylinder solenoid.


b.
F051196

Remove the gasket.


Hide 47264 11.REMOVE MASTER CYLINDER PUSH ROD CLEVIS

a.
C177091

Loosen the lock nut on the rod operating adapter and remove the push rod clevis and lock nut.


b.
U116679

Loosen the lock nut on the brake master cylinder side and remove the rod operating adapter and lock nut.


Hide 47265 12.REMOVE MASTER CYLINDER BOOT

Hide 13.REMOVE BRAKE BOOSTER PISTON SUB-ASSEMBLY

a.
F051417E18
1.792,0.906 1.646,0.781 1.646,0.781 1.49,0.781 true 1.979,1.813 2.25,1.958 2.25,1.958 2.375,1.958 false 2.406,1.854 2.563,2.031 0.156,0.177 10 false *2 1.281,0.688 1.458,0.865 0.177,0.177 10 false *1

Pressing the piston in with a screwdriver, use a pin or equivalent to push the C-ring from the hole in the master cylinder body and then remove it with another screwdriver.

Text in Illustration
*1 C-Ring
*2 Pin

HINT:

Pressing the piston in with a screwdriver, use a pin or equivalent to push the C-ring from the hole in the master cylinder body and then remove it with another screwdriver.



b.

Remove the plug from the piston.


c.

Remove the piston by pulling it straight out, not at an angle.

NOTICE:

If the piston pulled out at an angle, there is a possibility that the cylinder bore could be damaged.