Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY (for Manual Tilt and Manual Telescopic Steering Column)
RM27T0E _55 Steering _053718 STEERING COLUMN _0260957 STEERING COLUMN ASSEMBLY(for Manual Tilt and Manual Telescopic Steering Column) A

STEERING COLUMN  STEERING COLUMN ASSEMBLY(for Manual Tilt and Manual Telescopic Steering Column)  DISASSEMBLY  


PROCEDURE

Hide 45020A 1.REMOVE STEERING LOCK ACTUATOR ASSEMBLY

a.

Using a center punch, mark the center of the tapered-head bolt.


b.

Using a 3 to 4 mm (0.118 to 0.157 in.) drill, drill a hole in the bolt.


c.
C215853E01
0.223,0.178 0.580,0.392 0.358,0.214 12 *A 0.223,2.619 0.580,2.833 0.358,0.214 12 *B

Using a screw extractor, remove the bolt and steering lock actuator assembly from the steering column assembly.

Text in Illustration
*A w/o Entry and Start System
*B w/ Entry and Start System


Hide 69057A 2.REMOVE IGNITION SWITCH LOCK CYLINDER ASSEMBLY (w/o Entry and Start System)

a.

Turn the ignition switch to ON (ACC).


b.
C128808E04
2.104,0.667 2.135,0.354 2.135,0.354 2.188,0.354 true 2.146,0.76 2.229,0.979 2.229,0.979 2.281,0.979 true 0.958,0.708 1.177,0.875 0.219,0.167 10 false *a 1.74,2.594 2.031,2.76 0.292,0.167 10 false *b 2.219,0.26 2.417,0.417 0.198,0.156 10 true *1 2.313,0.906 2.531,1.094 0.219,0.188 10 true *2

Insert the tip of a screwdriver into the hole in the steering column upper bracket, as shown in the illustration, and pull the ignition switch lock cylinder out until its claw comes into contact with the stopper of the steering column upper bracket.

Text in Illustration
*1 Claw
*2 Stopper
*a Push
*b Pull

NOTICE:

Pull the ignition switch lock cylinder assembly out until its claw comes into contact with the stopper of the steering column bracket assembly upper. Otherwise, the following procedure cannot be conducted properly.



c.
C358683E01
0.51,1.031 0.615,0.354 0.615,0.354 0.74,0.354 true 2.229,1.01 2.396,0.354 2.396,0.354 2.542,0.354 true 0.365,1.729 0.25,1.729 0.25,1.729 0.438,1.073 true 0.979,1.677 0.813,1.677 0.813,1.677 0.625,1.104 true 0.781,0.25 1.094,0.448 0.313,0.198 10 false *1 2.594,0.271 2.906,0.469 0.313,0.198 10 false *c 0.427,1.667 0.74,1.865 0.313,0.198 10 false *2 1.01,1.583 1.323,1.781 0.313,0.198 10 true *d 1.708,2.49 2.021,2.688 0.313,0.198 10 false *a 1.865,4.229 2.177,4.427 0.313,0.198 10 false *b

Insert the tip of a screwdriver into the hole in the steering column bracket and tilt it downward, as shown in the illustration, to disengage the claw of the ignition switch lock cylinder. Then pull out the ignition switch lock cylinder.

Text in Illustration
*1 Stopper
*2 Claw
*a Tilt
*b Pull out
*c Claw is disengaged
*d Driver insertion hole


Hide 84052 3.REMOVE UNLOCK WARNING SWITCH ASSEMBLY (w/o Entry and Start System)

a.
C128810

Push up the unlock warning switch center portion to disengage the 2 claws.

HINT:

Slide the unlock warning switch in the direction shown by the arrow in the illustration to remove it.



Hide 85432 4.REMOVE KEY INTERLOCK SOLENOID (w/o Entry and Start System for Automatic Transmission)

a.

Disconnect the connector.


b.
C128811

Remove the 2 screws and remove the key interlock solenoid from the steering column upper bracket.


Hide 84450 5.REMOVE IGNITION SWITCH ASSEMBLY (w/o Entry and Start System)

a.
C128812

Remove the 2 screws and remove the ignition switch from the steering column upper bracket.


Hide 82291D 6.REMOVE KEY INTERLOCK SOLENOID WIRE (w/o Entry and Start System)

a.

Remove the key interlock solenoid wire from the ignition switch.