Home › Brake › BRAKE (REAR) › REAR BRAKE FLEXIBLE HOSE
RM27T0E _54 Brake _053715 BRAKE (REAR) _0260938 REAR BRAKE FLEXIBLE HOSE A

BRAKE (REAR)  REAR BRAKE FLEXIBLE HOSE  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 47355A 1.INSTALL NO. 5 FLEXIBLE HOSE BRACKET

a.

for 3 Door:

i.

Install the bracket with the bolt.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)

NOTICE:

Make sure the bracket rotation stopper touches the installation position.




b.

for 5 Door:

i.

Install the bracket with the bolt.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)

NOTICE:

Make sure the bracket rotation stopper touches the installation position.




Hide 47356 2.INSTALL NO. 6 FLEXIBLE HOSE BRACKET

a.

Install the bracket with the bolt.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 47319F 3.INSTALL REAR FLEXIBLE HOSE

a.

Connect the rear flexible hose to the connecting point with each brake tube, and then install 2 new clips.


b.

Using a union nut wrench, connect each brake tube to the rear flexible hose while holding the rear flexible hose with a wrench.

Torque:
15 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:
·

Do not bend or damage the brake tube.

·

Do not allow any foreign matter such as dirt and dust to enter the brake tube from the connecting point.

·

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).




c.

Connect the rear flexible hose to the connecting point with each brake tube, and then install 2 new clips.


d.

Using a union nut wrench, connect each brake tube to the rear flexible hose while holding the rear flexible hose with a wrench.

Torque:
15 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:
·

Do not bend or damage the brake tube.

·

Do not allow any foreign matter such as dirt and dust to enter the brake tube from the connecting point.

·

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).




Hide 47319F 4.INSTALL REAR FLEXIBLE HOSE LH

a.

Connect the rear flexible hose to the connecting point with the brake tube, and then install a new clip.


b.

Using a union nut wrench, connect the brake tube to the rear flexible hose while holding the rear flexible hose with a wrench.

Torque:
15 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:
·

Do not bend or damage the brake tube.

·

Do not allow any foreign matter such as dirt and dust to enter the brake tube from the connecting point.

·

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).




c.

Install the rear flexible hose and a new gasket to the rear disc brake cylinder with the new union bolt.

Torque:
31 N*m (316 kgf*cm, 23 ft.*lbf)

HINT:

Install the flexible hose lock securely to the lock hole in the cylinder.



Hide 5.BLEED BRAKE LINE (for Hydraulic Brake Booster)

Hide 42603 7.INSTALL REAR WHEEL

Torque:
for Aluminum Wheel : 103 N*m (1050 kgf*cm, 76 ft.*lbf)
for Steel Wheel : 112 N*m (1137 kgf*cm, 82 ft.*lbf)