Home › Steering › POWER ASSIST SYSTEMS › VANE PUMP (for 1GD-FTV)
RM27T0E _55 Steering _053717 POWER ASSIST SYSTEMS _0260953 VANE PUMP(for 1GD-FTV) A

POWER ASSIST SYSTEMS  VANE PUMP(for 1GD-FTV)  REASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:

When installing parts, coat the parts indicated by arrows with power steering fluid (See page Steering>POWER ASSIST SYSTEMS>VANE PUMP (for 1GD-FTV)>COMPONENTS).


PROCEDURE

Hide 1.INSTALL VANE PUMP HOUSING OIL SEAL

a.
C327759

Coat the inside surface of the busing in the vane pump front housing with power steering fluid.

Text in Illustration
V100135

Power Steering Fluid


b.
C327757E01
2.731,0.625 2.438,0.562 2.438,0.562 2.623,0.819 false 2.043,0.453 2.460,0.662 0.417,0.209 10 SST

Using SST and a press, press in the vane pump housing oil seal.

SST
09950-60010  (09951-00280)
09950-70010  (09951-07100)

NOTICE:
·

Make sure to install the vane pump housing oil seal so that it is facing in the correct direction.

·

Be careful not to damage the vane pump housing oil seal.




c.
C327758

Coat the lip of a new vane pump housing oil seal with MP grease.

Text in Illustration
V100135

MP Grease


Hide 2.INSTALL VANE PUMP SHAFT WITH PULLEY

a.
C327760E02
1.854,1.031 2.083,1.698 2.083,1.698 2.281,1.698 true 2.323,1.625 2.646,1.854 0.323,0.229 10 false *a

Install the vane pump shaft with pulley to the vane pump front housing.

Text in Illustration
*a Protective Tape

NOTICE:
·

Wrap protective tape around the spline of the vane pump shaft with pulley in order to prevent damage to the vane pump housing oil seal.

·

Be careful not to damage the vane pump housing oil seal.




Hide 3.INSTALL VANE PUMP FRONT SIDE PLATE

a.
C327761

Coat a new O-ring with power steering fluid and install to the vane pump front housing.

Text in Illustration
V100135

Power Steering Fluid


b.
C324280

Coat a new O-ring with power steering fluid and install it to the vane pump front side plate.

Text in Illustration
V100135

Power Steering Fluid
V113147

Install in this Direction


c.
C327762

Install the vane pump front side plate to the vane pump front housing while aligning the semicircle-shaped cuts of both parts.

Text in Illustration
V113147

Install in this Direction

NOTICE:

Be sure to install the vane pump front side plate in the correct position and so that it is facing the correct direction.



Hide 4.INSTALL VANE PUMP CAM RING

a.
C324278E01
0.923,0.475 0.708,0.397 false 0.456,0.271 0.815,0.462 0.360,0.191 10 *a

With the inscribed mark facing upward, install the vane pump cam ring to the vane pump front housing while aligning the semicircle-shaped cutouts of both parts.

Text in Illustration
*a Inscribed Mark
V113147

Install in this Direction

NOTICE:

Be sure to install the vane pump cam ring in the correct position and with the correction,



Hide 5.INSTALL VANE PUMP ROTOR

a.
C327764

Install the vane pump rotor to the vane pump front housing.

Text in Illustration
V113147

Install in this Direction

HINT:

The top bottom of the vane pump rotor are symmetrical.



b.

Coat the 10 vane pump plates with power steering fluid.


c.
C324329E02
0.563,1.042 0.927,1.313 0.365,0.271 10 false *a 2.208,0.198 2.573,0.469 0.365,0.271 10 false *b

Install the 10 vane pump plates.

Text in Illustration
*a Outward
*b Inward

NOTICE:

Make sure that the round ends of the vane pump plates are facing outward.



Hide 6.INSTALL VANE PUMP SHAFT SNAP RING

a.
C322721

Using a screwdriver and snap ring expander, install a new snap ring to the vane pump shaft with pulley.


Hide 7.INSTALL VANE PUMP REAR HOUSING

a.
C330540

Coat a new O-ring with power steering fluid and install it to the vane pump rear housing.

Text in Illustration
V100135

Power Steering Fluid
V113147

Install in this Direction


b.
C327765

Coat the vane pump rear housing of the vane pump shaft with pulley and the surrounding surface with power steering fluid.

Text in Illustration
V100135

Power Steering Fluid


c.

Align the straight pin of the vane pump rear housing with the hole created by the semicircle-shaped cutouts of the cam ring, front side plate and vane pump front housing.

NOTICE:

Make sure that the O-ring is not out of position before installing the vane pump rear housing.



d.

Install the vane pump rear housing with the 4 bolts.

Torque:
22 N*m (224 kgf*cm, 16 ft.*lbf)


Hide 9.INSPECT TOTAL PRELOAD

a.

Check that the pump rotates smoothly without abnormal noise.


b.
C324332

Temporarily install a service bolt.

Recommended Service Bolt:
Item Specified Condition
Thread diameter 10 mm (0.394 in.)
Thread pitch 1.25 mm (0.0492 in.)
Bolt length 50 mm (1.97 in.)



c.

Using a torque wrench, check the rotating torque.

Standard Rotating torque:

0.3 N*m (3 kgf*cm, 2 in.*lbf) or less


If the rotating torque is not as specified, check the installation condition of each part.


Hide 10.INSTALL SUCTION PORT UNION

a.

Coat a new O-ring with power steering fluid.


b.

Install the O-ring to the suction port union.


c.

Install the suction port union to the vane pump front housing with the bolt.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)